JCB · Engine ECU (Dieselmax / Ecomax) - temperature sensors
JCB Fault Code P0118
Coolant temperature sensor signal high
What does JCB code P0118 mean?
The voltage from the coolant sensor is too high, which reads as an extremely cold engine, usually an open circuit. Urgency: check soon - the machine may derate or limit a function. Check first: read the live coolant temperature with the engine warm and confirm it is stuck at a very low value.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read the live coolant temperature with the engine warm and confirm it is stuck at a very low value
Then 5 more checksWhere this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
Checks
0 of 6 done
Causes
- Open circuit in the coolant sensor wiring near the thermostat housing
- Coolant sensor unplugged, or its pins corroded by coolant seepage
- Signal wire shorted to the 5 V reference or to supply
- Coolant temperature sensor failed open
1 more causeFewer causes
- Wire broken at the plug from engine vibration
How it failed
You'll notice: The ECU thinks the coolant is stone cold on a warm engine, so it may idle fast, smoke white, run rich and start hard when hot, and the cab temperature gauge reads low or not at all.
Open circuitRead from how the source describes the code
No current flows, or the signal floats - a wire, pin or coil is broken.
- Meter test
- Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
- Good result
- Near 0 Ω on each wire. The part reads its listed resistance, not OL.
When to stop
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Fuel, oil and coolant temperature sensors and engine overheating
- P0115Coolant temperature sensor 1 circuit faultOtherCheck soon
- P0116Coolant temperature sensor range/performanceErratic or implausibleCheck soon
- P0117Coolant temperature sensor signal lowShorted lowCheck soon
- P0118Coolant temperature sensor signal highOpen circuitCheck soon
- P0180Fuel temperature sensor A circuit faultErratic or implausibleCheck soon
- P0181Fuel temperature sensor faultErratic or implausibleCheck soon
- P0181-87Missing fuel temperature CAN messageLost messageCheck soon
- P0182Fuel temperature sensor A signal lowOtherCheck soon
- P0183Fuel temperature sensor A signal highShorted highCheck soon
Show the other 9 codesHide the other codes
- P0195Oil temperature sensor external voltage faultOtherCheck soon
- P0196Oil temperature sensor signal gradient faultLost messageCheck soon
- P0196-87Missing oil temperature CAN message from engine ECULost messageCheck soon
- P0197Oil temperature sensor signal lowOtherCheck soon
- P0198Oil temperature sensor signal highShorted highCheck soon
- P0217Coolant temperature above limit (overheating)Shorted highStop now
- C1021Engine coolant level lowOtherCheck soon
- B1543Critical high coolant temperatureLost messageStop now
- B1546Coolant temperature high (operator level)OtherCheck soon
Other JCB codes: Engine ECU (Dieselmax / Ecomax) - temperature sensors
Related on Equipments Finder
Source
Partao JCB fault code P0118 page
This source lists P0118 and its meaning. The guidance on this page is general, not taken from it.
The source covers: JS140, JS205, JS215 and 212.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
