EF Logo

JCB · Engine ECU (Dieselmax / Ecomax) - injectors

JCB Injector circuits: open, low, high and performance fault codes

Each injector is an electrically operated valve driven by the ECU through a high-side and low-side wire. These codes say the ECU sees an open injector circuit for a named cylinder or for the whole engine.

More about these parts

These codes report the electrical state of an injector circuit for a named cylinder: low voltage, high voltage or a performance problem. Low usually points toward ground, high toward supply or a resistance problem in the wiring.

FaultCheckP0201JCB · Injector circuits: open, low, high and performance
Code shows hereFAULTP0201

Where this code shows

Switch the key on and note any warning lamp or fault icon on the cluster.

What do these codes mean?

JCB codes P02EE to P0277 are all about the injector circuits: open, low, high and performance. The most common failure type is open circuit (7 of 25); none needs an immediate stop. Start with this check: measure the injector coil resistance across its two pins and compare it with the other cylinders.

How urgent are they?

None of the 25 codes here means stop now; all 25 can wait until the shift ends, but find the cause before the next one.

  • Check soon25

What should I check first?

Measure the injector coil resistance across its two pins and compare it with the other cylinders

Shared checks

25 of 25

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • JCB P02EECylinder 1 injector circuit performance issue

    The ECU found the cylinder 1 injector circuit working outside its expected range or performance, even though the wiring is not clearly shorted or open.· Lost message
    Check soon

    Causes

    • Cylinder 1 injector coil resistance drifted
    • Intermittent contact in the cylinder 1 plug

    Checks

    1. 1Measure cylinder 1 coil resistance when cold and again after the engine has warmed up
    2. 2Flex the injector harness while monitoring for a changing reading
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P02EFCylinder 2 injector circuit performance issue

    Same fault as P02EE on the cylinder 2 injector: the injector circuit is working outside its range or performance limits.· Other
    Check soon

    Causes

    • Cylinder 2 injector coil resistance drifted out of range
    • Intermittent contact at the cylinder 2 plug or pass-through

    Checks

    1. 1Measure cylinder 2 injector coil resistance cold and warm and compare with its neighbour
    2. 2Swap the cylinder 2 and cylinder 1 connectors and see whether the code follows
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P02F0Cylinder 3 injector circuit range/performance

    Same fault as P02EE on the cylinder 3 injector: the injector circuit is working outside its range or performance limits.· Other
    Check soon

    Causes

    • Cylinder 3 injector coil resistance drifted out of range
    • Intermittent contact at the cylinder 3 plug or pass-through

    Checks

    1. 1Measure cylinder 3 injector coil resistance cold and warm and compare with its neighbour
    2. 2Swap the cylinder 3 and cylinder 2 connectors and see whether the code follows
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P02F1Injector circuit range/performance issue

    The ECU raised the injector circuit range and performance fault without a cylinder number in the title.· Other
    Check soon

    Causes

    • One injector coil drifting out of range
    • Intermittent contact on one injector plug

    Checks

    1. 1Use the diagnostic tool's injector test to identify the failing cylinder before taking anything apart
    2. 2Measure each injector coil at the plug and compare the cylinders with each other
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P02F2Cylinder 5 injector circuit range/performance

    Same fault as P02EE on the cylinder 5 injector: the injector circuit is working outside its range or performance limits.· Other
    Check soon

    Causes

    • Cylinder 5 injector coil resistance drifted out of range
    • Intermittent contact at the cylinder 5 plug or pass-through

    Checks

    1. 1Measure cylinder 5 injector coil resistance cold and warm and compare with its neighbour
    2. 2Swap the cylinder 5 and cylinder 4 connectors and see whether the code follows
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P02F3Cylinder 6 injector circuit range/performance

    Same fault as P02EE on the cylinder 6 injector: the injector circuit is working outside its range or performance limits.· Other
    Check soon

    Causes

    • Cylinder 6 injector coil resistance drifted out of range
    • Intermittent contact at the cylinder 6 plug or pass-through

    Checks

    1. 1Measure cylinder 6 injector coil resistance cold and warm and compare with its neighbour
    2. 2Swap the cylinder 6 and cylinder 5 connectors and see whether the code follows
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P0200Injector circuit open

    Injector circuit open.· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the injector circuit open
    • Injector circuit open coil, element or sensor internally open

    Checks

    1. 1Unplug the injector circuit open and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the injector circuit open plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P0201Injector circuit open, cylinder 1

    The ECU sees an open circuit on the cylinder 1 injector when it commands it to fire.· Open circuit
    Check soon

    Causes

    • Open circuit in the cylinder 1 injector solenoid coil
    • Broken wire or backed-out pin in the cylinder 1 injector connector under the valve cover
    • Cylinder 1 loom leg chafed or cracked where it leaves the valve cover
    • Corroded injector plug leaving the circuit open only when hot or vibrating
    • ECU injector driver failure for this channel, only once wiring and injector pass

    Checks

    1. 1Unplug the cylinder 1 injector and measure its coil resistance across the two pins for an open reading
    2. 2Compare that reading with the other three injectors on the same engine
    3. 3Check continuity of both cylinder 1 injector wires back to the ECU connector
    4. 4Inspect the valve cover seal area for oil that has wicked up the harness
    5. 5Wiggle the cylinder 1 loom leg with live data open to catch an intermittent open
    6. 6Run the injector cut-out test and confirm cylinder 1 makes no contribution
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P0202Injector circuit open, cylinder 2

    The ECU sees an open circuit on the cylinder 2 injector when it commands it to fire.· Open circuit
    Check soon

    Causes

    • Cylinder 2 injector coil failed open after heat and age
    • Terminal pushed back out of the cylinder 2 injector plug
    • Cylinder 2 injector wires rubbed through against the rocker cover or a bracket

    Checks

    1. 1Swap the cylinder 2 injector plug with a neighbouring one: if the fault code follows, the wiring or ECU is at fault, not the injector
    2. 2Measure the cylinder 2 coil resistance and compare it with a good injector
    3. 3Check that each wire to cylinder 2 is continuous to the ECU pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P0203Injector circuit open, cylinder 3

    The ECU sees an open circuit on the cylinder 3 injector when it commands it to fire.· Open circuit
    Check soon

    Causes

    • Open coil in the cylinder 3 injector
    • Cylinder 3 plug damaged or unseated after the valve cover was removed
    • Insulation worn through where the cylinder 3 wires pass over a sharp bracket edge

    Checks

    1. 1Read the live fault and see if it comes back immediately after clearing, which points to a hard open circuit
    2. 2Measure resistance across the cylinder 3 injector pins and look for an open or a very high value
    3. 3Pull back the harness covering and look for a broken wire close to the plug
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P0204Injector circuit open, cylinder 4

    The ECU sees an open circuit on the cylinder 4 injector when it commands it to fire.· Open circuit
    Check soon

    Causes

    • Cylinder 4 injector solenoid open internally
    • Terminal fretted or corroded in the cylinder 4 injector connector
    • Cylinder 4 wires damaged where the loom is clipped near the end of the engine

    Checks

    1. 1Measure the cylinder 4 injector coil resistance with the connector unplugged
    2. 2Compare the result with cylinders 1 to 3 on the same engine
    3. 3Verify the feed-through plug at the valve cover and its wires are continuous
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P0205Injector circuit open, cylinder 5

    Injector circuit open, cylinder 5.· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the injector circuit open
    • Injector circuit open coil, element or sensor internally open

    Checks

    1. 1Unplug the injector circuit open and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the injector circuit open plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P0206Injector circuit open, cylinder 6

    Injector circuit open, cylinder 6.· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the injector circuit open
    • Injector circuit open coil, element or sensor internally open

    Checks

    1. 1Unplug the injector circuit open and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the injector circuit open plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P0261Injector circuit low, cylinder 1

    The engine ECU measured low voltage on the injector drive for cylinder 1, which means the injector circuit is pulled toward ground or the supply side is lost.· Shorted low
    Check soon

    Causes

    • Injector lead for cylinder 1 chafed and touching engine ground
    • Cylinder 1 injector coil shorted internally
    • Loose or corroded pin at the cylinder 1 connector on the injector or at the rocker cover pass-through

    Checks

    1. 1Remove the cylinder 1 injector connector and measure coil resistance, then compare it with another cylinder's injector
    2. 2Measure each injector wire to ground with the key off to prove a short to ground
    3. 3Check the injector wiring at the valve cover pass-through for oil soaking and rubbed insulation
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P0262Injector circuit high, cylinder 1

    The engine ECU measured high voltage on the cylinder 1 injector drive, which means the injector circuit is open or shorted toward a supply wire.· Shorted high
    Check soon

    Causes

    • Open injector coil or open lead on cylinder 1
    • Cylinder 1 injector wire shorted to a live wire in the harness
    • Terminal backed out of the cylinder 1 plug

    Checks

    1. 1Measure the cylinder 1 injector coil resistance; an open circuit reads as no continuity
    2. 2Check the cylinder 1 wires for continuity from the injector plug to the engine ECU connector
    3. 3Inspect the plug for a pushed-back terminal or green corrosion
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P0264Injector circuit low, cylinder 2

    Same fault as P0261 on the cylinder 2 injector: low voltage on that cylinder's drive line.· Shorted low
    Check soon

    Causes

    • Cylinder 2 injector lead chafed against ground or a bracket
    • Cylinder 2 injector coil shorted internally

    Checks

    1. 1Swap the cylinder 2 injector connector with cylinder 1's; if the code follows the plug, the injector or its lead is at fault, if it stays the ECU driver or harness is suspect
    2. 2Measure cylinder 2 coil resistance at the plug and compare it with the other injectors
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P0265Injector circuit high, cylinder 2

    Same fault as P0262 on the cylinder 2 injector: high voltage on that cylinder's drive line, an open or supply short.· Shorted high
    Check soon

    Causes

    • Cylinder 2 injector coil open or its lead broken
    • Cylinder 2 plug terminal pushed back or corroded

    Checks

    1. 1Check continuity of both cylinder 2 injector wires from the plug to the ECU connector
    2. 2Swap the cylinder 2 and cylinder 1 plugs; a code that moves to the other cylinder points to the injector side
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P0267Injector circuit low, cylinder 3

    Same fault as P0261 on the cylinder 3 injector: low voltage on that cylinder's drive line.· Shorted low
    Check soon

    Causes

    • Cylinder 3 injector lead chafed against ground or a bracket
    • Cylinder 3 injector coil shorted internally

    Checks

    1. 1Swap the cylinder 3 injector connector with cylinder 2's; if the code follows the plug, the injector or its lead is at fault, if it stays the ECU driver or harness is suspect
    2. 2Measure cylinder 3 coil resistance at the plug and compare it with the other injectors
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P0268Injector circuit high, cylinder 3

    Same fault as P0262 on the cylinder 3 injector: high voltage on that cylinder's drive line, an open or supply short.· Shorted high
    Check soon

    Causes

    • Cylinder 3 injector coil open or its lead broken
    • Cylinder 3 plug terminal pushed back or corroded

    Checks

    1. 1Check continuity of both cylinder 3 injector wires from the plug to the ECU connector
    2. 2Swap the cylinder 3 and cylinder 2 plugs; a code that moves to the other cylinder points to the injector side
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P0270Injector circuit low, cylinder 4

    Same fault as P0261 on the cylinder 4 injector: low voltage on that cylinder's drive line.· Shorted low
    Check soon

    Causes

    • Cylinder 4 injector lead chafed against ground or a bracket
    • Cylinder 4 injector coil shorted internally

    Checks

    1. 1Swap the cylinder 4 injector connector with cylinder 3's; if the code follows the plug, the injector or its lead is at fault, if it stays the ECU driver or harness is suspect
    2. 2Measure cylinder 4 coil resistance at the plug and compare it with the other injectors
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P0271Injector circuit high, cylinder 4

    Same fault as P0262 on the cylinder 4 injector: high voltage on that cylinder's drive line, an open or supply short.· Shorted high
    Check soon

    Causes

    • Cylinder 4 injector coil open or its lead broken
    • Cylinder 4 plug terminal pushed back or corroded

    Checks

    1. 1Check continuity of both cylinder 4 injector wires from the plug to the ECU connector
    2. 2Swap the cylinder 4 and cylinder 3 plugs; a code that moves to the other cylinder points to the injector side
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P0273Injector circuit low, cylinder 5

    Same fault as P0261 on the cylinder 5 injector: low voltage on that cylinder's drive line.· Shorted low
    Check soon

    Causes

    • Cylinder 5 injector lead chafed against ground or a bracket
    • Cylinder 5 injector coil shorted internally

    Checks

    1. 1Swap the cylinder 5 injector connector with cylinder 4's; if the code follows the plug, the injector or its lead is at fault, if it stays the ECU driver or harness is suspect
    2. 2Measure cylinder 5 coil resistance at the plug and compare it with the other injectors
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P0274Injector circuit high, cylinder 5

    Same fault as P0262 on the cylinder 5 injector: high voltage on that cylinder's drive line, an open or supply short.· Shorted high
    Check soon

    Causes

    • Cylinder 5 injector coil open or its lead broken
    • Cylinder 5 plug terminal pushed back or corroded

    Checks

    1. 1Check continuity of both cylinder 5 injector wires from the plug to the ECU connector
    2. 2Swap the cylinder 5 and cylinder 4 plugs; a code that moves to the other cylinder points to the injector side
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P0276Injector circuit fault (injector 3 resistance out of range)

    The ECU measured the resistance of the cylinder 3 injector circuit outside the expected window.· Other
    Check soon

    Causes

    • Cylinder 3 injector coil resistance drifted out of range
    • High resistance in the cylinder 3 plug from corrosion or a loose pin

    Checks

    1. 1Measure cylinder 3 injector coil resistance at the injector and at the harness plug; a difference between the two readings shows wiring resistance
    2. 2Clean and reseat the cylinder 3 connector and read the code again
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P0277Injector circuit high signal

    The ECU flagged a high signal on an injector drive circuit without naming the cylinder in the title.· Other
    Check soon

    Causes

    • An injector coil open on one of the cylinders
    • Open or loose lead between the injector and the ECU

    Checks

    1. 1Run the injector or cylinder cut-out test with the diagnostic tool to find which cylinder has no current
    2. 2Measure each injector coil in turn and look for the open one
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Measure the injector coil resistance across its two pins and compare it with the other cylinders
  2. 2Measure the injector coil resistance and compare it with the other cylinders
  3. 3Check each wire from the injector plug to the ECU for continuity
  4. 4Check each injector wire for a short to ground and to battery with the plug removed
  5. 5Inspect the injector connector or feed-through under the valve cover for water and oil
  6. 6Look for chafing where the harness crosses the valve cover and brackets
  7. 7Wiggle the harness with live data on screen to catch an intermittent open

Causes

  • Injector coil open
  • Injector coil shorted or resistance out of range
  • Broken wire or pushed-back pin in the injector connector
  • Harness chafed against the engine and touching ground or supply

Most common here: open circuit (7 of 25)

Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

When to stop

You'll notice: The engine runs rough or on fewer cylinders, with misfire, smoke and a loss of power, and a check lamp is on.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.