JCB · Engine ECU (Dieselmax / Ecomax) - injectors
JCB Injector cylinder balancing and MDP learning fault codes
The ECU measures how much each cylinder contributes to engine speed and trims the fuel to even them out. When a cylinder needs a trim at its limit, the ECU logs a balancing fault for that cylinder.
More about these partsLess
MDP is the minimum drive pulse, the shortest electrical pulse that makes an injector deliver fuel. The ECU learns it for each injector, and runs an update after an injector is replaced. These codes record a trim past its limit or an update that could not finish.
Where this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
What do these codes mean?
JCB codes P02AA to P1109 are all about the injector cylinder balancing and MDP learning. The most common failure type is real condition (4 of 28); none needs an immediate stop. Start with this check: use the injector balance or cylinder cut-out test on the diagnostic tool to confirm which cylinder is weak.
How urgent are they?
None of the 28 codes here means stop now; all 28 can wait until the shift ends, but find the cause before the next one.
- Check soon28
What should I check first?
Use the injector balance or cylinder cut-out test on the diagnostic tool to confirm which cylinder is weak
Shared checks28 of 28
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
JCB P02AAInjector 1 MDP trim exceeds calibrated maximum
The learned minimum drive pulse (MDP) for injector 1 has moved past the calibrated maximum. The injector now needs more electrical pulse than the ECU allows before it starts to deliver fuel.· Real conditionReal conditionCheck soonCauses
- Injector 1 worn or sticking so it needs a longer pulse
- Injector 1 trim data wrong after replacement
- Low supply voltage during the learning routine
Checks
- 1Check battery and supply voltage during the next MDP learn
- 2Run the MDP learn routine again and note whether injector 1 passes
- 3Check the injector 1 trim code is correct for the fitted injector
- 4Check the injector hold-down clamp for looseness and the copper sealing washer for a blow-by track
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JCB P02ABInjector 1 MDP trim exceeds threshold
Injector 1 MDP trim exceeds its threshold: the correction applied to its minimum drive pulse is bigger than the ECU accepts. This is a warning that injector 1 is drifting out of specification.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Injector 1 beginning to wear or stick
- Injector 1 contaminated by poor fuel
- Wrong trim code stored for injector 1
Checks
- 1Compare the injector 1 MDP trim value with that of the other injectors on live data
- 2Fix any other fuel-system fault first, then repeat the MDP learn
- 3Look at the exhaust at idle for a puff of white or black smoke that pulses with one cylinder
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P02AEInjector 3 MDP trim exceeds threshold
Injector 3 MDP trim exceeds its threshold: the correction applied to its minimum drive pulse is bigger than the ECU accepts.· Real conditionReal conditionCheck soonCauses
- Injector 3 worn or sticking
- Injector 3 trim code wrong or lost
Checks
- 1Read the injector 3 MDP trim on live data and compare it with the others
- 2Repeat the learn routine once any other fuel fault is cleared
- 3Pinch the rail return hose briefly and watch idle quality, a standard way to spot an injector leaking back excess fuel
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JCB P02AFInjector 3 absolute MDP value below threshold
The absolute MDP value for injector 3 has fallen below its threshold: the injector opens on a pulse shorter than the ECU expects. It may be leaking or over-sensitive.· OtherOtherCheck soonCauses
- Injector 3 leaking or opening early
- Incorrect or missing injector trim code
Checks
- 1Check injector 3 for external leaks and for fuel dilution of the oil
- 2Confirm the injector 3 trim code against the label on the injector
- 3Compare the exhaust manifold branch temperature for this cylinder with its neighbours using an infrared thermometer
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P02A2Cylinder 3 fuel balancing at maximum limit
Cylinder 3 is at its maximum fuel balancing limit: the ECU adds the most fuel it may to cylinder 3 and that cylinder still contributes less than the others.· OtherOtherCheck soonCauses
- Cylinder 3 injector worn or restricted
- Cylinder 3 mechanical fault such as low compression
Checks
- 1Compare cylinder 3 compression or leak-down with the other cylinders
- 2Run the injector balance test and swap the cylinder 3 injector to confirm which side the fault is on
- 3Run the engine with the air filter restriction indicator in view to rule out an air supply problem affecting all cylinders
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P02A3Cylinder 3 fuel balancing at minimum limit
Cylinder 3 is at its minimum fuel balancing limit: the ECU has taken as much fuel off cylinder 3 as it may because that cylinder is stronger than the others.· OtherOtherCheck soonCauses
- Cylinder 3 injector leaking or stuck partly open
- Incorrect trim code for the cylinder 3 injector
Checks
- 1Check for fuel in the oil and for a smoky or rough cylinder 3 when cut out
- 2Check the injector trim code stored for cylinder 3
- 3Check the crankshaft speed sensor signal pattern, because a noisy tooth signal makes balance values wander
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P02A6Cylinder 4 fuel balancing at maximum limit
Cylinder 4 is at its maximum fuel balancing limit: the ECU cannot add more fuel to cylinder 4 and it still lags behind the other cylinders.· OtherOtherCheck soonCauses
- Cylinder 4 injector delivering too little
- Cylinder 4 compression loss
Checks
- 1Compare cylinder 4 contribution and compression with the other cylinders
- 2Swap the cylinder 4 injector with another cylinder and see whether the limit follows
- 3If the injector is removed, look at the nozzle tip for coking or a wet spray pattern
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P02A7Cylinder 4 fuel balancing at minimum limit
Cylinder 4 is at its minimum fuel balancing limit: the ECU has cut cylinder 4 fuel as far as allowed because that cylinder is stronger than the rest.· OtherOtherCheck soonCauses
- Cylinder 4 injector leaking or dribbling
- Injector trim code not matching the fitted injector
Checks
- 1Check cylinder 4 for external fuel leaks and for fuel in the sump oil
- 2Re-enter or verify the cylinder 4 injector trim code
- 3Draw a sample from the water separator drain and look for water droplets or sediment in the fuel
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P02A8Cylinder 4 fuel injector restricted
The ECU believes the cylinder 4 injector is restricted: the cylinder cannot get the fuel it is commanded, so the injector is blocked or delivering less than it should.· Real conditionReal conditionCheck soonCauses
- Blocked nozzle or filter screen in the cylinder 4 injector
- Contaminated or poor quality fuel
- Internal wear in the cylinder 4 injector
Checks
- 1Inspect the fuel filters and drain the water separator, then look at the fuel quality
- 2Run the injector test on cylinder 4 and compare its delivery with the others
- 3Listen along the cylinder head with a mechanic's stethoscope for a different injector tick on this cylinder compared with its neighbours
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JCB P02A9Cylinder 5 fuel production at minimum limit
Cylinder 5 is producing fuel at its minimum limit, so the ECU has reduced its fuel as far as allowed because cylinder 5 is stronger than the others.· OtherOtherCheck soonCauses
- Cylinder 5 injector leaking or over-delivering
- Wrong trim code for the cylinder 5 injector
Checks
- 1Check cylinder 5 for external leakage and fuel in the engine oil
- 2Compare cylinder 5 contribution with the others on live data
- 3Remove the injector return line and look for a faster dribble from this injector than from the others at idle
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P029AFuel production imbalance, cylinder 1
The ECU sees cylinder 1 producing a different amount of power than the rest, an imbalance in fuel production. It is a comparison fault between cylinders, not a single measured value.· OtherOtherCheck soonCauses
- Injector 1 flow different from the other injectors
- Contaminated fuel affecting one nozzle more than the others
Checks
- 1Run the injector balance test and note which way cylinder 1 deviates
- 2Inspect the fuel filters and fuel for water or debris that may block a nozzle
- 3Look for a diesel smell or thinning of the dipstick oil that would show fuel leaking past a nozzle
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P029BCylinder 1 fuel balancing at minimum limit
Cylinder 1 is at its minimum fuel trim limit, meaning the ECU has cut the fuel to that cylinder as far as it is allowed because it is producing more power than the others. The injector is probably over-delivering or leaking.· OtherOtherCheck soonCauses
- Cylinder 1 injector leaking or dribbling at the nozzle
- Injector trim data wrong after a replacement
- Excess fuel from a stuck-open injector
Checks
- 1Check that the cylinder 1 injector code was programmed correctly if it has been replaced
- 2Look for fuel in the engine oil, which would show an injector leaking into the cylinder
- 3Run the cylinder balance test and compare cylinder 1 with the rest
- 4Inspect the fuel rail stub fitting that feeds this injector for a seeping union
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P029ECylinder 2 fuel balancing at maximum limit
Cylinder 2 is at its maximum fuel trim limit: the ECU is adding as much fuel as it may and cylinder 2 is still the weaker cylinder. The injector, compression or a restriction is limiting it.· Real conditionReal conditionCheck soonCauses
- Cylinder 2 injector under-delivering from wear or a partly blocked nozzle
- Weak compression on cylinder 2
Checks
- 1Check cylinder 2 compression against the other cylinders
- 2Run the cylinder balance test and confirm cylinder 2 is the one lagging
- 3Check the valve clearance on this cylinder, since a tight valve reduces compression and shifts its contribution
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JCB P029FCylinder 2 fuel trim at minimum limit
Cylinder 2 is at its minimum fuel trim limit, so the ECU has reduced that cylinder's fuel as far as it may because it is delivering too much power.· OtherOtherCheck soonCauses
- Cylinder 2 injector leaking or dribbling
- Trim data for the injector not matching after replacement
Checks
- 1Check for fuel dilution in the engine oil and for external leaks around the cylinder 2 injector
- 2Confirm that the cylinder 2 injector correction code was entered correctly after the last replacement
- 3Check the injector's learned correction code against the label and re-enter it if a character is wrong
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P110AInjector 1 MDP update failure due to environmental conditions
The MDP update for injector 1 could not complete because conditions were wrong when the learning ran, for example the engine was too cold, too hot or running unevenly. The injector is not necessarily faulty.· OtherOtherCheck soonCauses
- Engine not at the required temperature for the routine
- Interrupted idle during the update, for example from load or a throttle input
Checks
- 1Warm the engine fully and repeat the update at steady idle with all loads off
- 2Check battery voltage and that no other fault is active
- 3If the injector is removed, look at the nozzle tip for coking or a wet spray pattern
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P110BInjector update failure (injector 6)
Same fault as P1105 for injector 6: the update routine did not finish and the old learned value is kept. Injector 6 may deliver slightly off until it is learned again.· OtherOtherCheck soonCauses
- Update for injector 6 interrupted
- An active fault blocking the update routine
Checks
- 1Repeat the update for injector 6 with the engine warm and idling steadily
- 2Check there are no active injector circuit faults before trying again
- 3Draw a sample from the water separator drain and look for water droplets or sediment in the fuel
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0263Cylinder 1 contribution / balance fault
The ECU judges that cylinder 1 is pulling more or less than its share of engine speed when it compares the crankshaft acceleration of each cylinder. That is a balance fault: this cylinder is not doing the same work as the others.· OtherOtherCheck soonCauses
- Cylinder 1 injector delivering the wrong quantity, from wear or a partly stuck nozzle
- Weak compression on cylinder 1
- Air leaking into the fuel supply and affecting one cylinder more than the others
Checks
- 1Run the cylinder cut-out or contribution test and compare cylinder 1 with the other cylinders
- 2Check cylinder 1 compression or a leak-down figure against the other cylinders
- 3Inspect the cylinder 1 injector for external leakage, and the clamp and sealing washer for damage
- 4Listen along the cylinder head with a mechanic's stethoscope for a different injector tick on this cylinder compared with its neighbours
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0266Cylinder 2 contribution / balance fault
Same fault as P0263 on cylinder 2: the ECU sees cylinder 2 contributing out of balance with the rest. The ECU raised the fault for this cylinder alone.· OtherOtherCheck soonCauses
- Cylinder 2 injector over- or under-delivering
- Low compression or a mechanical problem on cylinder 2
Checks
- 1Compare the cylinder 2 contribution value with the other cylinders on live data while idling
- 2Swap the cylinder 2 injector with another cylinder's and see whether the fault moves with the injector
- 3Remove the injector return line and look for a faster dribble from this injector than from the others at idle
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0269Cylinder 3 contribution / balance fault
Same fault as P0263 on cylinder 3: the ECU sees cylinder 3 contributing out of balance with the rest. The ECU raised the fault for this cylinder alone.· OtherOtherCheck soonCauses
- Cylinder 3 injector over- or under-delivering
- Low compression or a mechanical problem on cylinder 3
Checks
- 1Compare the cylinder 3 contribution value with the other cylinders on live data while idling
- 2Swap the cylinder 3 injector with another cylinder's and see whether the fault moves with the injector
- 3Check the injector hold-down clamp for looseness and the copper sealing washer for a blow-by track
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0272Cylinder 4 contribution / balance fault
Same fault as P0263 on cylinder 4: the ECU sees cylinder 4 contributing out of balance with the rest. The ECU raised the fault for this cylinder alone.· OtherOtherCheck soonCauses
- Cylinder 4 injector over- or under-delivering
- Low compression or a mechanical problem on cylinder 4
Checks
- 1Compare the cylinder 4 contribution value with the other cylinders on live data while idling
- 2Swap the cylinder 4 injector with another cylinder's and see whether the fault moves with the injector
- 3Look at the exhaust at idle for a puff of white or black smoke that pulses with one cylinder
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0275Cylinder balancing fault, injector stuck closed
The title names the injector as stuck closed in a cylinder balancing fault: the cylinder is delivering almost no fuel and the ECU cannot trim it high enough to match the others.· OtherOtherCheck soonCauses
- Injector needle stuck closed or nozzle blocked
- Injector control valve not opening, or a lost supply to that cylinder's injector
Checks
- 1Run the cylinder cut-out test; cutting the affected cylinder will make no difference to idle if it is not firing
- 2Check for fuel return flow from the injector with the engine at idle and compare it with the other cylinders
- 3Pinch the rail return hose briefly and watch idle quality, a standard way to spot an injector leaking back excess fuel
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0278Cylinder 6 contribution / balance fault
Same fault as P0263 on cylinder 6: the ECU sees cylinder 6 contributing out of balance with the rest. The ECU raised the fault for this cylinder alone.· OtherOtherCheck soonCauses
- Cylinder 6 injector over- or under-delivering
- Low compression or a mechanical problem on cylinder 6
Checks
- 1Compare the cylinder 6 contribution value with the other cylinders on live data while idling
- 2Swap the cylinder 6 injector with another cylinder's and see whether the fault moves with the injector
- 3Compare the exhaust manifold branch temperature for this cylinder with its neighbours using an infrared thermometer
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P1104Injector 3 MDP update failure due to environmental conditions
The MDP update for injector 3 could not complete because conditions were wrong when the routine ran. It is a failed learning attempt, not a measurement of the injector.· OtherOtherCheck soonCauses
- Engine temperature or idle not stable for the update
- Another active fault stopping the routine
Checks
- 1Repeat the update with the engine warm and idling steadily
- 2Read the other fault codes to make sure none stops the learning
- 3Look for a diesel smell or thinning of the dipstick oil that would show fuel leaking past a nozzle
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P1105Injector update failure
The injector update did not finish and the source does not name the injector. The ECU kept the old learned value, so fuel delivery for that injector may be slightly off.· OtherOtherCheck soonCauses
- Update routine interrupted before it finished
- Injector update not permitted by an active fault
Checks
- 1Read the freeze frame to see which injector failed, then repeat the update
- 2Check there are no active injector circuit faults
- 3Inspect the fuel rail stub fitting that feeds this injector for a seeping union
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P1106Injector 2 MDP update failure due to environmental conditions
The MDP update for injector 2 could not complete because conditions were wrong when the routine ran. It is a failed learning attempt, not a measurement of the injector.· OtherOtherCheck soonCauses
- Engine temperature or idle not stable for the update
- Another active fuel or sensor fault stopping the routine
Checks
- 1Clear the code, bring the engine to working temperature and repeat the update at idle with no loads
- 2Check for other fuel-system faults and clear them first
- 3Check the valve clearance on this cylinder, since a tight valve reduces compression and shifts its contribution
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P1107Injector update failure (injector 4)
Same fault as P1105 for injector 4: the update routine did not finish and the old learned value is kept. Injector 4 may deliver slightly off until it is learned again.· OtherOtherCheck soonCauses
- Update for injector 4 interrupted
- An active fault blocking the update routine
Checks
- 1Repeat the update for injector 4 with the engine warm and idling steadily
- 2Check there are no active injector circuit faults before trying again
- 3Check the injector's learned correction code against the label and re-enter it if a character is wrong
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P1108Injector 4 update failure
Same fault as P1105 for injector 4: the update routine did not finish and the old learned value is kept. Injector 4 may deliver slightly off until it is learned again.· OtherOtherCheck soonCauses
- Update for injector 4 interrupted
- An active fault blocking the update routine
Checks
- 1Repeat the update for injector 4 with the engine warm and idling steadily
- 2Check there are no active injector circuit faults before trying again
- 3Run the engine with the air filter restriction indicator in view to rule out an air supply problem affecting all cylinders
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P1109Injector update failure (injector 5)
Same fault as P1105 for injector 5: the update routine did not finish and the old learned value is kept. Injector 5 may deliver slightly off until it is learned again.· OtherOtherCheck soonCauses
- Update for injector 5 interrupted
- An active fault blocking the update routine
Checks
- 1Repeat the update for injector 5 with the engine warm and idling steadily
- 2Check there are no active injector circuit faults before trying again
- 3Check the crankshaft speed sensor signal pattern, because a noisy tooth signal makes balance values wander
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Use the injector balance or cylinder cut-out test on the diagnostic tool to confirm which cylinder is weak
- 2Check that every injector calibration code in the ECU matches the code on its injector
- 3Check compression on the flagged cylinder before replacing an injector
- 4Warm the engine fully and repeat the injector update on the diagnostic tool
- 5Check the fuel supply for air and the injector return flow for excess leakage
- 6Look for air or restriction in the fuel supply that upsets small injections
- 7Check the injector connector and calibration code for that cylinder
Causes
- Worn or sticking injector on that cylinder
- Injector worn so its minimum quantity has drifted
- Low compression on that cylinder
- Wrong or missing injector calibration code after an injector change
Most common here: real condition (4 of 28)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: The engine idles roughly, may knock or smoke and can lose power, and a check lamp is on.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Partao JCB fault code list, page 5 (code table)
- Partao JCB fault code list, page 7 (code table)
- Partao JCB fault code list, page 6 (code table)
- Partao JCB fault code list, page 9 (code table)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
