EF Logo

JCB · Aftertreatment ECU - SCR / DEF

JCB DEF line heaters fault codes

Heated lines carry DEF from the tank to the pump and on to the dosing valve, and a return line empties them at shutdown. The aftertreatment unit switches a heater on each line through a relay so the DEF cannot freeze in the cold.

FaultCheckP20BB-00JCB · DEF line heaters
Code shows hereFAULTP20BB-00

Where this code shows

Switch the key on and note any warning lamp or fault icon on the cluster.

What do these codes mean?

JCB codes P20BB-00 to P20BE-93 are all about the dEF line heaters. The most common failure type is open circuit (6 of 23); none needs an immediate stop. Start with this check: measure the resistance of the affected line heater at its plug and compare it with the other lines.

How urgent are they?

None of the 23 codes here means stop now; all 23 can wait until the shift ends, but find the cause before the next one.

  • Check soon23

What should I check first?

Measure the resistance of the affected line heater at its plug and compare it with the other lines

Shared checks

23 of 23

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • JCB P20BB-00DEF backflow line heater relay fault

    DEF backflow line heater relay fault.· Other
    Check soon

    Causes

    • DEF backflow line heater relay or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the DEF backflow line heater relay and look for a value that is stuck or implausible
    2. 2Check the DEF backflow line heater relay connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P20BD-00Pressure line heater relay open load

    Pressure line heater relay open load.· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the pressure line heater relay open load
    • Pressure line heater relay open load coil, element or sensor internally open

    Checks

    1. 1Unplug the pressure line heater relay open load and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the pressure line heater relay open load plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P20BE-00Pressure line heater fault

    Pressure line heater fault.· Other
    Check soon

    Causes

    • Pressure line heater or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the pressure line heater and look for a value that is stuck or implausible
    2. 2Check the pressure line heater connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P20BF-00DEF pressure line heater relay fault

    DEF pressure line heater relay fault.· Other
    Check soon

    Causes

    • DEF pressure line heater relay or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the DEF pressure line heater relay and look for a value that is stuck or implausible
    2. 2Check the DEF pressure line heater relay connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P20C0-15DEF pressure line heater driver short to battery

    DEF pressure line heater driver short to battery.· Shorted high
    Check soon

    Causes

    • Wire for the DEF pressure line heater driver short to battery touching a battery-fed wire in the harness
    • Water or damage inside the DEF pressure line heater driver short to battery connector bridging to supply

    Checks

    1. 1Unplug the DEF pressure line heater driver short to battery and check the signal wire for voltage with the key on, any battery voltage means a short to supply
    2. 2Inspect the harness for chafing where it crosses live wires near the DEF pressure line heater driver short to battery
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P20C1-00Suction line heater relay open load

    Suction line heater relay open load.· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the suction line heater relay open load
    • Suction line heater relay open load coil, element or sensor internally open

    Checks

    1. 1Unplug the suction line heater relay open load and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the suction line heater relay open load plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P20C1-13DEF suction line heater open circuit

    DEF suction line heater open circuit.· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the DEF suction line heater
    • DEF suction line heater coil, element or sensor internally open

    Checks

    1. 1Unplug the DEF suction line heater and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the DEF suction line heater plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P20BE-02Pressure line heater temperature sensor fault

    Pressure line heater temperature sensor fault.· Other
    Check soon

    Causes

    • Pressure line heater temperature sensor or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the pressure line heater temperature sensor and look for a value that is stuck or implausible
    2. 2Check the pressure line heater temperature sensor connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P20C2-4BDEF suction line heater driver overtemperature

    DEF suction line heater driver overtemperature.· Real condition
    Check soon

    Causes

    • DEF suction line heater driver overtemperature or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the DEF suction line heater driver overtemperature and look for a value that is stuck or implausible
    2. 2Check the DEF suction line heater driver overtemperature connector and wiring for damage
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JCB P20C3-00DEF suction line heater relay error

    DEF suction line heater relay error.· Other
    Check soon

    Causes

    • DEF suction line heater relay or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the DEF suction line heater relay and look for a value that is stuck or implausible
    2. 2Check the DEF suction line heater relay connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P20C3-14DEF suction line heater relay fault

    DEF suction line heater relay fault.· Other
    Check soon

    Causes

    • DEF suction line heater relay or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the DEF suction line heater relay and look for a value that is stuck or implausible
    2. 2Check the DEF suction line heater relay connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P20BA-4BDEF backflow line heater powerstage overtemperature

    DEF backflow line heater powerstage overtemperature.· Real condition
    Check soon

    Causes

    • DEF backflow line heater powerstage overtemperature or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the DEF backflow line heater powerstage overtemperature and look for a value that is stuck or implausible
    2. 2Check the DEF backflow line heater powerstage overtemperature connector and wiring for damage
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JCB P20BE-4BDEF pressure line heater driver overtemperature

    DEF pressure line heater driver overtemperature.· Real condition
    Check soon

    Causes

    • DEF pressure line heater driver overtemperature or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the DEF pressure line heater driver overtemperature and look for a value that is stuck or implausible
    2. 2Check the DEF pressure line heater driver overtemperature connector and wiring for damage
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JCB P20C4-15DEF suction line heater short to battery

    DEF suction line heater short to battery.· Shorted high
    Check soon

    Causes

    • Wire for the DEF suction line heater short to battery touching a battery-fed wire in the harness
    • Water or damage inside the DEF suction line heater short to battery connector bridging to supply

    Checks

    1. 1Unplug the DEF suction line heater short to battery and check the signal wire for voltage with the key on, any battery voltage means a short to supply
    2. 2Inspect the harness for chafing where it crosses live wires near the DEF suction line heater short to battery
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P20BE-05Pressure line heater temperature fault at cold start

    Pressure line heater temperature fault at cold start.· Other
    Check soon

    Causes

    • Pressure line heater temperature fault at cold start or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the pressure line heater temperature fault at cold start and look for a value that is stuck or implausible
    2. 2Check the pressure line heater temperature fault at cold start connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P20B9-00DEF backflow line heater open circuit

    DEF backflow line heater open circuit.· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the DEF backflow line heater
    • DEF backflow line heater coil, element or sensor internally open

    Checks

    1. 1Unplug the DEF backflow line heater and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the DEF backflow line heater plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P20B9-13DEF backflow line heater powerstage open load

    DEF backflow line heater powerstage open load.· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the DEF backflow line heater powerstage open load
    • DEF backflow line heater powerstage open load coil, element or sensor internally open

    Checks

    1. 1Unplug the DEF backflow line heater powerstage open load and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the DEF backflow line heater powerstage open load plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P20BD-13Pressure line heater relay open load (code 13)

    Pressure line heater relay open load (code 13).· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the pressure line heater relay open load
    • Pressure line heater relay open load coil, element or sensor internally open

    Checks

    1. 1Unplug the pressure line heater relay open load and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the pressure line heater relay open load plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P20BE-13DEF pressure line heater relay short to battery

    DEF pressure line heater relay short to battery.· Shorted high
    Check soon

    Causes

    • Wire for the DEF pressure line heater relay short to battery touching a battery-fed wire in the harness
    • Water or damage inside the DEF pressure line heater relay short to battery connector bridging to supply

    Checks

    1. 1Unplug the DEF pressure line heater relay short to battery and check the signal wire for voltage with the key on, any battery voltage means a short to supply
    2. 2Inspect the harness for chafing where it crosses live wires near the DEF pressure line heater relay short to battery
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P20BB-14DEF backflow line heater short to ground

    DEF backflow line heater short to ground.· Shorted low
    Check soon

    Causes

    • Wire for the DEF backflow line heater short to ground chafed and touching chassis or engine ground
    • DEF backflow line heater short to ground coil or sensor shorted internally

    Checks

    1. 1Unplug the DEF backflow line heater short to ground and check each wire for a short to chassis ground
    2. 2Measure the resistance of the DEF backflow line heater short to ground and compare it with the manual value
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P20BF-14DEF pressure line heater short to ground

    DEF pressure line heater short to ground.· Shorted low
    Check soon

    Causes

    • Wire for the DEF pressure line heater short to ground chafed and touching chassis or engine ground
    • DEF pressure line heater short to ground coil or sensor shorted internally

    Checks

    1. 1Unplug the DEF pressure line heater short to ground and check each wire for a short to chassis ground
    2. 2Measure the resistance of the DEF pressure line heater short to ground and compare it with the manual value
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P20BC-15DEF backflow line heater short to battery

    DEF backflow line heater short to battery.· Shorted high
    Check soon

    Causes

    • Wire for the DEF backflow line heater short to battery touching a battery-fed wire in the harness
    • Water or damage inside the DEF backflow line heater short to battery connector bridging to supply

    Checks

    1. 1Unplug the DEF backflow line heater short to battery and check the signal wire for voltage with the key on, any battery voltage means a short to supply
    2. 2Inspect the harness for chafing where it crosses live wires near the DEF backflow line heater short to battery
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P20BE-93DEF pressure line afterrun fault

    DEF pressure line afterrun fault.· Other
    Check soon

    Causes

    • DEF pressure line afterrun or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the DEF pressure line afterrun and look for a value that is stuck or implausible
    2. 2Check the DEF pressure line afterrun connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Measure the resistance of the affected line heater at its plug and compare it with the other lines
  2. 2Check which line the code names (backflow, pressure or suction) and trace that heater harness for chafing
  3. 3Swap the heater relay with a known good one and see if the code follows
  4. 4Check the line temperature sensor reading against the real line temperature after a cold soak

Causes

  • Heater wire in a line open or burnt out
  • Line heater relay failed or its output shorted
  • Line temperature sensor reading wrongly so the heater is held off
  • Heater connector pulled apart where the hose bends

Most common here: open circuit (6 of 23)

Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

When to stop

You'll notice: A DEF warning may show on cold mornings and the SCR system may refuse to dose until the line has thawed.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.