EF Logo

JCB · Transmission control (TCU)

JCB Transmission drive outputs, brake accumulator and transmission temperature fault codes

The transmission controller drives the forward, reverse and gear solenoids on the powershift gearbox, and watches the direction switch. After a solenoid fault it may disable some speeds so the machine can still be moved safely.

More about these parts

The brake accumulator stores pressure for the brakes and a sensor reads it.

FaultCheckC132AJCB · Transmission drive outputs, brake accumulator and transmission temperature
Code shows hereFAULTC132A

Where this code shows

Switch the key on and note any warning lamp or fault icon on the cluster.

What do these codes mean?

JCB codes C132A to P2732-13 are all about the transmission drive outputs, brake accumulator and transmission temperature. The most common failure type is open circuit (3 of 15); 2 need an immediate stop. Start with this check: operate the direction switch and watch the forward and reverse inputs on live data.

How urgent are they?

2 of 15 codes here mean stop now; the other 13 can wait until the shift ends, but find the cause before the next one.

  • Stop now2
  • Check soon13

What should I check first?

Operate the direction switch and watch the forward and reverse inputs on live data

Shared checks

15 of 15

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • JCB C132AForward drive output short circuit

    The controller found the forward drive solenoid output shorted, drawing too much current or sitting at ground or supply, and it switched the output off to protect itself.· Short circuit
    Check soon

    Causes

    • Forward clutch solenoid windings shorted turn to turn, so it pulls excess current
    • Insulation worn off the forward wire where the loom rubs the gearbox casing
    • Transmission oil seeping into the forward solenoid plug and bridging its terminals

    Checks

    1. 1Measure the forward solenoid coil and compare it with the reverse one, looking for a far lower reading
    2. 2Check each forward wire for continuity to chassis earth with the gearbox plug pulled
    3. 3Run a hand along the loom between the gearbox and chassis for flattened or rubbed sections
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.

    Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.

  • JCB C132BReverse drive output open circuit

    The controller sees no current through the reverse drive solenoid output, so the circuit is open.· Open circuit
    Check soon

    Causes

    • Reverse clutch solenoid coil open internally
    • Reverse solenoid terminal loose or backed out at the transmission plug
    • Reverse drive wire broken near the gearbox mount

    Checks

    1. 1Measure reverse solenoid coil resistance at the transmission plug and look for an open circuit
    2. 2With reverse selected and key on, check for drive voltage at the plug
    3. 3Check the reverse drive wire is continuous back to the controller
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB C132CReverse drive output short circuit

    The controller found the reverse drive solenoid output shorted, drawing too much current or sitting at ground or supply, and it switched the output off to protect itself.· Short circuit
    Check soon

    Causes

    • Reverse clutch solenoid winding shorted, so current is too high
    • Reverse wire chafed through where it crosses a transmission bracket and touching earth
    • Oil or washdown water inside the reverse solenoid connector

    Checks

    1. 1Measure the reverse solenoid coil and compare it with the forward one, looking for a far lower reading
    2. 2Check each reverse wire for a short to chassis earth with the transmission plug pulled
    3. 3Trace the loom from the gearbox to the controller for chafed or trapped sections
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.

    Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.

  • JCB P0218Transmission fluid over temperature

    The transmission controller reports that the transmission fluid is too hot.· Lost message
    Stop now

    Causes

    • Low transmission fluid level
    • Transmission oil cooler blocked outside or inside
    • Machine overloaded or working in too high a gear
    • Transmission temperature sensor reading falsely high

    Checks

    1. 1Stop the machine, let the transmission cool and check the fluid level
    2. 2Clean the transmission oil cooler fins and check the cooling fan
    3. 3Compare the displayed temperature with an infrared reading on the housing
    4. 4Check the temperature sensor connector and wiring for corrosion
    5. 5Review how the machine is being used, for example long pushing in a high gear
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB C1321Brake accumulator pressure low

    Brake accumulator pressure has fallen below the safe limit, so braking effort may be reduced.· Other
    Stop now

    Causes

    • Brake charging circuit not keeping up, such as a weak pump or a stuck charging valve
    • Accumulator charge lost or accumulator damaged
    • Brake circuit leaking down the pressure

    Checks

    1. 1Do not drive the machine, and apply the parking brake
    2. 2Check the brake pressure with a gauge and compare it with the display
    3. 3Check the accumulator charge pressure and condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB C1322Forward and reverse inputs both active

    The transmission controller sees forward and reverse selected at the same time, which is not possible from a working shuttle lever.· Other
    Check soon

    Causes

    • Shuttle lever switch contacts stuck closed or shorted together
    • Direction switch wiring shorted between the forward and reverse signal wires
    • Water or dirt in the shuttle lever or steering column switch

    Checks

    1. 1Read the forward and reverse inputs live with the lever in neutral and confirm neither shows active
    2. 2Operate the shuttle lever slowly and watch each input switch cleanly
    3. 3Unplug the lever switch and see if the double input clears
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB C1325Brake accumulator sensor shorted to battery

    Brake accumulator sensor shorted to battery.· Shorted high
    Check soon

    Causes

    • Wire for the brake accumulator sensor shorted to battery touching a battery-fed wire in the harness
    • Water or damage inside the brake accumulator sensor shorted to battery connector bridging to supply

    Checks

    1. 1Unplug the brake accumulator sensor shorted to battery and check the signal wire for voltage with the key on, any battery voltage means a short to supply
    2. 2Inspect the harness for chafing where it crosses live wires near the brake accumulator sensor shorted to battery
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB C1326Brake accumulator sensor shorted to ground

    Brake accumulator sensor shorted to ground.· Shorted low
    Check soon

    Causes

    • Wire for the brake accumulator sensor shorted to ground chafed and touching chassis or engine ground
    • Brake accumulator sensor shorted to ground coil or sensor shorted internally

    Checks

    1. 1Unplug the brake accumulator sensor shorted to ground and check each wire for a short to chassis ground
    2. 2Measure the resistance of the brake accumulator sensor shorted to ground and compare it with the manual value
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB C1329Forward drive output open circuit

    The controller sees no current through the forward drive solenoid output, so the circuit is open.· Open circuit
    Check soon

    Causes

    • Forward clutch solenoid coil burnt open
    • Pin pushed back in the forward solenoid plug on the gearbox
    • Wires torn on the gearbox bracket where the loom is clamped

    Checks

    1. 1Measure forward solenoid coil resistance at the transmission plug and look for an open circuit
    2. 2With the key on and forward selected, probe the solenoid plug for drive voltage from the controller
    3. 3Check the forward drive wire is continuous back to the controller
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB C1350Creep speed disabled due to transmission output fault

    Creep speed disabled due to transmission output fault.· Other
    Check soon

    Causes

    • Creep speed disabled due to transmission output or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the creep speed disabled due to transmission output and look for a value that is stuck or implausible
    2. 2Check the creep speed disabled due to transmission output connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB C1351Slow speed disabled due to transmission output fault

    Slow speed disabled due to transmission output fault.· Other
    Check soon

    Causes

    • Slow speed disabled due to transmission output or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the slow speed disabled due to transmission output and look for a value that is stuck or implausible
    2. 2Check the slow speed disabled due to transmission output connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB C1352Fast speed disabled due to transmission output fault

    Fast speed disabled due to transmission output fault.· Other
    Check soon

    Causes

    • Fast speed disabled due to transmission output or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the fast speed disabled due to transmission output and look for a value that is stuck or implausible
    2. 2Check the fast speed disabled due to transmission output connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB C1353Travel speed disabled due to transmission output fault

    Travel speed disabled due to transmission output fault.· Other
    Check soon

    Causes

    • Travel speed disabled due to transmission output or its wiring faulty
    • Connector corrosion or a loose pin

    Checks

    1. 1Read the live data for the travel speed disabled due to transmission output and look for a value that is stuck or implausible
    2. 2Check the travel speed disabled due to transmission output connector and wiring for damage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB C1354Brake accumulator pressure low at key on

    The controller finds the brake accumulator pressure low when the key is turned on.· Other
    Check soon

    Causes

    • Brake accumulator pressure not yet built after the machine stood for a long time
    • Accumulator nitrogen charge lost
    • Brake charging valve or pump slow to build pressure

    Checks

    1. 1Start the engine and see how long the brake pressure takes to build on the display
    2. 2Check the brake pressure with a gauge at the test point
    3. 3Check the accumulator charge pressure with a testing kit
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P2732-13Y solenoid open circuit

    Y solenoid open circuit.· Open circuit
    Check soon

    Causes

    • Open wire or pushed-back pin between the controller and the Y solenoid
    • Y solenoid coil, element or sensor internally open

    Checks

    1. 1Unplug the Y solenoid and measure across its pins, an open reading means the part is faulty
    2. 2Check continuity of each wire from the Y solenoid plug to the controller pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

Shared checks

Checks, in order

  1. 1Operate the direction switch and watch the forward and reverse inputs on live data
  2. 2Check the brake accumulator pre-charge and the charge circuit for leaks
  3. 3Measure the gearbox solenoid coil resistance at the transmission connector
  4. 4Compare the brake accumulator pressure reading on live data with a known good value
  5. 5Check the gearbox harness for chafing near the bell housing
  6. 6Check the wiring to the brake accumulator pressure for opens, shorts to ground or battery, and chafing
  7. 7Run the transmission output test and confirm each solenoid operates

Causes

  • Forward or reverse solenoid coil failed
  • Accumulator low or charge fault
  • Gearbox harness chafed or its connector flooded
  • Sensor failed

Most common here: open circuit (3 of 15)

Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

When to stop

You'll notice: The machine may not move forward or reverse, may stay in a low gear or may lose a travel speed range.

Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.