JCB · Engine ECU (Dieselmax / Ecomax) - driver controls
JCB Accelerator pedal and driver input switches fault codes
The accelerator pedal has two position sensors so the ECU can check them against each other. These codes report a sensor circuit fault or disagreement between the two.
More about these partsLess
These are the driver input signals to the ECU: the hand throttle, the cruise control switches, the idle speed selector and the vehicle speed sensor. The ECU compares channels and checks that each switch or sensor is in range.
Where this code shows
Switch the key on and note any warning lamp or fault icon on the cluster.
What do these codes mean?
JCB codes P0120 to P2138 are all about the accelerator pedal and driver input switches. The most common failure type is erratic or implausible (10 of 26); none needs an immediate stop. Start with this check: compare the two pedal channels on live data as you press the pedal.
How urgent are they?
None of the 26 codes here means stop now; all 26 can wait until the shift ends, but find the cause before the next one.
- Check soon26
What should I check first?
Compare the two pedal channels on live data as you press the pedal
Shared checks26 of 26
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
JCB P0120Throttle / pedal position sensor A circuit fault
Throttle / pedal position sensor A circuit fault. The controller logged a fault on the throttle / pedal position sensor A circuit, which affects how the accelerator pedal sensors works until the cause is found.· OtherOtherCheck soonCauses
- Throttle / pedal position sensor A circuit or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the throttle / pedal position sensor A circuit and look for a value that is stuck or implausible
- 2Check the throttle / pedal position sensor A circuit connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0121Throttle / pedal position sensor A range/performance
Throttle / pedal position sensor A range/performance. The controller sees the throttle / pedal position sensor A range/performance behaving outside what it expects, so it logs a range, plausibility or performance fault.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Throttle / pedal position sensor A range/performance drifting or worn so it no longer matches the real condition
- Poor connection or high resistance in the throttle / pedal position sensor A range/performance circuit
- A related fault elsewhere making this reading look wrong
Checks
- 1Compare the throttle / pedal position sensor A range/performance value on live data with a known good value or a reference gauge
- 2Check the throttle / pedal position sensor A range/performance connector and wiring for high resistance and intermittent contact
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0220Throttle pedal sensor circuit B fault
Throttle pedal sensor circuit B fault. The controller logged a fault on the throttle pedal sensor circuit B, which affects how the accelerator pedal sensors works until the cause is found.· OtherOtherCheck soonCauses
- Throttle pedal sensor circuit B or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the throttle pedal sensor circuit B and look for a value that is stuck or implausible
- 2Check the throttle pedal sensor circuit B connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P256AIdle speed sensor or switch circuit fault
Idle speed sensor or switch circuit fault. The controller logged a fault on the idle speed sensor or switch circuit, which affects how the driver input works until the cause is found.· OtherOtherCheck soonCauses
- Idle speed sensor or switch circuit or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the idle speed sensor or switch circuit and look for a value that is stuck or implausible
- 2Check the idle speed sensor or switch circuit connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P256BIdle speed selector sensor or switch range/performance
Idle speed selector sensor or switch range/performance. The controller sees the idle speed selector sensor or switch range/performance behaving outside what it expects, so it logs a range, plausibility or performance fault.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Idle speed selector sensor or switch range/performance drifting or worn so it no longer matches the real condition
- Poor connection or high resistance in the idle speed selector sensor or switch range/performance circuit
- A related fault elsewhere making this reading look wrong
Checks
- 1Compare the idle speed selector sensor or switch range/performance value on live data with a known good value or a reference gauge
- 2Check the idle speed selector sensor or switch range/performance connector and wiring for high resistance and intermittent contact
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P256CIdle speed selector sensor or switch circuit low
Idle speed selector sensor or switch circuit low. The reading or voltage for the idle speed selector sensor or switch is below the allowed range, so the controller treats the signal as unreliable.· OtherOtherCheck soonCauses
- Idle speed selector sensor or switch signal pulled low by a short to ground or an open supply
- Sensor or part failed giving a low reading
Checks
- 1Read the idle speed selector sensor or switch value on live data and compare it with the expected value
- 2Unplug the idle speed selector sensor or switch and check the signal wire for a short to ground and the supply for 5 V
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P256DIdle speed selector sensor or switch circuit high
Idle speed selector sensor or switch circuit high. The reading or voltage for the idle speed selector sensor or switch is above the allowed range, so the controller treats the signal as unreliable.· OtherOtherCheck soonCauses
- Idle speed selector sensor or switch signal pulled high by a short to the 5 V reference or supply
- Sensor or part failed giving a high reading
Checks
- 1Read the idle speed selector sensor or switch value on live data and compare it with the expected value
- 2Unplug the idle speed selector sensor or switch and check the signal wire for a short to 5 V or battery
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P0501Vehicle speed sensor A range/performance
Vehicle speed sensor A range/performance. The controller sees the vehicle speed sensor A range/performance behaving outside what it expects, so it logs a range, plausibility or performance fault.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Vehicle speed sensor A range/performance drifting or worn so it no longer matches the real condition
- Poor connection or high resistance in the vehicle speed sensor A range/performance circuit
- A related fault elsewhere making this reading look wrong
Checks
- 1Compare the vehicle speed sensor A range/performance value on live data with a known good value or a reference gauge
- 2Check the vehicle speed sensor A range/performance connector and wiring for high resistance and intermittent contact
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0503Vehicle speed sensor A intermittent or unstable signal
Vehicle speed sensor A intermittent or unstable signal. The controller logged a fault on the vehicle speed sensor A intermittent or unstable signal, which affects how the driver input works until the cause is found.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Vehicle speed sensor A intermittent or unstable signal or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the vehicle speed sensor A intermittent or unstable signal and look for a value that is stuck or implausible
- 2Check the vehicle speed sensor A intermittent or unstable signal connector and wiring for damage
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0566Cruise control off signal fault
Cruise control off signal fault. The controller logged a fault on the cruise control off signal, which affects how the driver input works until the cause is found.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Cruise control off signal or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the cruise control off signal and look for a value that is stuck or implausible
- 2Check the cruise control off signal connector and wiring for damage
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0567Cruise control resume signal fault
Cruise control resume signal fault. The controller logged a fault on the cruise control resume signal, which affects how the driver input works until the cause is found.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Cruise control resume signal or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the cruise control resume signal and look for a value that is stuck or implausible
- 2Check the cruise control resume signal connector and wiring for damage
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0569Cruise control coast signal fault
Cruise control coast signal fault. The controller logged a fault on the cruise control coast signal, which affects how the driver input works until the cause is found.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Cruise control coast signal or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the cruise control coast signal and look for a value that is stuck or implausible
- 2Check the cruise control coast signal connector and wiring for damage
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0570Cruise control accelerate signal fault
Cruise control accelerate signal fault. The controller logged a fault on the cruise control accelerate signal, which affects how the driver input works until the cause is found.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Cruise control accelerate signal or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the cruise control accelerate signal and look for a value that is stuck or implausible
- 2Check the cruise control accelerate signal connector and wiring for damage
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P0575Cruise control input circuit fault
Cruise control input circuit fault. The controller logged a fault on the cruise control input circuit, which affects how the driver input works until the cause is found.· OtherOtherCheck soonCauses
- Cruise control input circuit or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the cruise control input circuit and look for a value that is stuck or implausible
- 2Check the cruise control input circuit connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P1500Faulty foot pedal, emergency mode of movement
Faulty foot pedal, emergency mode of movement. The controller logged a fault on the faulty foot pedal, which affects how the accelerator pedal sensors works until the cause is found.· OtherOtherCheck soonCauses
- Faulty foot pedal or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the faulty foot pedal and look for a value that is stuck or implausible
- 2Check the faulty foot pedal connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P1501Foot pedal failure, low torque
Foot pedal failure, low torque. The reading or voltage for the foot pedal failure is below the allowed range, so the controller treats the signal as unreliable.· OtherOtherCheck soonCauses
- Foot pedal failure signal pulled low by a short to ground or an open supply
- Sensor or part failed giving a low reading
Checks
- 1Read the foot pedal failure value on live data and compare it with the expected value
- 2Unplug the foot pedal failure and check the signal wire for a short to ground and the supply for 5 V
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P1503Hand throttle position signal fault
Hand throttle position signal fault. The controller logged a fault on the hand throttle position signal, which affects how the driver input works until the cause is found.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Hand throttle position signal or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the hand throttle position signal and look for a value that is stuck or implausible
- 2Check the hand throttle position signal connector and wiring for damage
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
JCB P1504Manual throttle malfunction, low torque
Manual throttle malfunction, low torque. The reading or voltage for the manual throttle malfunction is below the allowed range, so the controller treats the signal as unreliable.· OtherOtherCheck soonCauses
- Manual throttle malfunction signal pulled low by a short to ground or an open supply
- Sensor or part failed giving a low reading
Checks
- 1Read the manual throttle malfunction value on live data and compare it with the expected value
- 2Unplug the manual throttle malfunction and check the signal wire for a short to ground and the supply for 5 V
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P1506Throttle / pedal global failure, emergency travel mode
Throttle / pedal global failure, emergency travel mode. The controller logged a fault on the throttle / pedal global failure, which affects how the accelerator pedal sensors works until the cause is found.· OtherOtherCheck soonCauses
- Throttle / pedal global failure or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the throttle / pedal global failure and look for a value that is stuck or implausible
- 2Check the throttle / pedal global failure connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P2120Hand pedal signal channel 1 fault
Hand pedal signal channel 1 fault. The controller logged a fault on the hand pedal signal channel 1, which affects how the driver input works until the cause is found.· OtherOtherCheck soonCauses
- Hand pedal signal channel 1 or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the hand pedal signal channel 1 and look for a value that is stuck or implausible
- 2Check the hand pedal signal channel 1 connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P2122Accelerator sensor 1 low voltage
Accelerator sensor 1 low voltage. The reading or voltage for the accelerator sensor 1 is below the allowed range, so the controller treats the signal as unreliable.· Shorted lowShorted lowCheck soonCauses
- Accelerator sensor 1 signal pulled low by a short to ground or an open supply
- Sensor or part failed giving a low reading
Checks
- 1Read the accelerator sensor 1 value on live data and compare it with the expected value
- 2Unplug the accelerator sensor 1 and check the signal wire for a short to ground and the supply for 5 V
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JCB P2123Accelerator sensor 1 high voltage
Accelerator sensor 1 high voltage. The reading or voltage for the accelerator sensor 1 is above the allowed range, so the controller treats the signal as unreliable.· Shorted highShorted highCheck soonCauses
- Accelerator sensor 1 signal pulled high by a short to the 5 V reference or supply
- Sensor or part failed giving a high reading
Checks
- 1Read the accelerator sensor 1 value on live data and compare it with the expected value
- 2Unplug the accelerator sensor 1 and check the signal wire for a short to 5 V or battery
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JCB P2125Hand pedal signal channel 2 malfunction
Hand pedal signal channel 2 malfunction. The controller logged a fault on the hand pedal signal channel 2 malfunction, which affects how the driver input works until the cause is found.· OtherOtherCheck soonCauses
- Hand pedal signal channel 2 malfunction or its wiring faulty
- Connector corrosion or a loose pin
Checks
- 1Read the live data for the hand pedal signal channel 2 malfunction and look for a value that is stuck or implausible
- 2Check the hand pedal signal channel 2 malfunction connector and wiring for damage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
JCB P2127Accelerator sensor 2 low voltage
Accelerator sensor 2 low voltage. The reading or voltage for the accelerator sensor 2 is below the allowed range, so the controller treats the signal as unreliable.· Shorted lowShorted lowCheck soonCauses
- Accelerator sensor 2 signal pulled low by a short to ground or an open supply
- Sensor or part failed giving a low reading
Checks
- 1Read the accelerator sensor 2 value on live data and compare it with the expected value
- 2Unplug the accelerator sensor 2 and check the signal wire for a short to ground and the supply for 5 V
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JCB P2128Accelerator sensor 2 high voltage
Accelerator sensor 2 high voltage. The reading or voltage for the accelerator sensor 2 is above the allowed range, so the controller treats the signal as unreliable.· Shorted highShorted highCheck soonCauses
- Accelerator sensor 2 signal pulled high by a short to the 5 V reference or supply
- Sensor or part failed giving a high reading
Checks
- 1Read the accelerator sensor 2 value on live data and compare it with the expected value
- 2Unplug the accelerator sensor 2 and check the signal wire for a short to 5 V or battery
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JCB P2138Pedal signal correlation fault
Pedal signal correlation fault. The controller sees the pedal signal correlation behaving outside what it expects, so it logs a range, plausibility or performance fault.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Pedal signal correlation drifting or worn so it no longer matches the real condition
- Poor connection or high resistance in the pedal signal correlation circuit
- A related fault elsewhere making this reading look wrong
Checks
- 1Compare the pedal signal correlation value on live data with a known good value or a reference gauge
- 2Check the pedal signal correlation connector and wiring for high resistance and intermittent contact
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Shared checks
Checks, in order
- 1Compare the two pedal channels on live data as you press the pedal
- 2Operate each control and watch the input on live data
- 3Check the sensor connector for corrosion (on the accelerator pedal sensors, with the diagnostic tool and a multimeter)
- 4Check the connector for corrosion (on the driver input, with the diagnostic tool and a multimeter)
- 5Measure supply and signal at the plug against the ECU pin out
- 6Measure supply and signal at the plug (on the driver input, with the diagnostic tool and a multimeter)
- 7Check the pedal for free movement (on the accelerator pedal sensors, with the diagnostic tool and a multimeter)
Causes
- Pedal sensor failed or worn
- Switch or potentiometer worn or stuck
- Wiring open or shorted
- Poor 5 V supply or earth
Most common here: erratic or implausible (10 of 26)
Watch the live value on the service tool while you flex the harness and tap the connector.
When to stop
You'll notice: The engine may rev slowly, be limited to low idle or limp, and a check lamp is on.
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Partao JCB fault code list, page 4 (code table)
- Partao JCB fault code list, page 5 (code table)
- Partao JCB fault code list, page 14 (code table)
- Partao JCB fault code list, page 7 (code table)
- Partao JCB fault code list, page 9 (code table)
- Partao JCB fault code list, page 10 (code table)
- Partao JCB fault code list, page 12 (code table)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
