Bobcat · Engine
Bobcat Fault Code M0613
Engine speed no signal
What does Bobcat code M0613 mean?
The controller is not getting a speed pulse from the engine. The machine may crank but not start, or stall. Urgency: check soon - the machine may derate or limit a function. Check first: unplug the sensor and check the plug for pushed-back pins or corrosion before testing anything else.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Unplug the sensor and check the plug for pushed-back pins or corrosion before testing anything else
Then 3 more checksWhere this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
Checks
0 of 4 done
Causes
- Wrong air gap or damaged tone wheel
- Failed speed sensor
- Debris or metal on the sensor tip
- Broken wire or loose pin in the sensor plug
How it failed
You'll notice: No engine speed signal reaches the controller.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine speed, ECU messages and power derate
- 06-15Engine speed shutdown levelReal conditionStop now
- 06-18Engine speed out of rangeOtherCheck soon
- M0610Engine speed too highReal conditionCheck soon
- M0611Engine speed extremely highReal conditionStop now
- M0613Engine speed no signalOtherCheck soon
- M0615Engine speed shutdownReal conditionStop now
- M0618Engine speed out of rangeOtherCheck soon
- M0634Engine speed invalid dataOtherCheck soon
- M4028Wrong ECU detectedOtherCheck soon
Show the other 11 codesHide the other codes
- 06-10Engine speed highLost messageCheck soon
- 06-11Engine speed extremely highOtherStop now
- 06-13Engine speed no signalOtherCheck soon
- M4228Wrong DCU detectedOtherCheck soon
- M6604ECU no communicationLost messageCheck soon
- M6904DCU no communicationLost messageCheck soon
- M8615Engine speed derate shutdownOtherStop now
- M8625Engine speed derate unresponsiveOtherCheck soon
- M8715Torque derate shutdownOtherStop now
- M8725Torque derate unresponsiveOtherCheck soon
- M9701Turbo prime sequence activeOtherInformation
Other Bobcat codes: Engine
- VPV004-05Fan control P/V (j), current below normal
- VSV004-05Reverse fan S/V (d), current below normal
- VPV004-06Fan control P/V (j), current above normal
- VSV004-06Reverse fan S/V (d), current above normal
- 04-09Engine oil pressure low
- 04-14Engine oil pressure extremely low
- 04-15Engine oil pressure shutdown level
Related on Equipments Finder
Source
Bobcat Service Code List (rev. 10-20, M-Series/R-Series loaders and M-Series excavators)
This source lists M0613 and its meaning. The guidance on this page is general, not taken from it.
The source covers: M-Series loaders S450-S850 and T450-T870.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
