Bobcat · Engine
Bobcat Engine oil pressure, coolant and air temperature fault codes
The engine ECU and the machine controller report oil pressure, coolant temperature, intake air, ambient and exhaust temperature. Codes are either an out-of-range signal from the sensor or a genuine low, high or shutdown-level reading, which is the more serious meaning.
Where this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
What do these codes mean?
Bobcat codes 04-09 to M2910 are all about the engine oil pressure, coolant and air temperature. The most common failure type is real condition (5 of 28); 9 need an immediate stop. Start with this check: check engine oil level and coolant level first; a real low-oil or over-temperature code should never be cleared without finding the cause.
How urgent are they?
9 of 28 codes here mean stop now; the other 19 can wait until the shift ends, but find the cause before the next one.
- Stop now9
- Check soon19
What should I check first?
Check engine oil level and coolant level first; a real low-oil or over-temperature code should never be cleared without finding the cause.
Shared checks28 of 28
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Bobcat 04-09Engine oil pressure low
Oil pressure is under the warning level. Watch it closely and fix it before it reaches shutdown.· OtherOtherCheck soonCauses
- Worn pump or bearings
- Clogged oil filter or relief valve stuck open
- Engine oil level low
- Wrong or diluted oil that is too thin when hot
Checks
- 1Stop on level ground and check the dipstick; low oil is the cause far more often than a failed part
- 2Warm the engine and listen for bearing knock when the code is active; a rattle means a mechanical fault, not a sensor
- 3Inspect the oil cooler lines and the filter base for leaks that bleed pressure away
- 4Fit a mechanical gauge in place of the sender to compare the real pressure at idle and at high speed against the electronic reading
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 04-14Engine oil pressure extremely low
Oil pressure is dangerously low. Stop the engine and find the cause before restarting. Running on can wreck the engine bearings in minutes.· Lost messageLost messageStop nowCauses
- Oil pump drive or pickup screen blocked
- Pressure relief valve stuck open
- Oil pan almost empty from a leak
Checks
- 1Switch off and check the dipstick and the ground under the machine; a puddle or wet engine shows a major leak
- 2Inspect the oil pickup screen in the pan if you can reach it; a blocked screen stops the pump from drawing oil
- 3Check for fuel dilution of the oil; a thin oil with a strong diesel smell cannot hold pressure
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat 04-15Engine oil pressure shutdown level
The engine shut down on low oil pressure. This protects the engine bearings, so do not keep restarting it.· OtherOtherStop nowCauses
- Severe bearing wear
- Failed oil pump or blocked pickup
- Oil pressure sender giving a false low signal
- Low oil level after a leak or overdue top-up
Checks
- 1Check the dipstick first and top up if low, then look underneath for the point where oil has been lost
- 2Inspect all oil lines, the cooler and the filter base for a split that would drop pressure under load
- 3Check the sender wire for chafe where it passes close to the exhaust or a bracket, since a short can make the controller see zero pressure
- 4Examine the removed filter for metal flakes that signal a bearing issue
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 04-21Engine oil pressure out of range high
The engine oil pressure sensor signal reads above its valid electrical range. That usually means a wiring or sensor fault, not a real reading. The oil pressure display and low-pressure protection are unreliable while this is active.· OtherOtherCheck soonCauses
- Water or corrosion bridging pins in the sensor plug
- Oil seepage into the sensor plug
- Signal wire to the engine oil pressure sensor shorted to supply along the engine harness behind the oil filter side of the block
Checks
- 1Unplug the engine oil pressure sensor with the key on; if the controller-side signal wire still shows battery voltage, the harness is shorted to a live wire
- 2With the key on and the engine off, back-probe the signal wire at the engine oil pressure sensor plug; a reading stuck at supply voltage means a short to supply or a sensor failed high
- 3With the key off, check continuity of the engine oil pressure sensor return wire to the controller; an open return makes the signal rise
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 04-22Engine oil pressure out of range low
The engine oil pressure sensor signal reads below its valid electrical range. That usually means a wiring or sensor fault, not a real reading. The oil pressure display and low-pressure protection are unreliable while this is active.· OtherOtherCheck soonCauses
- Engine oil pressure sensor unplugged or its connector backed off
- Signal wire to the engine oil pressure sensor shorted to ground along the engine harness behind the oil filter side of the block
- Oil seepage into the sensor plug
Checks
- 1Unplug the engine oil pressure sensor and check the signal wire to ground with the key off; low resistance means a short to ground in the harness
- 2Check that the engine oil pressure sensor plug is fully seated, latched and has no backed-out pins or green corrosion
- 3Key on and engine off, back-probe the engine oil pressure sensor plug; the 5 V reference wire should be present and the signal should not sit at zero
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 08-10Engine coolant temperature high
Coolant is hotter than normal. Reduce load and let the engine idle to cool while you check the cooling system.· OtherOtherCheck soonCauses
- Radiator or oil cooler core clogged with dirt
- Loose or slipping fan belt
- Low coolant level or a leak
- Thermostat stuck closed
Checks
- 1Check the fan belt tension and the water pump pulley for slip
- 2Inspect the radiator cap seal and spring, since a weak cap lets the coolant boil early
- 3With the engine cool, check the coolant level in the radiator and the overflow bottle and look for leaks
- 4Compare the gauge with an infrared thermometer at the thermostat housing to check the sensor
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 08-11Engine coolant temperature extremely high
The engine coolant temperature is far above its normal level. The controller may reduce power or shut the machine down to protect it.· OtherOtherStop nowCauses
- Serious overheat or overpressure
- Blocked cooler or relief valve
- Sensor reading extremely high
Checks
- 1Stop the machine and let it cool before testing
- 2Verify the real value with a separate gauge or probe
- 3Check cooler, relief valve and airflow for blockage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 08-15Engine coolant temperature shutdown level
The engine was shut down on high coolant temperature. Do not restart it until the cause is found.· OtherOtherStop nowCauses
- Blocked radiator or cooler
- Thermostat stuck closed
- Low coolant or a major leak
- Water pump or belt failure
Checks
- 1Clean the radiator and cooler fins on both sides
- 2Check for an exhaust gas leak into the coolant, shown by bubbles and pressure in the top hose
- 3Wait until the engine is cool, then check the coolant level and top up with the right mix
- 4Test the thermostat in hot water or replace it if it is suspect
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 08-21Engine coolant temperature out of range high
The engine coolant temperature signal is above the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to supply
- Open sensor ground giving a floating high signal
- Sensor failed high
Checks
- 1Check the ground wire of the engine coolant temperature for continuity
- 2Look at the live reading on the display and see if it sits at the top of its scale
- 3Test the signal wire for stray voltage with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 08-22Engine coolant temperature out of range low
The engine coolant temperature signal is below the valid range the controller accepts, so the reading is treated as a sensor or wiring problem rather than a real value.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Open signal wire or missing supply
- Sensor failed low
Checks
- 1Check the supply voltage at the engine coolant temperature plug with the key on
- 2Look at the live reading on the display and see if it sits at the bottom of its scale
- 3Test the signal wire to ground with the plug off
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0409Engine oil pressure too low
The engine oil pressure sensor reads lower than the warning level. Watch it closely and fix it before it reaches shutdown.· Real conditionReal conditionCheck soonCauses
- Clogged oil filter or relief valve stuck open
- Worn pump or bearings
- Failing sensor reading lower than the real pressure
- Wrong or diluted oil that is too thin when hot
Checks
- 1Look at the oil on the dipstick for fuel or coolant smell and thin, watery colour, which would explain low pressure
- 2Check the sensor plug for oil seepage that could be shorting the circuit and faking a low reading
- 3Check the oil filter date and replace it if it is overdue or if a fresh filter has not been fitted since the last service
- 4Compare the reading cold and hot; pressure that falls sharply once warm suggests worn bearings or an oil that has thinned
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat M0414Engine oil pressure extremely low
Oil pressure is dangerously low. Stop the engine and find the cause before restarting. Stop the engine and find the cause before restarting.· OtherOtherStop nowCauses
- Oil pump drive or pickup screen blocked
- Pressure relief valve stuck open
- Oil line or filter base blown off
Checks
- 1Remove the oil filter and check for debris or metal; metal in the element means the engine is already wearing internally
- 2Disconnect the sensor and fit a mechanical gauge to the sender port, then crank only briefly to see whether pressure builds at all
- 3Check the oil pressure relief valve for a stuck plunger in the pump or block
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0415Engine oil pressure shutdown
The controller has shut the engine down on very low oil pressure to prevent bearing damage.· OtherOtherStop nowCauses
- Severe bearing wear
- Failed oil pump or blocked pickup
- Burst oil line or loose filter
- Oil pressure sender giving a false low signal
Checks
- 1Review the service record for oil type and filter change; the wrong grade or old oil has less film strength when hot
- 2Fit a mechanical gauge in place of the sender; if real pressure is normal at idle the shutdown came from the electrical side
- 3Check the oil pump and its drive for wear or a broken drive key, especially after a hard stall
- 4If pressure is low on the gauge too, repair the engine before any restart and clear the code only after a normal reading
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0421Engine oil pressure out of range high
The oil pressure sensor signal is above its possible range, which usually points to an electrical fault instead of a real pressure reading.· OtherOtherCheck soonCauses
- Oil seepage into the sensor plug
- Internal failure of the engine oil pressure sensor that pegs it high
- Broken return or ground wire at the engine oil pressure sensor
Checks
- 1Check the signal at the engine oil pressure sensor plug with the key on; it should sit within the normal 0.5-4.5 V span and never at full supply
- 2Look at the engine harness behind the oil filter side of the block for chafing against a supply wire and for heat damage
- 3Disconnect the plug and probe the controller-side 5 V reference wire; it should read about 5 V where there is one, and the signal pin should not follow battery voltage
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0422Engine oil pressure out of range low
The oil pressure sensor signal is below its possible range, often from an open or grounded wire.· OtherOtherCheck soonCauses
- Lost 5 V reference wire at the engine oil pressure sensor, or a broken signal wire
- Loose or unplugged engine oil pressure sensor connector
- Failed engine oil pressure sensor reading low
Checks
- 1With the plug removed, a good engine oil pressure sensor signal wire should not read zero ohms to ground; a short means chafed insulation somewhere along the engine harness behind the oil filter side of the block
- 2Look for green corrosion, pushed-back pins or a missing seal inside the engine oil pressure sensor plug
- 3Measure the 5 V reference wire at the unplugged engine oil pressure sensor connector with the key on; no voltage there means an open supply wire or a controller fault
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0810Engine coolant temperature too high
Coolant is hotter than normal. Reduce load and let it idle to cool while you check the cooling system.· Real conditionReal conditionCheck soonCauses
- Thermostat stuck closed
- Low coolant level or a leak
- Cooling fan or shroud damaged
- Loose or slipping fan belt
Checks
- 1Clean the radiator, oil cooler and screen of dirt, chaff and oil film so air can pass
- 2Look for air in the cooling system after a recent refill and bleed it properly
- 3Check the fan shroud and the fan blades for damage that reduce airflow
- 4Check the thermostat; if the top hose is cool while the engine is hot the thermostat is not opening
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat M0811Engine coolant temperature extremely high
The engine is about to overheat. Shut it down once it is safe to do so. The engine is close to overheating, so shut it down once it is safe to do so.· Real conditionReal conditionStop nowCauses
- Radiator fully blocked
- Water pump or belt failure
- Head gasket leaking combustion gas into the coolant
Checks
- 1Check for bubbles in the radiator at idle that show combustion gas in the coolant
- 2Check the fan and belt, and the shroud for damage
- 3Check the thermostat housing and hoses for collapse or swelling
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat M0815Engine coolant temperature shutdown
The controller shut the engine down because coolant temperature reached the protection limit.· OtherOtherStop nowCauses
- Water pump or belt failure
- Thermostat stuck closed
- Blocked radiator or cooler
- Failed temperature sender reading too high
Checks
- 1Inspect hoses, radiator seams and the water pump for leaks and wet spots
- 2Check the belt and fan and the water pump pulley for rotation
- 3Compare the sensor reading against an external thermometer to rule out a bad sender
- 4Run the engine and watch the temperature climb and level off; if it still rises, there is a real cooling fault
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M0821Engine coolant temperature out of range high
The coolant temperature sensor signal is above its allowed electrical range. That usually means a wiring or sensor fault, not a real reading. Overheat protection is unreliable while this is active.· Real conditionReal conditionCheck soonCauses
- Broken return or ground wire at the engine coolant temperature sensor
- Internal failure of the engine coolant temperature sensor that pegs it high
- Short to supply or to the coolant sensor supply and return from the controller on the signal wire at the engine coolant temperature sensor plug
Checks
- 1Look at the engine harness near the thermostat housing for chafing against a supply wire and for heat damage
- 2Disconnect the plug and probe the controller-side coolant sensor supply and return from the controller; it should read about 5 V where there is one, and the signal pin should not follow battery voltage
- 3Check the coolant sensor thread for seepage and the wire for hard, brittle insulation caused by engine heat; a wet thread also points at a leaking seal that lets coolant reach the plug
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat M0822Engine coolant temperature out of range low
The coolant temperature sensor signal is below its allowed electrical range. That usually means a wiring or sensor fault, not a real reading. Overheat protection is unreliable while this is active.· Real conditionReal conditionCheck soonCauses
- Coolant seeping at the sensor thread
- Loose or unplugged engine coolant temperature sensor connector
- Signal wire grounded where the harness runs through the engine harness near the thermostat housing
Checks
- 1With the plug removed, a good engine coolant temperature sensor signal wire should not read zero ohms to ground; a short means chafed insulation somewhere along the engine harness near the thermostat housing
- 2Look for green corrosion, pushed-back pins or a missing seal inside the engine coolant temperature sensor plug
- 3Measure the coolant sensor supply and return from the controller at the unplugged engine coolant temperature sensor connector with the key on; no voltage there means an open supply wire or a controller fault
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Bobcat M0826Engine coolant temperature pre shutdown
The engine coolant temperature has reached the pre-shutdown level, one step before the controller cuts power. Reduce load and look for the cause now. The list gives the same code a different name on M-Series excavators: "Engine coolant temp out of range low".· OtherOtherCheck soonCauses
- Cooling or flow problem getting worse
- Blocked cooler or low fluid
- Sensor reading high
Checks
- 1Reduce load and let the machine cool
- 2Check cooler, fluid level and airflow
- 3Verify the real value with a separate gauge
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M1210Air inlet temperature high
Intake air is hotter than normal, which cuts power and can lead to a derate. It cuts power and can lead to a derate.· Lost messageLost messageCheck soonCauses
- Hot air recirculating from the engine bay
- Damaged hose to the cooler leaking boost
- Missing air baffles
Checks
- 1Check hoses and clamps between the turbo and cooler for leaks that cause a drop in boost and a rise in temperature
- 2Check that the air inlet temperature sensor is seated and not touching a hot component
- 3Check the air inlet path for a sunbaked rubber boot that has cracked and let hot air in
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Bobcat M1211Air inlet temperature extremely high
Intake air temperature is extremely high. Stop and cool the machine. Stop and cool the machine.· OtherOtherStop nowCauses
- Leaking boost pipe or hose
- Turbo overheating
- Severe lack of cooling airflow
Checks
- 1Inspect the cooler core inside and out for oil or dirt that blocks heat transfer
- 2Inspect the turbo outlet for heat discoloration that suggests it has been overheating
- 3Check for fan or belt failure that cuts the airflow through the stack
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M1910Engine ambient temperature high
The sensor measuring air temperature around the engine reads high. The sensor measures air temperature around the engine.· OtherOtherCheck soonCauses
- Cooling fan flow reduced
- Exhaust leak heating the bay
- Sensor near a hot component
Checks
- 1Check that all engine bay covers and baffles are fitted so cooling air takes the right path
- 2Look at the exhaust manifold and turbo joints for a leak that blows hot gas into the bay
- 3Compare the display reading with an infrared thermometer in the engine bay
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M1911Engine ambient temperature extremely high
Engine bay air temperature is extremely high. Engine bay air temperature is extremely high.· OtherOtherCheck soonCauses
- Sensor failing high
- Missing heat shields
- Fire debris or oil build-up near the exhaust
Checks
- 1Check the exhaust manifold, turbo and pipe joints for soot streaks that show a leak
- 2Check the cooler stack and fan for blockage or damage
- 3Compare the sensor reading with a handheld temperature reading on the engine bay air
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M1921Engine ambient temperature out of range high
The engine ambient temperature sensor signal reads above its valid electrical range. That usually means a wiring or sensor fault, not a real reading. Engine bay temperature protection is unreliable while this is active.· OtherOtherCheck soonCauses
- Short to supply or to the engine bay sensor supply from the controller on the signal wire at the engine ambient temperature sensor plug
- Heat damage to the sensor lead in the engine bay
- Broken return or ground wire at the engine ambient temperature sensor
Checks
- 1Look at the engine bay harness near the exhaust side for chafing against a supply wire and for heat damage
- 2Disconnect the plug and probe the controller-side engine bay sensor supply from the controller; it should read about 5 V where there is one, and the signal pin should not follow battery voltage
- 3Check the bay sensor lead for brittle, discoloured insulation and make sure the sensor sits where it was fitted, away from the exhaust manifold, since a sensor that has slipped next to a hot part reads wrongly
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M1922Engine ambient temperature out of range low
The engine ambient temperature sensor signal reads below its valid electrical range. That usually means a wiring or sensor fault, not a real reading. Engine bay temperature protection is unreliable while this is active.· OtherOtherCheck soonCauses
- Failed engine ambient temperature sensor reading low
- Signal wire grounded where the harness runs through the engine bay harness near the exhaust side
- Loose or unplugged engine ambient temperature sensor connector
Checks
- 1With the plug removed, a good engine ambient temperature sensor signal wire should not read zero ohms to ground; a short means chafed insulation somewhere along the engine bay harness near the exhaust side
- 2Look for green corrosion, pushed-back pins or a missing seal inside the engine ambient temperature sensor plug
- 3Measure the engine bay sensor supply from the controller at the unplugged engine ambient temperature sensor connector with the key on; no voltage there means an open supply wire or a controller fault
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat M2910Exhaust gas temperature high
The exhaust gas temperature is higher than normal. Reduce load and look for cooling or airflow problems.· OtherOtherCheck soonCauses
- Turbo not producing boost
- Overfuelling
- Exhaust restriction
Checks
- 1Clean the charge air cooler and check the pipes for boost leaks
- 2Compare the temperature reading with an external probe if a test port is available
- 3Check the turbo for shaft play and a loose compressor housing
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Check engine oil level and coolant level first; a real low-oil or over-temperature code should never be cleared without finding the cause.
- 2Compare the service-screen value with an independent reading (an infrared thermometer on the coolant outlet, for example) to separate sensor faults from real conditions.
- 3Unplug the sensor and look for oil, coolant or moisture in the connector; clean and reseat it.
- 4Measure the sensor signal at the plug against the expected 0.5 to 4.5 V range with the key on; a fixed 0 V or 5 V points to short or open wiring.
- 5Check radiator fins, cooling fan operation and belt condition when a temperature code is genuine.
Causes
- Real low oil level, overheated engine or blocked radiator behind a genuine reading
- Sensor connector corroded, loose or contaminated with oil
- Harness damage between the sensor and the controller
- Sensor failed internally and reading out of range
Most common here: real condition (5 of 28)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: An engine warning lamp, a shutdown or power reduction when a real limit is passed, or a wrong gauge reading when the sensor is the fault.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Bobcat Service Code List (rev. 10-20, M-Series/R-Series loaders and M-Series excavators)
- Bobcat S205 Operation & Maintenance Manual, service codes list
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
