Bobcat · Electrical
Bobcat Fault Code M0322
System voltage out of range low
What does Bobcat code M0322 mean?
The controller measured supply voltage below the allowed window, often during cranking or with a bad connection. Urgency: check soon - the machine may derate or limit a function. Check first: look for the power feed running through a worn connector or bulkhead plug along the harness that has heat marks.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Look for the power feed running through a worn connector or bulkhead plug along the harness that has heat marks
Then 3 more checksWhere this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
Checks
0 of 4 done
Causes
- Corroded fuse holder or relay socket in the feed
- Poor controller ground connection
- Weak battery that sags when loads switch on
- Chafed power wire with high resistance
How it failed
You'll notice: The controller measures its own supply voltage under the valid window.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: System, battery, alternator and controller voltage
- M0310System voltage too highShorted highCheck soon
- M0311System voltage extremely highShorted highStop now
- M0314System voltage extremely lowOtherStop now
- W0321Battery voltage out of range highOtherCheck soon
- M0322System voltage out of range lowOtherCheck soon
- W0322Battery voltage out of range lowOtherCheck soon
- U1092-A2Cab controller system voltage lowShorted lowCheck soon
- U1092-A3Cab controller system voltage highShorted highCheck soon
- U1093-A2Battery voltage lowShorted lowCheck soon
Show the other 26 codesHide the other codes
- LOWVLTGLow battery voltageOtherCheck soon
- VRLOWVLTGVery low battery voltageOtherCheck soon
- VAL001-03Alternator potential, voltage above normalShorted highCheck soon
- VAL001-04Alternator potential, voltage below normalShorted lowCheck soon
- 03-09Battery voltage lowShorted lowCheck soon
- 03-10Battery voltage highShorted highCheck soon
- 03-11Battery voltage extremely highShorted highStop now
- 03-14Battery voltage extremely lowShorted lowStop now
- 03-22Battery voltage out of range lowOtherCheck soon
- 32-66Battery voltage out of rangeOtherCheck soon
- U109C-A2Lights controller voltage lowShorted lowCheck soon
- U109C-A3Lights controller voltage highShorted highCheck soon
- M0309System voltage too lowShorted lowCheck soon
- U1093-A3Battery voltage highShorted highCheck soon
- U1097-A2Aux controller system voltage lowShorted lowCheck soon
- U1097-A3Aux controller system voltage highShorted highCheck soon
- U1098-A2Rear auxiliary controller system voltage lowShorted lowCheck soon
- U1098-A3Rear auxiliary controller system voltage highShorted highCheck soon
- C1182-A3Alternator voltage highShorted highCheck soon
- C1190-00System voltage out of range lowOtherCheck soon
- C1195-00System voltage extremely lowOtherStop now
- W3266ACS battery voltage out of rangeOtherCheck soon
- M4109Alternator lowShorted lowCheck soon
- M4110Alternator highShorted highCheck soon
- D7569Drive battery voltage out of range highOtherCheck soon
- D7571Drive battery voltage out of range lowOtherCheck soon
Other Bobcat codes: Electrical
Related on Equipments Finder
Source
Bobcat Service Code List (rev. 10-20, M-Series/R-Series loaders and M-Series excavators)
This source lists M0322 and its meaning. The guidance on this page is general, not taken from it.
The source covers: M-Series loaders (S450-S850, T450-T870) and M-Series excavators (E26-E85).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
