Bobcat · Fuel system
Bobcat Fault Code 14‑03
Fuel shut-off pull solenoid error OFF
What does Bobcat code 14-03 mean?
The fuel pull solenoid is not energised when it should be on, so the engine may not start. Urgency: stop now - shut down and fix before working on. Check first: check the wiring along the engine harness around the shut-off plug where heat and vibration crack the insulation for continuity and for pins pushed back out of their housings.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Check the wiring along the engine harness around the shut-off plug where heat and vibration crack the insulation for continuity and for pins pushed back out of their housings
Then 5 more checksWhere this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
Checks
0 of 6 done
Causes
- Output driver not switching
- Broken wire or loose plug
- Blown fuse on the fuel pull solenoid feed
- Open coil
1 more causeFewer causes
- Vibration fatigue in the wires at the shut-off plug
How it failed
You'll notice: The controller sees the fuel pull solenoid not energised when it has asked for it.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Make the machine safe before you start: on firm level ground, attachments down, key out.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Fuel hold, fuel pull and lift pump circuits
- 13-05Fuel shut-off hold solenoid short to batteryShorted highStop now
- 13-06Fuel shut-off hold solenoid short to groundShorted lowStop now
- 13-07Fuel shut-off solenoid open circuitOpen circuitStop now
- 14-02Fuel shut-off pull solenoid error ONOtherStop now
- 14-03Fuel shut-off pull solenoid error OFFOtherStop now
- P1134-12Fuel lift pump short to batteryShorted highCheck soon
- P1134-13Fuel lift pump open circuitOpen circuitCheck soon
- M1305Fuel hold solenoid short to batteryShorted highStop now
- M1306Fuel hold solenoid short to groundShorted lowStop now
Show the other 13 codesHide the other codes
- M1307Fuel hold solenoid open circuitOpen circuitStop now
- M1402Fuel pull output error onOtherStop now
- M1403Fuel pull output error offOtherStop now
- M1407Fuel pull output open circuitOpen circuitStop now
- M1428Fuel pull output failureOtherStop now
- M2402Fuel pull relay error onOtherCheck soon
- M2403Fuel pull relay error offOtherStop now
- H9202Fuel lift pump output error onShorted highCheck soon
- M9202Fuel lift pump error onShorted highCheck soon
- H9203Fuel lift pump output error offShorted lowCheck soon
- M9203Fuel lift pump error offShorted lowCheck soon
- H9287Fuel lift pump protection time-outLost messageCheck soon
- M9287Fuel pump failure time exceededReal conditionCheck soon
Other Bobcat codes: Fuel system
Related on Equipments Finder
Source
Bobcat S205 Operation & Maintenance Manual, service codes list
This source lists 14-03 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Older Bobcat skid-steer and track loaders using the two-digit service codes (S205 manual, similar models).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
