EF Logo

Bobcat · Operator presence

Bobcat Right joystick and drive pattern switch fault codes

The right joystick works like the left one and also reads the drive pattern switch that selects ISO or H control pattern. Codes cover the axes and grip, detent and handle faults, and the pattern switch being flipped while the machine is operating.

FaultCheckB10BC-F0Bobcat · Right joystick and drive pattern switch
Code shows hereFAULTB10BC-F0

Where this code shows

On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.

What do these codes mean?

Bobcat codes B10BC-F0 to D7573 are all about the right joystick and drive pattern switch. The most common failure type is erratic or implausible (6 of 32); none needs an immediate stop. Start with this check: release the right joystick and check it rests at neutral on the service screen.

How urgent are they?

None of the 32 codes here means stop now; all 32 can wait until the shift ends, but find the cause before the next one.

  • Check soon32

What should I check first?

Release the right joystick and check it rests at neutral on the service screen.

Shared checks

32 of 32

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Bobcat B10BC-F0Drive right input not in neutral

    The controller sees the right input away from neutral when it should be at rest, so that joystick axis does not command a function.· Erratic or implausible
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration
    • Spring weak or broken
    • Operator control held while starting

    Checks

    1. 1Release the control fully and read the right input value on the service screen; it should sit at neutral.
    2. 2Check the linkage and return spring for binding.
    3. 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Bobcat B10B0-00Drive ISO/H pattern switch flipped while operating

    The controller saw the iso h pattern switch changed while the machine was operating, which it does not allow because the control pattern must be set before moving, so the machine will not drive until the pattern is set.· Other
    Check soon

    Causes

    • Switch bumped or changed during operation
    • Switch contact worn so it flickers
    • Wiring fault making the switch read a changing state

    Checks

    1. 1Set the iso h pattern switch firmly to one position and restart to see whether the code clears.
    2. 2Wiggle the switch harness while watching its state on screen.
    3. 3Replace the the pattern switch contacts if it changes state by itself.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat U10C0-49Right joystick base failure

    The controller reports a failure on the right joystick base without saying whether it is open, shorted or stuck, so the controls in the grip stop working.· Other
    Check soon

    Causes

    • Driver damaged by an earlier short or overload
    • Corroded or loose connector at the grip or base connector
    • Intermittent break in the harness
    • Controller output stage failed

    Checks

    1. 1Read the other active codes for the right joystick base; a short or open code beside this one narrows the cause.
    2. 2Reseat the connector at the grip or base connector and clear the code to see whether it returns.
    3. 3Measure voltage at the plug while the output is commanded to see whether the controller drives it at all.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat U10C1-08Right joystick grip message failure

    The controller stopped receiving valid messages from the right joystick grip, so the controls in the grip stop working.· Other
    Check soon

    Causes

    • Data wire chafed or loose
    • Supply to the unit interrupted
    • Unit failed or software mismatch

    Checks

    1. 1Check supply and ground at the right joystick grip connector.
    2. 2Check the message wiring for chafing and bent pins.
    3. 3Update the software through the dealer if a mismatch is suspected.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat U10C1-49Right joystick grip failure

    The controller reports a failure on the right joystick grip without saying whether it is open, shorted or stuck, so the controls in the grip stop working.· Other
    Check soon

    Causes

    • Driver damaged by an earlier short or overload
    • Corroded or loose connector at the grip or base connector
    • Intermittent break in the harness
    • Controller output stage failed

    Checks

    1. 1Read the other active codes for the right joystick grip; a short or open code beside this one narrows the cause.
    2. 2Reseat the connector at the grip or base connector and clear the code to see whether it returns.
    3. 3Measure voltage at the plug while the output is commanded to see whether the controller drives it at all.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat U10C2-49Right joystick failure

    Right joystick failure: same fault as H4028 (the controller reports a general output failure), here on the right joystick.· Other
    Check soon

    Causes

    • Driver damaged by an earlier short or overload
    • Corroded or loose connector

    Checks

    1. 1Read the other active codes for the right joystick and reseat its connector.
    2. 2Test steps: see H4028.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat U10C3-00Right joystick multiple

    Right joystick multiple: same fault as H4048 (two inputs read active at the same time), here on the right joystick.· Other
    Check soon

    Causes

    • Joystick or handle sensor failed
    • Shorted wires between two signal lines

    Checks

    1. 1Release the control and read each axis on the service screen.
    2. 2Test steps: see H4048.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat 32-67Switch flipped while operating

    Switch flipped while operating: same fault as W3267 (the switch changed state while operating), here on the switch.· Other
    Check soon

    Causes

    • Switch bumped or changed during operation
    • Switch contact worn so it flickers

    Checks

    1. 1Set the switch firmly and restart to see whether the code returns.
    2. 2Test steps: see W3267.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat 32-69Control pattern switch flipped while operating

    The controller saw the control pattern switch changed while the machine was operating, which it does not allow because the control pattern must be set before moving, so the machine will not drive until the pattern is set.· Other
    Check soon

    Causes

    • Switch bumped or changed during operation
    • Switch contact worn so it flickers
    • Wiring fault making the switch read a changing state

    Checks

    1. 1Set the control pattern switch firmly to one position and restart to see whether the code clears.
    2. 2Wiggle the switch harness while watching its state on screen.
    3. 3Replace the the pattern switch contacts if it changes state by itself.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat 32-70Right drive handle short to ground

    The controller reads the right drive handle circuit pulled to ground, so it cannot drive the load.· Shorted low
    Check soon

    Causes

    • Wire chafed against the frame or a bracket at the handle connector
    • The handle sensor shorted to its housing
    • Water in the connector or a pin touching the shell

    Checks

    1. 1With the plug off, test the right drive handle output wire to chassis ground; a reading near zero shows a harness short.
    2. 2Measure from each pin of the handle sensor to its body; any continuity means the part itself is shorted.
    3. 3Look for harness sections crushed under clamps or cut by sharp edges at the handle connector.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat 32-71Right drive handle short to battery

    The controller reads the right drive handle circuit tied to battery voltage when it should only be switched by the controller.· Shorted high
    Check soon

    Causes

    • Output wire rubbed through at the handle connector and touching a live supply wire
    • Water or corrosion in the plug bridging a pin to a power pin
    • Controller output stage failed shorted to supply

    Checks

    1. 1Unplug the right drive handle at the handle connector and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
    2. 2Trace the wire back from the handle sensor for chafing next to live supply wires and for melted insulation.
    3. 3Replace the handle sensor only if the wire reads clean and the part itself reads shorted.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat W0176Input selection flipped while operating

    The controller saw the input selection changed while the machine was operating, which it does not allow because the control pattern must be set before moving, so the machine will not drive until the pattern is set.· Other
    Check soon

    Causes

    • Switch bumped or changed during operation
    • Switch contact worn so it flickers
    • Wiring fault making the switch read a changing state

    Checks

    1. 1Set the input selection firmly to one position and restart to see whether the code clears.
    2. 2Wiggle the switch harness while watching its state on screen.
    3. 3Replace the the pattern switch contacts if it changes state by itself.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat B1120-F0Right primary not in neutral

    The controller sees the right primary away from neutral when it should be at rest, so that joystick axis does not command a function.· Erratic or implausible
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration
    • Spring weak or broken
    • Operator control held while starting

    Checks

    1. 1Release the control fully and read the right primary value on the service screen; it should sit at neutral.
    2. 2Check the linkage and return spring for binding.
    3. 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Bobcat B1121-F0Right secondary not in neutral

    The controller sees the right secondary away from neutral when it should be at rest, so that joystick axis does not command a function.· Erratic or implausible
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration
    • Spring weak or broken
    • Operator control held while starting

    Checks

    1. 1Release the control fully and read the right secondary value on the service screen; it should sit at neutral.
    2. 2Check the linkage and return spring for binding.
    3. 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Bobcat B1122-F0Detent not in neutral

    The controller sees the detent away from neutral when it should be at rest, so that joystick axis does not command a function.· Erratic or implausible
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration
    • Spring weak or broken
    • Operator control held while starting

    Checks

    1. 1Release the control fully and read the detent value on the service screen; it should sit at neutral.
    2. 2Check the linkage and return spring for binding.
    3. 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Bobcat H1221Right primary out of range high

    The controller reads the right primary signal above its normal range, which is usually a wire shorted to supply or a sensor that has failed high, so that joystick axis does not command a function.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high
    • Ground wire open so the signal floats high
    • Water in the connector bridging signal to supply

    Checks

    1. 1Unplug the right primary and measure the signal wire with the key on; a high voltage with the sensor removed means a short in the harness.
    2. 2Check the sensor ground at the plug; an open ground drives the signal high.
    3. 3Measure the 5 V reference at the right primary plug to confirm it is not above 5 V.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat H1222Right primary out of range low

    The controller reads the right primary signal below its normal range, typically a wire shorted to ground, an open supply or a sensor failed low, so that joystick axis does not command a function.· Shorted low
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered
    • Sensor failed with its output pinned low
    • Pin backed out of the connector

    Checks

    1. 1Measure the 5 V reference at the right primary plug; no reference means the fault is in the supply wire, not the sensor.
    2. 2Unplug the sensor and measure the signal wire to ground for a short.
    3. 3Check the connector at the right joystick connector under the armrest for a backed-out pin.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat H1224Right primary not in neutral

    Right primary not in neutral: same fault as B1120-F0 (the input reads away from neutral), here on the right primary.· Other
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration

    Checks

    1. 1Release the control and read the right primary value on the service screen.
    2. 2Test steps: see B1120-F0.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat W3267ACS switch flipped while operating

    The controller saw the switch changed while the machine was operating, which it does not allow because the control pattern must be set before moving, so the machine will not drive until the pattern is set.· Other
    Check soon

    Causes

    • Switch bumped or changed during operation
    • Switch contact worn so it flickers
    • Wiring fault making the switch read a changing state

    Checks

    1. 1Set the switch firmly to one position and restart to see whether the code clears.
    2. 2Wiggle the switch harness while watching its state on screen.
    3. 3Replace the the pattern switch contacts if it changes state by itself.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat W4004Right joystick no communication

    The controller has lost communication with the right joystick, so the right joystick or drive handle does not command a function.· Lost message
    Check soon

    Causes

    • Supply or ground to the unit missing
    • Data wire chafed, open or shorted
    • Unit failed or not programmed
    • Connector corroded at the handle connector

    Checks

    1. 1Measure supply and ground at the right joystick connector with the key on.
    2. 2Check the data wires for continuity and shorts, flexing the harness at the handle connector.
    3. 3Reseat the connector and clear the code to see whether communication returns.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Bobcat W4005Right joystick X-axis not in neutral

    The controller sees the right joystick x axis away from neutral when it should be at rest, so that joystick axis does not command a function.· Erratic or implausible
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration
    • Spring weak or broken
    • Operator control held while starting

    Checks

    1. 1Release the control fully and read the right joystick x axis value on the service screen; it should sit at neutral.
    2. 2Check the linkage and return spring for binding.
    3. 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Bobcat D4007Right joystick Y-axis not in neutral

    The controller sees the right joystick y axis away from neutral when it should be at rest, so that joystick axis does not command a function.· Erratic or implausible
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration
    • Spring weak or broken
    • Operator control held while starting

    Checks

    1. 1Release the control fully and read the right joystick y axis value on the service screen; it should sit at neutral.
    2. 2Check the linkage and return spring for binding.
    3. 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Bobcat W4007Right joystick Y-axis not in neutral

    Right joystick Y-axis not in neutral: same fault as D4007 (the input reads away from neutral), here on the right joystick y axis.· Other
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration

    Checks

    1. 1Release the control and read the right joystick y axis value on the service screen.
    2. 2Test steps: see D4007.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat H4013Right joystick grip no communication

    The controller has lost communication with the right joystick grip, so the controls in the grip stop working.· Lost message
    Check soon

    Causes

    • Supply or ground to the unit missing
    • Data wire chafed, open or shorted
    • Unit failed or not programmed
    • Connector corroded at the grip or base connector

    Checks

    1. 1Measure supply and ground at the right joystick grip connector with the key on.
    2. 2Check the data wires for continuity and shorts, flexing the harness at the grip or base connector.
    3. 3Reseat the connector and clear the code to see whether communication returns.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Bobcat H4016Right joystick not connected

    The controller sees an open circuit on the right joystick, so no current can flow through it and the right joystick or drive handle does not command a function.· Open circuit
    Check soon

    Causes

    • Pin backed out of the connector or plug not latched at the handle connector
    • Wire broken inside its insulation near a bend or clamp
    • The handle sensor burnt open or its internal lead broken

    Checks

    1. 1Check that the right joystick connector at the handle connector is fully seated and its lock tab engaged.
    2. 2Measure the resistance of the handle sensor with the plug off; an infinite reading confirms an open.
    3. 3Check continuity of each wire from the right joystick plug back to the controller connector, flexing the harness as you go.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat H4028Right joystick failure

    The controller reports a failure on the right joystick without saying whether it is open, shorted or stuck, so the right joystick or drive handle does not command a function.· Other
    Check soon

    Causes

    • Driver damaged by an earlier short or overload
    • Corroded or loose connector at the handle connector
    • Intermittent break in the harness
    • Controller output stage failed

    Checks

    1. 1Read the other active codes for the right joystick; a short or open code beside this one narrows the cause.
    2. 2Reseat the connector at the handle connector and clear the code to see whether it returns.
    3. 3Measure voltage at the plug while the output is commanded to see whether the controller drives it at all.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat H4048Right joystick multiple

    The controller reports multiple inputs at once on the right joystick, for example two directions active together, which a healthy control cannot do, so the right joystick or drive handle does not command a function.· Other
    Check soon

    Causes

    • Joystick or handle sensor failed
    • Shorted wires between two signal lines
    • Water in the connector

    Checks

    1. 1Release the control and read each axis on the service screen to find which one reads active.
    2. 2Unplug the right joystick connector and inspect the pins for water and bridging.
    3. 3Replace the the handle sensor if two axes read active with the control at rest.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7508Drive right joystick Y-axis not in neutral

    Drive right joystick Y-axis not in neutral: same fault as D4007 (the input reads away from neutral), here on the right joystick y axis.· Other
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration

    Checks

    1. 1Release the control and read the right joystick y axis value on the service screen.
    2. 2Test steps: see D4007.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7509Drive ISO/H pattern switch short to ground or battery

    The controller found the iso h pattern switch circuit shorted to ground or to battery, so it cannot read the input correctly and the machine will not drive until the pattern is set.· Shorted low
    Check soon

    Causes

    • Handle wiring chafed to the frame or to a supply wire
    • Water in the handle connector
    • Handle or switch failed shorted

    Checks

    1. 1Unplug the iso h pattern switch and measure each signal wire to ground and to supply.
    2. 2Check the connector for water and bridging.
    3. 3Replace the the pattern switch contacts if the harness tests clean.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7522Drive right joystick Y-axis out of range high

    The controller reads the right joystick y axis signal above its normal range, which is usually a wire shorted to supply or a sensor that has failed high, so that joystick axis does not command a function.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high
    • Ground wire open so the signal floats high
    • Water in the connector bridging signal to supply

    Checks

    1. 1Unplug the right joystick y axis and measure the signal wire with the key on; a high voltage with the sensor removed means a short in the harness.
    2. 2Check the sensor ground at the plug; an open ground drives the signal high.
    3. 3Measure the 5 V reference at the right joystick y axis plug to confirm it is not above 5 V.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat D7532Drive right joystick Y-axis out of range low

    The controller reads the right joystick y axis signal below its normal range, typically a wire shorted to ground, an open supply or a sensor failed low, so that joystick axis does not command a function.· Shorted low
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered
    • Sensor failed with its output pinned low
    • Pin backed out of the connector

    Checks

    1. 1Measure the 5 V reference at the right joystick y axis plug; no reference means the fault is in the supply wire, not the sensor.
    2. 2Unplug the sensor and measure the signal wire to ground for a short.
    3. 3Check the connector at the right joystick connector under the armrest for a backed-out pin.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat D7573Drive ISO/H pattern switch flipped while operating

    Drive ISO/H pattern switch flipped while operating: same fault as B10B0-00 (the switch changed state while operating), here on the iso h pattern switch.· Other
    Check soon

    Causes

    • Switch bumped or changed during operation
    • Switch contact worn so it flickers

    Checks

    1. 1Set the iso h pattern switch firmly and restart to see whether the code returns.
    2. 2Test steps: see B10B0-00.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Release the right joystick and check it rests at neutral on the service screen.
  2. 2Set the pattern switch firmly to one position, restart, and watch whether the pattern code clears.
  3. 3Check the grip, base and detent connectors for water and corrosion.
  4. 4Measure the pattern switch circuit for a short to ground or battery with the switch plug off.
  5. 5Check the joystick wiring where it leaves the armrest for chafing.

Causes

  • Joystick centring spring or detent not seating in neutral
  • Right joystick grip or base connector corroded
  • Pattern switch moved during operation or its circuit shorted
  • Handle harness shorted to ground or battery

Most common here: erratic or implausible (6 of 32)

Watch the live value on the service tool while you flex the harness and tap the connector.

When to stop

You'll notice: The joystick or a grip function does not respond, or the machine stops and asks for the pattern switch to be set before it will drive.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.