Bobcat · Operator presence
Bobcat Lift and tilt handle, pedal and joystick inputs fault codes
Lift and tilt are commanded by hand handles, foot pedals or the joystick, each read by position sensors. Codes cover sensors out of range, an input that is not in neutral at start-up, short to ground or battery in the handle wiring, handle information errors, and the same faults on ACS and AHC electronic lift controls.
Where this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
What do these codes mean?
Bobcat codes 32-33 to W3268 are all about the lift and tilt handle, pedal and joystick inputs. The most common failure type is shorted high (8 of 47); none needs an immediate stop. Start with this check: release both handles and pedals fully and restart; clear the code and see whether the input reads neutral on the service screen.
How urgent are they?
None of the 47 codes here means stop now; all 47 can wait until the shift ends, but find the cause before the next one.
- Check soon47
What should I check first?
Release both handles and pedals fully and restart; clear the code and see whether the input reads neutral on the service screen.
Shared checks47 of 47
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Bobcat 32-33Tilt handle wiring fault
Tilt handle wiring fault: same fault as W3233 (the controller found a wiring fault), here on the tilt handle.· OtherOtherCheck soonCauses
- Handle or sensor wiring broken inside the cable
- Connector corroded or loose
Checks
- 1Unplug the tilt handle connector and flex the cable while watching the code.
- 2Test steps: see W3233.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 32-35Tilt handle / pedal not in neutral
The controller sees the handle pedal away from neutral when it should be at rest, so the lift or tilt will not enable and stays locked out. A sticking part or a drifting sensor holds it off neutral.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
- Spring weak or broken
- Operator control held while starting
Checks
- 1Release the control fully and read the handle pedal value on the service screen; it should sit at neutral.
- 2Check the linkage and return spring for binding.
- 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Bobcat 32-38Lift handle wiring fault
Lift handle wiring fault: same fault as W3233 (the controller found a wiring fault), here on the lift handle.· OtherOtherCheck soonCauses
- Handle or sensor wiring broken inside the cable
- Connector corroded or loose
Checks
- 1Unplug the lift handle connector and flex the cable while watching the code.
- 2Test steps: see W3233.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 32-40Lift handle / pedal not in neutral
Lift handle / pedal not in neutral: same fault as 32-35 (the input reads away from neutral), here on the lift handle pedal.· OtherOtherCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
Checks
- 1Release the control and read the lift handle pedal value on the service screen.
- 2Test steps: see 32-35.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat 32-53Lift handle / pedal short to ground
Lift handle / pedal short to ground: same fault as W3253 (the circuit reads pulled to ground), here on the lift handle pedal.· Shorted lowShorted lowCheck soonCauses
- Wire chafed against the frame or a bracket
- The handle or pedal sensor shorted to its housing
Checks
- 1Test the lift handle pedal output wire to chassis ground with the plug off.
- 2Test steps: see W3253.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat 32-54Tilt handle / pedal short to ground
Tilt handle / pedal short to ground: same fault as W3253 (the circuit reads pulled to ground), here on the tilt handle pedal.· Shorted lowShorted lowCheck soonCauses
- Wire chafed against the frame or a bracket
- The handle or pedal sensor shorted to its housing
Checks
- 1Test the tilt handle pedal output wire to chassis ground with the plug off.
- 2Test steps: see W3253.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat 32-55Lift handle / pedal short to battery
Lift handle / pedal short to battery: same fault as W3255 (the circuit reads tied to battery voltage), here on the lift handle pedal.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through
- Water or corrosion in the plug bridging a pin to a power pin
Checks
- 1Unplug the lift handle pedal and look for voltage on its output wire with the key on.
- 2Test steps: see W3255.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat 32-56Tilt handle / pedal short to battery
Tilt handle / pedal short to battery: same fault as W3255 (the circuit reads tied to battery voltage), here on the tilt handle pedal.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through
- Water or corrosion in the plug bridging a pin to a power pin
Checks
- 1Unplug the tilt handle pedal and look for voltage on its output wire with the key on.
- 2Test steps: see W3255.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat 32-68Lift handle information error
Lift handle information error: same fault as W3268 (the controller reports a general output failure), here on the lift handle information.· OtherOtherCheck soonCauses
- Driver damaged by an earlier short or overload
- Corroded or loose connector
Checks
- 1Read the other active codes for the lift handle information and reseat its connector.
- 2Test steps: see W3268.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1060-F0Lift pedal not in neutral
The controller sees the pedal away from neutral when it should be at rest, so the lift or tilt will not enable and stays locked out. A sticking part or a drifting sensor holds it off neutral.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
- Spring weak or broken
- Operator control held while starting
Checks
- 1Release the control fully and read the pedal value on the service screen; it should sit at neutral.
- 2Check the linkage and return spring for binding.
- 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Bobcat B1060-93Lift pedal in error
The controller reports a failure on the pedal without saying whether it is open, shorted or stuck, so the lift or tilt will not enable and stays locked out. It is a general output fault rather than one failure mode.· OtherOtherCheck soonCauses
- Driver damaged by an earlier short or overload
- Corroded or loose connector at the handle or pedal connector
- Intermittent break in the harness
- Controller output stage failed
Checks
- 1Read the other active codes for the pedal; a short or open code beside this one narrows the cause.
- 2Reseat the connector at the handle or pedal connector and clear the code to see whether it returns.
- 3Measure voltage at the plug while the output is commanded to see whether the controller drives it at all.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1061-16Lift pedal sensor a out of range low
The controller reads the pedal sensor a position signal below its normal range, typically a wire shorted to ground, an open supply or a sensor failed low, so the lift or tilt loses a valid position signal and the controller stops the function.· Shorted lowShorted lowCheck soonCauses
- Signal wire shorted to ground
- Supply wire to the sensor open or the sensor not powered
- Sensor failed with its output pinned low
- Pin backed out of the connector
Checks
- 1Measure the 5 V reference at the pedal sensor a plug; no reference means the fault is in the supply wire, not the sensor.
- 2Unplug the sensor and measure the signal wire to ground for a short.
- 3Check the connector at the pedal or handle plug for a backed-out pin.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B1061-17Lift pedal sensor a out of range high
The controller reads the pedal sensor a position signal above its normal range, which is usually a wire shorted to supply or a sensor that has failed high, so the lift or tilt loses a valid position signal and the controller stops the function.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V or battery supply
- Sensor failed with its output pinned high
- Ground wire open so the signal floats high
- Water in the connector bridging signal to supply
Checks
- 1Unplug the pedal sensor a and measure the signal wire with the key on; a high voltage with the sensor removed means a short in the harness.
- 2Check the sensor ground at the plug; an open ground drives the signal high.
- 3Measure the 5 V reference at the pedal sensor a plug to confirm it is not above 5 V.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B1062-16Lift pedal position sensor b out of range low
The controller reads the pedal position sensor b position signal below its normal range, typically a wire shorted to ground, an open supply or a sensor failed low, so the lift or tilt loses a valid position signal and the controller stops the function.· Shorted lowShorted lowCheck soonCauses
- Signal wire shorted to ground
- Supply wire to the sensor open or the sensor not powered
- Sensor failed with its output pinned low
- Pin backed out of the connector
Checks
- 1Measure the 5 V reference at the pedal position sensor b plug; no reference means the fault is in the supply wire, not the sensor.
- 2Unplug the sensor and measure the signal wire to ground for a short.
- 3Check the connector at the pedal or handle plug for a backed-out pin.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat B1062-17Lift pedal position sensor b out of range high
The controller reads the pedal position sensor b position signal above its normal range, which is usually a wire shorted to supply or a sensor that has failed high, so the lift or tilt loses a valid position signal and the controller stops the function.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V or battery supply
- Sensor failed with its output pinned high
- Ground wire open so the signal floats high
- Water in the connector bridging signal to supply
Checks
- 1Unplug the pedal position sensor b and measure the signal wire with the key on; a high voltage with the sensor removed means a short in the harness.
- 2Check the sensor ground at the plug; an open ground drives the signal high.
- 3Measure the 5 V reference at the pedal position sensor b plug to confirm it is not above 5 V.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat B1063-00Lift pedal sensor in error
The controller reports a failure on the pedal sensor without saying whether it is open, shorted or stuck, so the lift or tilt loses a valid position signal and the controller stops the function. It is a general output fault rather than one failure mode.· OtherOtherCheck soonCauses
- Driver damaged by an earlier short or overload
- Corroded or loose connector at the pedal or handle plug
- Intermittent break in the harness
- Controller output stage failed
Checks
- 1Read the other active codes for the pedal sensor; a short or open code beside this one narrows the cause.
- 2Reseat the connector at the pedal or handle plug and clear the code to see whether it returns.
- 3Measure voltage at the plug while the output is commanded to see whether the controller drives it at all.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1064-F0Lift joystick not in neutral
The controller sees the joystick away from neutral when it should be at rest, so the lift or tilt will not enable and stays locked out. A sticking part or a drifting sensor holds it off neutral.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
- Spring weak or broken
- Operator control held while starting
Checks
- 1Release the control fully and read the joystick value on the service screen; it should sit at neutral.
- 2Check the linkage and return spring for binding.
- 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Bobcat B1065-F0Lift input not in neutral
The controller sees the input away from neutral when it should be at rest, so the lift or tilt will not enable and stays locked out. A sticking part or a drifting sensor holds it off neutral.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
- Spring weak or broken
- Operator control held while starting
Checks
- 1Release the control fully and read the input value on the service screen; it should sit at neutral.
- 2Check the linkage and return spring for binding.
- 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Bobcat B1070-F0Tilt pedal not in neutral
Tilt pedal not in neutral: same fault as B1060-F0 (the input reads away from neutral), here on the tilt pedal.· OtherOtherCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
Checks
- 1Release the control and read the tilt pedal value on the service screen.
- 2Test steps: see B1060-F0.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1070-09Tilt pedal failure
Tilt pedal failure: same fault as B1060-93 (the controller reports a general output failure), here on the tilt pedal.· OtherOtherCheck soonCauses
- Driver damaged by an earlier short or overload
- Corroded or loose connector
Checks
- 1Read the other active codes for the tilt pedal and reseat its connector.
- 2Test steps: see B1060-93.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1070-93Tilt pedal in error
Tilt pedal in error: same fault as B1060-93 (the controller reports a general output failure), here on the tilt pedal.· OtherOtherCheck soonCauses
- Driver damaged by an earlier short or overload
- Corroded or loose connector
Checks
- 1Read the other active codes for the tilt pedal and reseat its connector.
- 2Test steps: see B1060-93.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1071-16Tilt pedal sensor a out of range low
Tilt pedal sensor a out of range low: same fault as B1061-16 (the signal is below its normal range), here on the tilt pedal sensor a.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Supply wire to the sensor open or the sensor not powered
Checks
- 1Measure the 5 V reference and the signal wire to ground at the tilt pedal sensor a plug.
- 2Test steps: see B1061-16.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1071-17Tilt pedal sensor a out of range high
Tilt pedal sensor a out of range high: same fault as B1061-17 (the signal is above its normal range), here on the tilt pedal sensor a.· OtherOtherCheck soonCauses
- Signal wire shorted to the 5 V or battery supply
- Sensor failed with its output pinned high
Checks
- 1Unplug the tilt pedal sensor a and measure the signal wire for a short to supply.
- 2Test steps: see B1061-17.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1072-16Tilt pedal position sensor b out of range high
Tilt pedal position sensor b out of range high: same fault as B1062-17 (the signal is above its normal range), here on the tilt pedal position sensor b.· OtherOtherCheck soonCauses
- Signal wire shorted to the 5 V or battery supply
- Sensor failed with its output pinned high
Checks
- 1Unplug the tilt pedal position sensor b and measure the signal wire for a short to supply.
- 2Test steps: see B1062-17.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1072-17Tilt pedal position sensor b out of range low
Tilt pedal position sensor b out of range low: same fault as B1062-16 (the signal is below its normal range), here on the tilt pedal position sensor b.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Supply wire to the sensor open or the sensor not powered
Checks
- 1Measure the 5 V reference and the signal wire to ground at the tilt pedal position sensor b plug.
- 2Test steps: see B1062-16.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1073-00Tilt pedal sensor in error
Tilt pedal sensor in error: same fault as B1063-00 (the controller reports a general output failure), here on the tilt pedal sensor.· OtherOtherCheck soonCauses
- Driver damaged by an earlier short or overload
- Corroded or loose connector
Checks
- 1Read the other active codes for the tilt pedal sensor and reseat its connector.
- 2Test steps: see B1063-00.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1074-F0Tilt joystick not in neutral
Tilt joystick not in neutral: same fault as B1064-F0 (the input reads away from neutral), here on the tilt joystick.· OtherOtherCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
Checks
- 1Release the control and read the tilt joystick value on the service screen.
- 2Test steps: see B1064-F0.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat B1075-F0Tilt input not in neutral
Tilt input not in neutral: same fault as B1065-F0 (the input reads away from neutral), here on the tilt input.· OtherOtherCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
Checks
- 1Release the control and read the tilt input value on the service screen.
- 2Test steps: see B1065-F0.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat W2021Lift handle sensor out of range high
The controller reads the handle sensor position signal above its normal range, which is usually a wire shorted to supply or a sensor that has failed high, so the lift or tilt loses a valid position signal and the controller stops the function.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V or battery supply
- Sensor failed with its output pinned high
- Ground wire open so the signal floats high
- Water in the connector bridging signal to supply
Checks
- 1Unplug the handle sensor and measure the signal wire with the key on; a high voltage with the sensor removed means a short in the harness.
- 2Check the sensor ground at the plug; an open ground drives the signal high.
- 3Measure the 5 V reference at the handle sensor plug to confirm it is not above 5 V.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat W2022Lift handle sensor out of range low
The controller reads the handle sensor position signal below its normal range, typically a wire shorted to ground, an open supply or a sensor failed low, so the lift or tilt loses a valid position signal and the controller stops the function.· Shorted lowShorted lowCheck soonCauses
- Signal wire shorted to ground
- Supply wire to the sensor open or the sensor not powered
- Sensor failed with its output pinned low
- Pin backed out of the connector
Checks
- 1Measure the 5 V reference at the handle sensor plug; no reference means the fault is in the supply wire, not the sensor.
- 2Unplug the sensor and measure the signal wire to ground for a short.
- 3Check the connector at the pedal or handle plug for a backed-out pin.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat W2121Lift pedal sensor out of range high
The controller reads the pedal sensor position signal above its normal range, which is usually a wire shorted to supply or a sensor that has failed high, so the lift or tilt loses a valid position signal and the controller stops the function.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to the 5 V or battery supply
- Sensor failed with its output pinned high
- Ground wire open so the signal floats high
- Water in the connector bridging signal to supply
Checks
- 1Unplug the pedal sensor and measure the signal wire with the key on; a high voltage with the sensor removed means a short in the harness.
- 2Check the sensor ground at the plug; an open ground drives the signal high.
- 3Measure the 5 V reference at the pedal sensor plug to confirm it is not above 5 V.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat W2122Lift pedal sensor out of range low
The controller reads the pedal sensor position signal below its normal range, typically a wire shorted to ground, an open supply or a sensor failed low, so the lift or tilt loses a valid position signal and the controller stops the function.· Shorted lowShorted lowCheck soonCauses
- Signal wire shorted to ground
- Supply wire to the sensor open or the sensor not powered
- Sensor failed with its output pinned low
- Pin backed out of the connector
Checks
- 1Measure the 5 V reference at the pedal sensor plug; no reference means the fault is in the supply wire, not the sensor.
- 2Unplug the sensor and measure the signal wire to ground for a short.
- 3Check the connector at the pedal or handle plug for a backed-out pin.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat W2221Tilt handle sensor out of range high
Tilt handle sensor out of range high: same fault as W2021 (the signal is above its normal range), here on the tilt handle sensor.· OtherOtherCheck soonCauses
- Signal wire shorted to the 5 V or battery supply
- Sensor failed with its output pinned high
Checks
- 1Unplug the tilt handle sensor and measure the signal wire for a short to supply.
- 2Test steps: see W2021.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat W2222Tilt handle sensor out of range low
Tilt handle sensor out of range low: same fault as W2022 (the signal is below its normal range), here on the tilt handle sensor.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Supply wire to the sensor open or the sensor not powered
Checks
- 1Measure the 5 V reference and the signal wire to ground at the tilt handle sensor plug.
- 2Test steps: see W2022.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat W2321Tilt pedal sensor out of range high
Tilt pedal sensor out of range high: same fault as W2121 (the signal is above its normal range), here on the tilt pedal sensor.· OtherOtherCheck soonCauses
- Signal wire shorted to the 5 V or battery supply
- Sensor failed with its output pinned high
Checks
- 1Unplug the tilt pedal sensor and measure the signal wire for a short to supply.
- 2Test steps: see W2121.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat W2322Tilt pedal sensor out of range low
Tilt pedal sensor out of range low: same fault as W2122 (the signal is below its normal range), here on the tilt pedal sensor.· OtherOtherCheck soonCauses
- Signal wire shorted to ground
- Supply wire to the sensor open or the sensor not powered
Checks
- 1Measure the 5 V reference and the signal wire to ground at the tilt pedal sensor plug.
- 2Test steps: see W2122.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat W2824Lift input not in neutral
Lift input not in neutral: same fault as B1065-F0 (the input reads away from neutral), here on the lift input.· OtherOtherCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
Checks
- 1Release the control and read the lift input value on the service screen.
- 2Test steps: see B1065-F0.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat W2924Tilt input not in neutral
Tilt input not in neutral: same fault as B1065-F0 (the input reads away from neutral), here on the tilt input.· OtherOtherCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
Checks
- 1Release the control and read the tilt input value on the service screen.
- 2Test steps: see B1065-F0.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat W3233AHC tilt handle wiring fault
The controller found a wiring fault on the handle: the circuit does not behave like a connected, working part, so the lift or tilt will not enable and stays locked out.· OtherOtherCheck soonCauses
- Handle or sensor wiring broken inside the cable
- Connector corroded or loose
- Pin backed out at the handle plug
Checks
- 1Unplug the handle connector and check the pins for corrosion and push-out.
- 2Flex the cable near the handle while watching the service screen for the fault to set and clear.
- 3Measure continuity of each wire from the handle plug to the controller.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat W3235ACS/AHC tilt handle not in neutral
The controller sees the handle away from neutral when it should be at rest, so the lift or tilt will not enable and stays locked out. A sticking part or a drifting sensor holds it off neutral.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
- Spring weak or broken
- Operator control held while starting
Checks
- 1Release the control fully and read the handle value on the service screen; it should sit at neutral.
- 2Check the linkage and return spring for binding.
- 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Bobcat W3238AHC lift handle wiring fault
AHC lift handle wiring fault: same fault as W3233 (the controller found a wiring fault), here on the ahc lift handle.· OtherOtherCheck soonCauses
- Handle or sensor wiring broken inside the cable
- Connector corroded or loose
Checks
- 1Unplug the ahc lift handle connector and flex the cable while watching the code.
- 2Test steps: see W3233.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat W3240ACS/AHC lift handle not in neutral
ACS/AHC lift handle not in neutral: same fault as W3235 (the input reads away from neutral), here on the acs ahc lift handle.· OtherOtherCheck soonCauses
- Part held off neutral by dirt or a bent linkage
- Sensor drifted or out of calibration
Checks
- 1Release the control and read the acs ahc lift handle value on the service screen.
- 2Test steps: see W3235.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Bobcat W3253ACS lift handle/pedal short to ground
The controller reads the handle pedal circuit pulled to ground, so it cannot drive the load. The output is shut off and the lift or tilt will not enable and stays locked out until the short is cleared.· Shorted lowShorted lowCheck soonCauses
- Wire chafed against the frame or a bracket at the handle or pedal connector
- The handle or pedal sensor shorted to its housing
- Water in the connector or a pin touching the shell
Checks
- 1With the plug off, test the handle pedal output wire to chassis ground; a reading near zero shows a harness short.
- 2Measure from each pin of the handle or pedal sensor to its body; any continuity means the part itself is shorted.
- 3Look for harness sections crushed under clamps or cut by sharp edges at the handle or pedal connector.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat W3254ACS tilt handle/pedal short to ground
ACS tilt handle/pedal short to ground: same fault as W3253 (the circuit reads pulled to ground), here on the tilt handle pedal.· Shorted lowShorted lowCheck soonCauses
- Wire chafed against the frame or a bracket
- The handle or pedal sensor shorted to its housing
Checks
- 1Test the tilt handle pedal output wire to chassis ground with the plug off.
- 2Test steps: see W3253.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Bobcat W3255ACS lift handle/pedal short to battery
The controller reads the handle pedal circuit tied to battery voltage when it should only be switched by the controller. It shuts the output off to protect its driver, so the lift or tilt will not enable and stays locked out.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through at the handle or pedal connector and touching a live supply wire
- Water or corrosion in the plug bridging a pin to a power pin
- Controller output stage failed shorted to supply
Checks
- 1Unplug the handle pedal at the handle or pedal connector and check its output wire for voltage with the key on; any voltage with the load removed is a short to supply.
- 2Trace the wire back from the handle or pedal sensor for chafing next to live supply wires and for melted insulation.
- 3Replace the handle or pedal sensor only if the wire reads clean and the part itself reads shorted.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat W3256ACS tilt handle/pedal short to battery
ACS tilt handle/pedal short to battery: same fault as W3255 (the circuit reads tied to battery voltage), here on the tilt handle pedal.· Shorted highShorted highCheck soonCauses
- Output wire rubbed through
- Water or corrosion in the plug bridging a pin to a power pin
Checks
- 1Unplug the tilt handle pedal and look for voltage on its output wire with the key on.
- 2Test steps: see W3255.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Bobcat W3268ACS lift handle information error
The controller reports a failure on the handle information without saying whether it is open, shorted or stuck, so the lift or tilt will not enable and stays locked out. It is a general output fault rather than one failure mode.· OtherOtherCheck soonCauses
- Driver damaged by an earlier short or overload
- Corroded or loose connector at the handle or pedal connector
- Intermittent break in the harness
- Controller output stage failed
Checks
- 1Read the other active codes for the handle information; a short or open code beside this one narrows the cause.
- 2Reseat the connector at the handle or pedal connector and clear the code to see whether it returns.
- 3Measure voltage at the plug while the output is commanded to see whether the controller drives it at all.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Release both handles and pedals fully and restart; clear the code and see whether the input reads neutral on the service screen.
- 2Move each handle and pedal through its range while watching sensor A and sensor B; they should track each other without jumps.
- 3Check the linkage and return spring for binding or debris holding the input off neutral.
- 4Unplug the handle connector and check pins and seals for water and wear.
- 5Measure the sensor supply and ground at the handle plug, then test the signal wires for shorts to ground and battery.
Causes
- Handle or pedal held off neutral by a stuck mat, debris or a bent linkage
- Position sensor worn, misadjusted or out of range
- Handle harness chafed or shorted where it exits the handle
- Controller not receiving a valid second sensor signal
Most common here: shorted high (8 of 47)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: The lift or tilt function will not move, creeps, or locks out until the handle or pedal is returned to neutral; the controller may refuse to enable the hydraulics.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Bobcat Service Code List (rev. 10-20, M-Series/R-Series loaders and M-Series excavators)
- Bobcat S205 Operation & Maintenance Manual, service codes list
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
