EF Logo

Bobcat · Engine controls

Bobcat Throttle sensors, throttle controller and accelerator pedal fault codes

The hand throttle or accelerator pedal uses a primary and a secondary position sensor so the controller can cross-check them, and a throttle controller or encoder sends the request to the engine. Codes cover sensor range faults, disagreement between the two sensors, calibration and the throttle controller itself.

FaultCheckM2899Bobcat · Throttle sensors, throttle controller and accelerator pedal
Code shows hereFAULTM2899

Where this code shows

On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.

What do these codes mean?

Bobcat codes VAL002-05 to VS5003-04 are all about the throttle sensors, throttle controller and accelerator pedal. The most common failure type is part or controller (5 of 14); none needs an immediate stop. Start with this check: move the throttle through its full travel and watch the primary and secondary values on the service screen; they should move together smoothly.

How urgent are they?

None of the 14 codes here means stop now; all 14 can wait until the shift ends, but find the cause before the next one.

  • Check soon14

What should I check first?

Move the throttle through its full travel and watch the primary and secondary values on the service screen; they should move together smoothly.

Shared checks

14 of 14

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Bobcat VAL002-05Accel. pedal switch, current below normal

    The controller measures less current than expected on the accel. pedal switch circuit.· Open circuit
    Check soon

    Causes

    • Broken wire or loose pin at the plug
    • Coil or element failed open
    • Corroded connector adding resistance

    Checks

    1. 1Unplug the accel. pedal switch and measure its coil resistance; open or very high means it has failed
    2. 2Check the plug pins for corrosion and push-out
    3. 3Check wire continuity from the plug to the controller
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat VAL002-06Accel. pedal switch, current above normal

    The controller measures more current than expected on the accel. pedal switch circuit.· Shorted low
    Check soon

    Causes

    • Coil shorted between turns
    • Wire chafed to the frame
    • Controller driver failed

    Checks

    1. 1Measure the accel. pedal switch coil resistance and compare with the same part on a good machine
    2. 2Test the output wire to ground with the plug off
    3. 3Inspect the harness for crush points and rubbed insulation
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat P0225-54Throttle pedal position sensor calibration required

    The throttle pedal position sensor needs calibration.· Part or controller
    Check soon

    Causes

    • Part replaced or disturbed
    • Calibration never run after service
    • Stored values lost

    Checks

    1. 1Run the calibration procedure for the throttle pedal position sensor from the service tool or display
    2. 2Check the sensors move through their full range during calibration
    3. 3Repeat the calibration if the code stays after the first attempt
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Bobcat U1015-62Throttle encoder signal failure

    The controller reports an internal or output failure on the throttle encoder signal.· Other
    Check soon

    Causes

    • Controller output stage damaged
    • Wiring fault that overloads the output
    • Failed part on the circuit

    Checks

    1. 1Check the throttle encoder signal wiring and plug for shorts, corrosion and chafing
    2. 2Test the part itself against its resistance spec on a matching machine
    3. 3If wiring and part are good, suspect the controller output and take it to a dealer
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat M2721Throttle primary sensor out of range high

    The primary throttle sensor signal is above its allowed range.· Other
    Check soon

    Causes

    • Pushed-back pin or wet connector at the sensor
    • Broken return or ground wire at the primary throttle sensor
    • Worn throttle track or wiper

    Checks

    1. 1Check the signal at the primary throttle sensor plug with the key on; it should sit within the normal 0.5-4.5 V span and never at full supply
    2. 2Look at the harness at the throttle pedal or lever assembly for chafing against a supply wire and for heat damage
    3. 3Disconnect the plug and probe the controller-side 5 V reference wire; it should read about 5 V where there is one, and the signal pin should not follow battery voltage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat M2722Throttle primary sensor out of range low

    The primary throttle sensor signal is below its allowed range.· Other
    Check soon

    Causes

    • Lost 5 V reference wire at the primary throttle sensor, or a broken signal wire
    • Worn throttle track or wiper
    • Loose or unplugged primary throttle sensor connector

    Checks

    1. 1With the plug removed, a good primary throttle sensor signal wire should not read zero ohms to ground; a short means chafed insulation somewhere along the harness at the throttle pedal or lever assembly
    2. 2Look for green corrosion, pushed-back pins or a missing seal inside the primary throttle sensor plug
    3. 3Measure the 5 V reference wire at the unplugged primary throttle sensor connector with the key on; no voltage there means an open supply wire or a controller fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat M2821Throttle secondary sensor out of range high

    The secondary (backup) throttle sensor reads above its valid range.· Other
    Check soon

    Causes

    • Broken return or ground wire at the secondary throttle sensor
    • Backup sensor out of step with the primary
    • Internal failure of the secondary throttle sensor that pegs it high

    Checks

    1. 1Check the signal at the secondary throttle sensor plug with the key on; it should sit within the normal 0.5-4.5 V span and never at full supply
    2. 2Look at the harness at the throttle pedal or lever assembly, beside the primary sensor plug for chafing against a supply wire and for heat damage
    3. 3Disconnect the plug and probe the controller-side 5 V reference wire; it should read about 5 V where there is one, and the signal pin should not follow battery voltage
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat M2822Throttle secondary sensor out of range low

    The throttle sensor signal reads below its valid electrical range.· Other
    Check soon

    Causes

    • Backup sensor out of step with the primary
    • Failed secondary throttle sensor reading low
    • Lost 5 V reference wire at the secondary throttle sensor, or a broken signal wire

    Checks

    1. 1With the plug removed, a good secondary throttle sensor signal wire should not read zero ohms to ground; a short means chafed insulation somewhere along the harness at the throttle pedal or lever assembly, beside the primary sensor plug
    2. 2Look for green corrosion, pushed-back pins or a missing seal inside the secondary throttle sensor plug
    3. 3Measure the 5 V reference wire at the unplugged secondary throttle sensor connector with the key on; no voltage there means an open supply wire or a controller fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat M2899Throttle secondary sensor calibration required

    The controller needs the throttle sensors calibrated.· Part or controller
    Check soon

    Causes

    • Calibration data lost
    • Throttle sensor replaced or moved without calibration
    • Throttle linkage out of position
    • Controller replaced or reprogrammed

    Checks

    1. 1Review recent work on the throttle assembly, since moving a sensor changes its calibration
    2. 2Check that both throttle sensors are mounted square and the linkage moves smoothly through its range
    3. 3Run the throttle calibration routine from the service menu with the engine off and the key on
    4. 4If the calibration will not complete, look for companion throttle sensor range codes
    5. 5After calibrating, check that the two sensors agree through the full travel
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Bobcat M3223Throttle controller not calibrated

    The throttle controller needs calibration.· Part or controller
    Check soon

    Causes

    • Part replaced or disturbed
    • Calibration never run after service
    • Stored values lost

    Checks

    1. 1Run the calibration procedure for the throttle controller from the service tool or display
    2. 2Check the sensors move through their full range during calibration
    3. 3Repeat the calibration if the code stays after the first attempt
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Bobcat M3228Throttle controller failure

    The controller reports an internal or output failure on the throttle.· Part or controller
    Check soon

    Causes

    • Controller output stage damaged
    • Wiring fault that overloads the output
    • Failed part on the circuit

    Checks

    1. 1Check the throttle wiring and plug for shorts, corrosion and chafing
    2. 2Test the part itself against its resistance spec on a matching machine
    3. 3If wiring and part are good, suspect the controller output and take it to a dealer
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Bobcat M3299Throttle controller calibration in process

    The controller logged the message "Throttle controller calibration in process".· Part or controller
    Check soon

    Causes

    • Condition the message names is active
    • Wiring or connector problem on the related part
    • Software or programming mismatch

    Checks

    1. 1Read the message in context with any other active code
    2. 2Check the related part and its plug for damage
    3. 3Clear the code and see whether it returns
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Bobcat VS5003-03Accel pedal sensor, voltage above normal

    The signal voltage from the accel pedal sensor is above the normal range.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to a supply wire
    • Open sensor ground
    • Sensor failed

    Checks

    1. 1Check the sensor ground at the accel pedal sensor plug and its continuity back to the controller
    2. 2Test the signal wire for voltage with the plug off
    3. 3Swap in a known good sensor to see if the reading moves back into range
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat VS5003-04Accel pedal sensor, voltage below normal

    The signal voltage from the accel pedal sensor is below the normal range.· Shorted low
    Check soon

    Causes

    • Sensor wire shorted to ground
    • Open sensor supply or ground
    • Sensor failed

    Checks

    1. 1Check the 5 V supply and ground at the accel pedal sensor plug with the key on
    2. 2Test the signal wire to ground with the plug off
    3. 3Compare the reading with a known good sensor or the same input on a matching machine
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Move the throttle through its full travel and watch the primary and secondary values on the service screen; they should move together smoothly.
  2. 2Run the throttle calibration procedure from the service menu after any sensor, pedal or controller replacement.
  3. 3Measure the 5 V reference and ground at the throttle sensor plug with the key on.
  4. 4Check the throttle harness for chafing where it passes the pedal bracket or cab floor.
  5. 5Wiggle the connector with the signal on screen to catch an intermittent contact before replacing the sensor.

Causes

  • Throttle or pedal sensor out of calibration after replacement
  • Sensor connector corroded or pin backed out
  • Primary and secondary signals disagreeing from a worn or broken sensor
  • Throttle controller or encoder lost power or communication

Most common here: part or controller (5 of 14)

Check power and ground at the module connector with the key on, then its fuses.

When to stop

You'll notice: Engine speed does not follow the throttle control, sticks at idle or high idle, or a throttle calibration message appears.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.