Bobcat · Operator presence
Bobcat Fault Code 11‑06
Seat bar sensor short to ground
What does Bobcat code 11-06 mean?
The seat bar sensor circuit is shorted to ground. Lift, tilt and traction may lock out because the controller cannot confirm the operator is seated. Urgency: check soon - the machine may derate or limit a function. Check first: check for a loose ring terminal or ground strap touching the sensor circuit.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check for a loose ring terminal or ground strap touching the sensor circuit
Then 3 more checksWhere this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
Checks
0 of 4 done
Causes
- Sensor wire chafed to the frame or ground
- Moisture in the connector
- Plug or harness pinched at the pivot
- Sensor internal short to ground
How it failed
You'll notice: Lift, tilt and travel may be disabled because the seat bar sensor circuit is shorted to ground.
Shorted lowRead from how the source describes the code
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Seat bar, press to operate, cab door and door lock
2 other codes on this part are also shorted low (M5306, H7903). When they show together, start at the wiring and connector they share.
- C10B0-00Workgroup disabled due to window faultOtherCheck soon
- 11-05Seat bar sensor short to batteryShorted highCheck soon
- 11-06Seat bar sensor short to groundShorted lowCheck soon
- B1080-09Seat bar failureOtherCheck soon
- B1080-16Seat bar out of range lowOtherCheck soon
- B1080-17Seat bar out of range highOtherCheck soon
- B1090-00Door openOtherCheck soon
- B1091-16Door sensor out of range lowOtherCheck soon
- B1095-13Window sensor open circuitOpen circuitCheck soon
Show the other 15 codesHide the other codes
- B1095-16Window sensor out of range lowOtherCheck soon
- B1095-17Window sensor out of range highOtherCheck soon
- B1095-95Window sensor failureOtherCheck soon
- M1121Seat bar sensor out of range highOtherCheck soon
- M1122Seat bar sensor out of range lowOtherCheck soon
- M1128Seat bar sensor failureErratic or implausibleCheck soon
- M5202Press to operate switch error onShorted highCheck soon
- M5221Press to operate switch out of range highOtherCheck soon
- M5222Press to operate switch out of range lowOtherCheck soon
- M5305Press to operate light short to batteryShorted highCheck soon
- M5306Press to operate light short to groundShorted lowCheck soon
- H7902Door unlock error onShorted highCheck soon
- M7902Forestry door closedOtherInformation
- H7903Door unlock error offShorted lowCheck soon
- M7974Door openOtherCheck soon
Other Bobcat codes: Operator presence
Related on Equipments Finder
Source
Bobcat S205 Operation & Maintenance Manual, service codes (flash count table)
This source lists 11-06 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Older Bobcat skid-steer and track loaders using the two-digit service codes (S205 manual, similar models).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
