EF Logo

Bobcat · Drive

Bobcat Drive direction solenoids, swash plates and motor direction fault codes

Each side of the hydrostatic drive has a forward and a reverse solenoid, a swash plate sensor that reports pump stroke, and a motor direction sensor. The drive controller compares the command with the swash plate position and the motor direction.

More about these parts

A code names the side and part and how it failed.

FaultCheckC10C0-F0Bobcat · Drive direction solenoids, swash plates and motor direction
Code shows hereFAULTC10C0-F0

Where this code shows

On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.

What do these codes mean?

Bobcat codes C10C0-F0 to D7592 are all about the drive direction solenoids, swash plates and motor direction. The most common failure type is shorted low (4 of 40); none needs an immediate stop. Start with this check: note the side and direction in the code, then watch swash plate position against joystick command on the service screen.

How urgent are they?

None of the 40 codes here means stop now; all 40 can wait until the shift ends, but find the cause before the next one.

  • Check soon40

What should I check first?

Note the side and direction in the code, then watch swash plate position against joystick command on the service screen.

Shared checks

40 of 40

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Bobcat C10C0-F0Right swash plate not in neutral

    The controller sees the swash plate away from neutral when it should be at rest, so that side drives slowly, creeps or does not move.· Erratic or implausible
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration
    • Spring weak or broken
    • Operator control held while starting

    Checks

    1. 1Release the control fully and read the swash plate value on the service screen; it should sit at neutral.
    2. 2Check the linkage and return spring for binding.
    3. 3Recalibrate the neutral position if the part moves freely but still reads off neutral.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Bobcat C10C0-77Right swash plate commanded position not reachable

    The controller commands a position for the swash plate and the feedback shows it did not get there, so that side drives slowly, creeps or does not move.· Other
    Check soon

    Causes

    • Part sticking from dirty oil
    • Position feedback sensor out of calibration
    • Low pump or charge pressure so the part cannot move
    • Wiring fault on the control or feedback circuit

    Checks

    1. 1Command a movement and watch the swash plate position against the command on the service screen.
    2. 2Check hydraulic oil level and charge pressure before blaming the the swash plate sensor.
    3. 3Run the drive calibration after any the swash plate sensor or sensor replacement.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C10C1-16Right swash plate sensor out of range low

    The controller reads the swash plate sensor swash plate position signal below its normal range, typically a wire shorted to ground, an open supply or a sensor failed low, so that side drives slowly, creeps or does not move.· Shorted low
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered
    • Sensor failed with its output pinned low
    • Pin backed out of the connector

    Checks

    1. 1Measure the 5 V reference at the swash plate sensor plug; no reference means the fault is in the supply wire, not the sensor.
    2. 2Unplug the sensor and measure the signal wire to ground for a short.
    3. 3Check the connector at the pump swash plate sensor plug for a backed-out pin.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat C10C1-17Right swash plate sensor out of range high

    The controller reads the swash plate sensor swash plate position signal above its normal range, which is usually a wire shorted to supply or a sensor that has failed high, so that side drives slowly, creeps or does not move.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high
    • Ground wire open so the signal floats high
    • Water in the connector bridging signal to supply

    Checks

    1. 1Unplug the swash plate sensor and measure the signal wire with the key on; a high voltage with the sensor removed means a short in the harness.
    2. 2Check the sensor ground at the plug; an open ground drives the signal high.
    3. 3Measure the 5 V reference at the swash plate sensor plug to confirm it is not above 5 V.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat C10C5-F0Left swash plate not in neutral

    Left swash plate not in neutral: same fault as C10C0-F0 (the input reads away from neutral), here on the left swash plate.· Other
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration

    Checks

    1. 1Release the control and read the left swash plate value on the service screen.
    2. 2Test steps: see C10C0-F0.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C10C5-77Left swash plate commanded position not reachable

    Left swash plate commanded position not reachable: same fault as C10C0-77 (the commanded position was not reached), here on the left swash plate commanded position.· Other
    Check soon

    Causes

    • Part sticking from dirty oil
    • Position feedback sensor out of calibration

    Checks

    1. 1Command a movement and watch the left swash plate commanded position position follow the command.
    2. 2Test steps: see C10C0-77.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C10C6-16Left swash plate sensor out of range low

    Left swash plate sensor out of range low: same fault as C10C1-16 (the signal is below its normal range), here on the left swash plate sensor.· Other
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered

    Checks

    1. 1Measure the 5 V reference and the signal wire to ground at the left swash plate sensor plug.
    2. 2Test steps: see C10C1-16.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C10C6-17Left swash plate sensor out of range high

    Left swash plate sensor out of range high: same fault as C10C1-17 (the signal is above its normal range), here on the left swash plate sensor.· Other
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high

    Checks

    1. 1Unplug the left swash plate sensor and measure the signal wire for a short to supply.
    2. 2Test steps: see C10C1-17.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C11C0-11Left forward drive solenoid error off

    The controller sees the forward drive solenoid off when it was commanded on, so that side does not drive in that direction.· Shorted low
    Check soon

    Causes

    • Open or grounded output wire
    • The drive solenoid coil failed open
    • Blown fuse or missing supply to the circuit

    Checks

    1. 1Check the fuse and supply to the forward drive solenoid circuit with the key on.
    2. 2Measure the resistance of the drive solenoid coil and look for an open or a short to its body.
    3. 3Command the function and measure voltage at the forward drive solenoid plug; none means a wiring or controller fault.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat C11C0-12Left forward drive solenoid error on

    The controller sees the forward drive solenoid switched on when it was commanded off, so that side keeps driving.· Other
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck closed
    • Controller output stage failed and cannot switch off

    Checks

    1. 1Unplug the forward drive solenoid at the drive pump solenoid connector with the key on; if the controller still reads it on, the fault is in the wiring or controller.
    2. 2Check the output wire for contact with a power wire along its run.
    3. 3Listen and feel for the drive solenoid coil energising while it should be off.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C11C2-11Left reverse drive solenoid error off

    The controller sees the reverse drive solenoid off when it was commanded on, so that side does not drive in that direction.· Shorted low
    Check soon

    Causes

    • Open or grounded output wire
    • The drive solenoid coil failed open
    • Blown fuse or missing supply to the circuit

    Checks

    1. 1Check the fuse and supply to the reverse drive solenoid circuit with the key on.
    2. 2Measure the resistance of the drive solenoid coil and look for an open or a short to its body.
    3. 3Command the function and measure voltage at the reverse drive solenoid plug; none means a wiring or controller fault.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat C11C2-12Left reverse drive solenoid error on

    The controller sees the reverse drive solenoid switched on when it was commanded off, so that side keeps driving.· Other
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck closed
    • Controller output stage failed and cannot switch off

    Checks

    1. 1Unplug the reverse drive solenoid at the drive pump solenoid connector with the key on; if the controller still reads it on, the fault is in the wiring or controller.
    2. 2Check the output wire for contact with a power wire along its run.
    3. 3Listen and feel for the drive solenoid coil energising while it should be off.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C11C4-11Right forward drive solenoid error off

    Right forward drive solenoid error off: same fault as C11C0-11 (the output reads off when it was commanded on), here on the right forward drive solenoid.· Other
    Check soon

    Causes

    • Open or grounded output wire
    • The drive solenoid coil failed open

    Checks

    1. 1Check the fuse and the supply voltage at the right forward drive solenoid plug with the output commanded.
    2. 2Test steps: see C11C0-11.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C11C4-12Right forward drive solenoid error on

    Right forward drive solenoid error on: same fault as C11C0-12 (the output reads on when it should be off), here on the right forward drive solenoid.· Other
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck closed

    Checks

    1. 1Unplug the right forward drive solenoid with the key on and see whether the controller still reads it on.
    2. 2Test steps: see C11C0-12.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C11C6-11Right reverse drive solenoid error off

    Right reverse drive solenoid error off: same fault as C11C2-11 (the output reads off when it was commanded on), here on the right reverse drive solenoid.· Other
    Check soon

    Causes

    • Open or grounded output wire
    • The drive solenoid coil failed open

    Checks

    1. 1Check the fuse and the supply voltage at the right reverse drive solenoid plug with the output commanded.
    2. 2Test steps: see C11C2-11.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C11C6-12Right reverse drive solenoid error on

    Right reverse drive solenoid error on: same fault as C11C2-12 (the output reads on when it should be off), here on the right reverse drive solenoid.· Other
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck closed

    Checks

    1. 1Unplug the right reverse drive solenoid with the key on and see whether the controller still reads it on.
    2. 2Test steps: see C11C2-12.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C1150-13Right drive motor direction open circuit

    The controller sees an open circuit on the drive motor direction, so no current can flow through it and the controller cannot confirm which way that drive motor turns, so drive is limited.· Open circuit
    Check soon

    Causes

    • Pin backed out of the connector or plug not latched at the drive motor direction sensor plug
    • Wire broken inside its insulation near a bend or clamp
    • The direction sensor burnt open or its internal lead broken

    Checks

    1. 1Check that the drive motor direction connector at the drive motor direction sensor plug is fully seated and its lock tab engaged.
    2. 2Measure the resistance of the direction sensor with the plug off; an infinite reading confirms an open.
    3. 3Check continuity of each wire from the drive motor direction plug back to the controller connector, flexing the harness as you go.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat C1150-16Right drive motor direction out of range low

    The controller reads the drive motor direction direction signal below its normal range, typically a wire shorted to ground, an open supply or a sensor failed low, so the controller cannot confirm which way that drive motor turns, so drive is limited.· Shorted low
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered
    • Sensor failed with its output pinned low
    • Pin backed out of the connector

    Checks

    1. 1Measure the 5 V reference at the drive motor direction plug; no reference means the fault is in the supply wire, not the sensor.
    2. 2Unplug the sensor and measure the signal wire to ground for a short.
    3. 3Check the connector at the drive motor direction sensor plug for a backed-out pin.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Bobcat C1150-17Right drive motor direction out of range high

    The controller reads the drive motor direction direction signal above its normal range, which is usually a wire shorted to supply or a sensor that has failed high, so the controller cannot confirm which way that drive motor turns, so drive is limited.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high
    • Ground wire open so the signal floats high
    • Water in the connector bridging signal to supply

    Checks

    1. 1Unplug the drive motor direction and measure the signal wire with the key on; a high voltage with the sensor removed means a short in the harness.
    2. 2Check the sensor ground at the plug; an open ground drives the signal high.
    3. 3Measure the 5 V reference at the drive motor direction plug to confirm it is not above 5 V.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Bobcat C1155-13Left drive motor direction open circuit

    Left drive motor direction open circuit: same fault as C1150-13 (the circuit is open), here on the left drive motor direction.· Open circuit
    Check soon

    Causes

    • Pin backed out of the connector or plug not latched
    • Wire broken inside its insulation

    Checks

    1. 1Check the left drive motor direction connector is seated, then measure across the part for an open.
    2. 2Test steps: see C1150-13.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Bobcat C1155-16Left drive motor direction out of range low

    Left drive motor direction out of range low: same fault as C1150-16 (the signal is below its normal range), here on the left drive motor direction.· Other
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered

    Checks

    1. 1Measure the 5 V reference and the signal wire to ground at the left drive motor direction plug.
    2. 2Test steps: see C1150-16.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat C1155-17Left drive motor direction out of range high

    Left drive motor direction out of range high: same fault as C1150-17 (the signal is above its normal range), here on the left drive motor direction.· Other
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high

    Checks

    1. 1Unplug the left drive motor direction and measure the signal wire for a short to supply.
    2. 2Test steps: see C1150-17.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7517Drive left swash plate not in neutral

    Drive left swash plate not in neutral: same fault as C10C0-F0 (the input reads away from neutral), here on the left swash plate.· Other
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration

    Checks

    1. 1Release the control and read the left swash plate value on the service screen.
    2. 2Test steps: see C10C0-F0.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7518Drive right swash plate not in neutral

    Drive right swash plate not in neutral: same fault as C10C0-F0 (the input reads away from neutral), here on the right swash plate.· Other
    Check soon

    Causes

    • Part held off neutral by dirt or a bent linkage
    • Sensor drifted or out of calibration

    Checks

    1. 1Release the control and read the right swash plate value on the service screen.
    2. 2Test steps: see C10C0-F0.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7527Drive left swash plate out of position

    Drive left swash plate out of position: same fault as C10C0-77 (the commanded position was not reached), here on the left swash plate.· Other
    Check soon

    Causes

    • Part sticking from dirty oil
    • Position feedback sensor out of calibration

    Checks

    1. 1Command a movement and watch the left swash plate position follow the command.
    2. 2Test steps: see C10C0-77.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7528Drive right swash plate out of position

    Drive right swash plate out of position: same fault as C10C0-77 (the commanded position was not reached), here on the right swash plate.· Other
    Check soon

    Causes

    • Part sticking from dirty oil
    • Position feedback sensor out of calibration

    Checks

    1. 1Command a movement and watch the right swash plate position follow the command.
    2. 2Test steps: see C10C0-77.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7539Drive left swash plate sensor out of range high

    Drive left swash plate sensor out of range high: same fault as C10C1-17 (the signal is above its normal range), here on the left swash plate sensor.· Other
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high

    Checks

    1. 1Unplug the left swash plate sensor and measure the signal wire for a short to supply.
    2. 2Test steps: see C10C1-17.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7540Drive left swash plate sensor out of range low

    Drive left swash plate sensor out of range low: same fault as C10C1-16 (the signal is below its normal range), here on the left swash plate sensor.· Other
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered

    Checks

    1. 1Measure the 5 V reference and the signal wire to ground at the left swash plate sensor plug.
    2. 2Test steps: see C10C1-16.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7541Drive right swash plate sensor out of range high

    Drive right swash plate sensor out of range high: same fault as C10C1-17 (the signal is above its normal range), here on the right swash plate sensor.· Other
    Check soon

    Causes

    • Signal wire shorted to the 5 V or battery supply
    • Sensor failed with its output pinned high

    Checks

    1. 1Unplug the right swash plate sensor and measure the signal wire for a short to supply.
    2. 2Test steps: see C10C1-17.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7542Drive right swash plate sensor out of range low

    Drive right swash plate sensor out of range low: same fault as C10C1-16 (the signal is below its normal range), here on the right swash plate sensor.· Other
    Check soon

    Causes

    • Signal wire shorted to ground
    • Supply wire to the sensor open or the sensor not powered

    Checks

    1. 1Measure the 5 V reference and the signal wire to ground at the right swash plate sensor plug.
    2. 2Test steps: see C10C1-16.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7543Drive left forward drive solenoid error on

    Drive left forward drive solenoid error on: same fault as C11C0-12 (the output reads on when it should be off), here on the left forward drive solenoid.· Other
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck closed

    Checks

    1. 1Unplug the left forward drive solenoid with the key on and see whether the controller still reads it on.
    2. 2Test steps: see C11C0-12.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7544Drive left reverse drive solenoid error on

    Drive left reverse drive solenoid error on: same fault as C11C2-12 (the output reads on when it should be off), here on the left reverse drive solenoid.· Other
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck closed

    Checks

    1. 1Unplug the left reverse drive solenoid with the key on and see whether the controller still reads it on.
    2. 2Test steps: see C11C2-12.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7545Drive right forward drive solenoid error on

    Drive right forward drive solenoid error on: same fault as C11C0-12 (the output reads on when it should be off), here on the right forward drive solenoid.· Other
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck closed

    Checks

    1. 1Unplug the right forward drive solenoid with the key on and see whether the controller still reads it on.
    2. 2Test steps: see C11C0-12.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7546Drive right reverse drive solenoid error on

    Drive right reverse drive solenoid error on: same fault as C11C2-12 (the output reads on when it should be off), here on the right reverse drive solenoid.· Other
    Check soon

    Causes

    • Output wire shorted to a live supply
    • Relay or driver stuck closed

    Checks

    1. 1Unplug the right reverse drive solenoid with the key on and see whether the controller still reads it on.
    2. 2Test steps: see C11C2-12.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7553Drive left forward drive solenoid error off

    Drive left forward drive solenoid error off: same fault as C11C0-11 (the output reads off when it was commanded on), here on the left forward drive solenoid.· Other
    Check soon

    Causes

    • Open or grounded output wire
    • The drive solenoid coil failed open

    Checks

    1. 1Check the fuse and the supply voltage at the left forward drive solenoid plug with the output commanded.
    2. 2Test steps: see C11C0-11.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7554Drive left reverse drive solenoid error off

    Drive left reverse drive solenoid error off: same fault as C11C2-11 (the output reads off when it was commanded on), here on the left reverse drive solenoid.· Other
    Check soon

    Causes

    • Open or grounded output wire
    • The drive solenoid coil failed open

    Checks

    1. 1Check the fuse and the supply voltage at the left reverse drive solenoid plug with the output commanded.
    2. 2Test steps: see C11C2-11.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7555Drive right forward drive solenoid error off

    Drive right forward drive solenoid error off: same fault as C11C0-11 (the output reads off when it was commanded on), here on the right forward drive solenoid.· Other
    Check soon

    Causes

    • Open or grounded output wire
    • The drive solenoid coil failed open

    Checks

    1. 1Check the fuse and the supply voltage at the right forward drive solenoid plug with the output commanded.
    2. 2Test steps: see C11C0-11.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7556Drive right reverse drive solenoid error off

    Drive right reverse drive solenoid error off: same fault as C11C2-11 (the output reads off when it was commanded on), here on the right reverse drive solenoid.· Other
    Check soon

    Causes

    • Open or grounded output wire
    • The drive solenoid coil failed open

    Checks

    1. 1Check the fuse and the supply voltage at the right reverse drive solenoid plug with the output commanded.
    2. 2Test steps: see C11C2-11.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7591Drive left swashplate sensor reversed

    The swash plate sensor moves the opposite way to the command, so the controller flags inverted movement and that side drives slowly, creeps or does not move.· Other
    Check soon

    Causes

    • Sensor or its wires fitted reversed after a repair
    • Wrong sensor type fitted
    • Calibration done with the sensor reversed

    Checks

    1. 1Command a movement and compare the direction of the swash plate sensor reading with the command.
    2. 2Check the wiring to the swash plate sensor against the schematic for swapped signal and supply wires.
    3. 3Recalibrate after correcting the wiring.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Bobcat D7592Drive right swashplate sensor reversed

    Drive right swashplate sensor reversed: same fault as D7591 (the sensor moves opposite to the command), here on the right swashplate sensor.· Other
    Check soon

    Causes

    • Sensor or its wires fitted reversed after a repair
    • Wrong sensor type fitted

    Checks

    1. 1Command a movement and compare the right swashplate sensor direction with the command.
    2. 2Test steps: see D7591.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Note the side and direction in the code, then watch swash plate position against joystick command on the service screen.
  2. 2Measure the coil resistance of the named drive solenoid with the plug off and compare it with the opposite side.
  3. 3Check the pump and motor connectors for water, corrosion and pushed-back pins.
  4. 4Run the drive pump calibration after replacing a solenoid, sensor or the drive controller.
  5. 5Look at the harness at the rear of the machine for chafing and heat damage near the pumps.

Causes

  • Drive solenoid coil failed open or shorted
  • Swash plate sensor failed, reversed or out of calibration
  • Harness chafed near the pumps at the back of the machine
  • Connector at the pump or motor corroded

Most common here: shorted low (4 of 40)

Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

When to stop

You'll notice: The machine drives slowly or not at all on one side, creeps when the joysticks are in neutral, or pulls to one side.

Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.