Bobcat · Safety interlocks
Bobcat Fault Code M1706
Hydraulic lock valve solenoid short to ground
What does Bobcat code M1706 mean?
The hydraulic lock valve solenoid output is shorted to ground, so the coil will not energise correctly. Lift and tilt, or excavator hydraulics, may lock out. Urgency: check soon - the machine may derate or limit a function. Check first: with the plug off, test the hydraulic lock valve solenoid output wire to chassis ground; a reading near zero shows a harness short to ground.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
With the plug off, test the hydraulic lock valve solenoid output wire to chassis ground; a reading near zero shows a harness short to ground
Then 5 more checksWhere this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
Checks
0 of 6 done
Causes
- Moisture inside the hydraulic lock valve solenoid connector
- Chafed output wire touching the frame on the lift and tilt lock valve at the control valve
- Coil insulation breakdown
- Contamination in the lock valve spool bore
1 more causeFewer causes
- Harness crushed at a bracket or clamp
How it failed
You'll notice: The hydraulic lock valve solenoid output reads grounded, which stops the controller driving the coil.
Shorted lowRead from how the source describes the code
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Traction lock and hydraulic lock solenoids
4 other codes on this part are also shorted low (16-06, 17-06, C1029-11, M1606). When they show together, start at the wiring and connector they share.
- M1606Traction lock hold solenoid short to groundShorted lowCheck soon
- M1607Traction lock hold solenoid open circuitOpen circuitCheck soon
- M1632Hydraulic bypass overcurrentLost messageCheck soon
- M1705Hydraulic lock valve solenoid short to batteryShorted highCheck soon
- M1706Hydraulic lock valve solenoid short to groundShorted lowCheck soon
- M1707Hydraulic lock valve solenoid open circuitOpen circuitCheck soon
- M1732Hydraulic lock valve solenoid overcurrentOtherCheck soon
- M2502Traction pull relay error onOtherCheck soon
- M2503Traction pull relay error offOtherCheck soon
Show the other 16 codesHide the other codes
- 15-02Traction lock pull solenoid error ONOtherCheck soon
- 15-03Traction lock pull solenoid error OFFOtherCheck soon
- 16-05Traction lock hold solenoid short to batteryShorted highCheck soon
- 16-06Traction lock hold solenoid short to groundShorted lowCheck soon
- 16-07Traction lock hold solenoid open circuitOpen circuitCheck soon
- 17-05Hydraulic lock valve solenoid short to batteryShorted highCheck soon
- 17-06Hydraulic lock valve solenoid short to groundShorted lowCheck soon
- 17-07Hydraulic lock valve solenoid open circuitOpen circuitCheck soon
- C1029-11Hydraulic lock solenoid short to groundShorted lowCheck soon
- C1029-12Hydraulic lock solenoid short to batteryShorted highCheck soon
- C1029-13Hydraulic lock solenoid open circuitOpen circuitCheck soon
- M1502Traction lock pull output error onOtherCheck soon
- M1503Traction lock pull output error offOtherCheck soon
- M1507Traction lock pull output open circuitOpen circuitCheck soon
- M1528Traction lock pull output failureOtherCheck soon
- M1605Traction lock hold solenoid short to batteryShorted highCheck soon
Other Bobcat codes: Safety interlocks
Related on Equipments Finder
Source
Bobcat Service Code List (rev. 10-20, M-Series/R-Series loaders and M-Series excavators)
This source lists M1706 and its meaning. The guidance on this page is general, not taken from it.
The source covers: M-Series loaders (S450-S850, T450-T870) and M-Series excavators (E26-E85).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
