JLG · Outputs (valves and coils)
JLG Drive, steer and flow control valves fault codes
The drive forward and reverse valves, the front steer valves and the flow control valve are the coils that move the machine on the ground and set its drive oil flow. The module drives them and watches their current and output state.
Where this code shows
Turn the key on and watch the fault lamp or platform display.
What do these codes mean?
JLG codes 8639 to 33419 are all about the drive, steer and flow control valves. The most common failure type is shorted low (5 of 18); none needs an immediate stop. Start with this check: read the code to see which valve and which failure is named.
How urgent are they?
None of the 18 codes here means stop now; all 18 can wait until the shift ends, but find the cause before the next one.
- Check soon18
What should I check first?
Read the code to see which valve and which failure is named
Shared checks18 of 18
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Front Left Steer Valve3 codes
JLG 8639Front Left Steer Valve: Open circuit
The controller drives the front left steer valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Broken internal lead in the solenoid coil
- Front left steer coil open, so the left wheel cannot be steered and the machine steers one-sided
- Lead stretched or kinked until it broke at the front axle, where the cable flexes as the left wheel steers
- Pin backed out or loose in the connector, because the left steer plug is at the front axle, and the cable flexes with the steering
Checks
- 1Unplug the front left steer valve at the front axle and measure across its two pins; an open reading means a dead solenoid coil
- 2Test between the module pin and the plug section by section, beginning at the front axle, where the cable flexes as the left wheel steers
- 3Try it on the machine: press the steer rocker to the left and listen for the click at the axle, then see whether the left wheel turns
- 4Steer to the other side: if the right wheel turns the steer circuit is alive and only the left coil is open
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 8640Front Left Steer Valve: Short to battery
The controller reads battery voltage on the front left steer valve output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Two harness legs bundled so tightly that a worn spot joins them
- Front left steer wire touching a feed at the axle so the left wheel may turn on its own
- Melted insulation at the front axle, where the cable flexes as the left wheel steers
- Corrosion between pins in the plug (the left steer plug is at the front axle, and the cable flexes with the steering)
Checks
- 1With the load off at the front axle and the key on, any reading on the output wire is the short
- 2Feel along the harness at the front axle, where the cable flexes as the left wheel steers for scuffed, hard or discoloured insulation
- 3Press the steer rocker to the left and listen for the click at the axle, then see whether the left wheel turns; battery voltage should appear on the output only when it is commanded on
- 4Watch the left wheel with the rocker centred; turning means the output is held on
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JLG 8641Front Left Steer Valve: Short to ground
The controller sees the front left steer valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Front left steer valve solenoid coil shorted to its case
- Front left steer coil shorted by wheel spray and mud at the front axle
- Wire chafed through to the frame at the front axle, where the cable flexes as the left wheel steers
- Dirt and water bridging a pin to ground; the left steer plug is at the front axle, and the cable flexes with the steering
Checks
- 1Disconnect the load at the front axle; the code staying means a harness or module fault
- 2Meter between the signal pin and chassis with the plug apart; a reading shows the earth path, probably at the front axle, where the cable flexes as the left wheel steers
- 3Press the steer rocker to the left and listen for the click at the axle, then see whether the left wheel turns; the analyzer output should go to supply, not stay at zero
- 4Wash and dry the left axle plug before testing, then meter the left coil to its case
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Front Right Steer Valve3 codes
JLG 8642Front Right Steer Valve: Open circuit
The controller drives the front right steer valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Open winding in the coil
- Front right steer coil open, so the right wheel cannot be steered and the machine steers one-sided
- Harness fatigued and parted at the right axle end, where wheel spray and stones reach the harness
- Corroded or open terminal in the plug; the right steer connector is at the front axle and takes the wheel spray
Checks
- 1Read the coil resistance at the connector at the front axle; no reading means a burnt winding
- 2Test both wires with the plug off and flex them at the right axle end, where wheel spray and stones reach the harness to catch a hidden break
- 3Try it on the machine: press the steer rocker to the right, listen for the click and watch the right wheel
- 4Steer to the other side: if the left wheel turns the steer circuit is alive and only the right coil is open
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 8643Front Right Steer Valve: Short to battery
The controller reads battery voltage on the front right steer valve output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Supply leaking onto the output wire through damaged insulation
- Front right steer wire touching a feed at the axle so the right wheel may turn on its own
- Harness rubbed bare and touching a feed at the right axle end, where wheel spray and stones reach the harness
- Bent terminal touching the supply pin, because the right steer connector is at the front axle and takes the wheel spray
Checks
- 1Unplug the load at the front axle and read the signal wire with the key on; it should be zero while off
- 2Inspect the harness for bare spots, burnt insulation and melted clamps, especially at the right axle end, where wheel spray and stones reach the harness
- 3Press the steer rocker to the right, listen for the click and watch the right wheel; battery voltage should appear on the output only when it is commanded on
- 4Watch the right wheel with the rocker centred; turning means the output is held on
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JLG 8644Front Right Steer Valve: Short to ground
The controller sees the front right steer valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Winding broken down to earth
- Front right steer coil shorted by stones and spray at the right axle end
- Earth path from a worn lead at the right axle end, where wheel spray and stones reach the harness
- Green corrosion in the connector (the right steer connector is at the front axle and takes the wheel spray)
Checks
- 1Pull the plug at the front axle and recycle EMS to see whether the code stays
- 2Test the output wire to the chassis with the connector open; any path is the short, most likely at the right axle end, where wheel spray and stones reach the harness
- 3Retest after the repair: press the steer rocker to the right, listen for the click and watch the right wheel
- 4Look at the right axle harness for stone damage, then meter the right coil to its case
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Flow Control Valve3 codes
JLG 33314Flow Control Valve: Open circuit
The controller drives the flow control valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Winding burnt through at one end so the coil reads open
- Flow control coil open, so boom speed cannot be controlled and functions go slow or stick at one speed
- Harness fatigued and parted at the turntable manifold where oil soaks into the connector
- Terminal worn loose in its housing (the flow control plug sits on the turntable manifold and takes oil mist)
Checks
- 1Ohm the solenoid coil on the turntable manifold with the plug off and compare with a matching good coil
- 2Test both wires with the plug off and flex them at the turntable manifold where oil soaks into the connector to catch a hidden break
- 3Try it on the machine: select a boom function and check the speed changes smoothly with the joystick
- 4Compare boom speed on two functions: if both are slow the flow control coil circuit is open
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 33315Flow Control Valve: Short to battery
The controller reads battery voltage on the flow control valve output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Output wire touching a battery-fed wire where two harness legs cross
- Flow control wire touching a feed so the valve is held open and speed control is lost
- Harness rubbed bare and touching a feed at the turntable manifold where oil soaks into the connector
- Wet plug bridging the signal pin to supply, since the flow control plug sits on the turntable manifold and takes oil mist
Checks
- 1With the flow control valve plug off on the turntable manifold and the key on, measure the output wire to ground; any voltage means a short to supply
- 2Inspect the harness for bare spots, burnt insulation and melted clamps, especially at the turntable manifold where oil soaks into the connector
- 3Select a boom function and check the speed changes smoothly with the joystick; battery voltage should appear on the output only when it is commanded on
- 4Check the flow control wire for voltage with the plug off and key on
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JLG 33316Flow Control Valve: Short to ground
The controller sees the flow control valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Winding broken down to earth
- Flow control coil shorted by oil mist in the turntable manifold plug
- Earth path from a worn lead at the turntable manifold where oil soaks into the connector
- Green corrosion in the connector (the flow control plug sits on the turntable manifold and takes oil mist)
Checks
- 1Separate the connector on the turntable manifold and see whether the code goes with the load
- 2Look for rub marks on the harness at the turntable manifold where oil soaks into the connector and test any suspect length to earth
- 3Retest after the repair: select a boom function and check the speed changes smoothly with the joystick
- 4Dry the manifold plug and meter the coil to its case
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Drive Forward Valve3 codes
JLG 33317Drive Forward Valve: Open circuit
The controller drives the drive forward valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Coil gone open from heat or age
- Drive forward coil open, so the pump gives no forward flow and the machine only goes backwards
- Conductor snapped in the harness along the chassis near the drive pump, where engine vibration shakes the harness
- Contact fretting in the plug, which is likely because the drive forward plug is down at the drive pump, shaken by engine vibration
Checks
- 1Meter the solenoid coil on the drive pump or drive valve for an open reading
- 2Test between the module pin and the plug section by section, beginning along the chassis near the drive pump, where engine vibration shakes the harness
- 3Try it on the machine: push the drive stick forward and listen for the coil click at the pump, then see if the wheels turn
- 4Push the stick back: if reverse works the pump and brake are fine and only the forward coil is open
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 33318Drive Forward Valve: Short to battery
The controller reads battery voltage on the drive forward valve output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Lead rubbed through against a live cable
- Drive forward wire touching a feed at the drive pump so the machine may creep forward
- Chafed insulation along the chassis near the drive pump, where engine vibration shakes the harness letting a feed touch the output wire
- Crushed pin touching a live neighbour; the drive forward plug is down at the drive pump, shaken by engine vibration
Checks
- 1Pull the plug on the drive pump or drive valve, key on, and check the output wire for voltage; if it stays with the load off, suspect the module
- 2Feel along the harness along the chassis near the drive pump, where engine vibration shakes the harness for scuffed, hard or discoloured insulation
- 3Push the drive stick forward and listen for the coil click at the pump, then see if the wheels turn; battery voltage should appear on the output only when it is commanded on
- 4Chock the wheels and watch whether the machine tries to move forward with the stick centred
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JLG 33319Drive Forward Valve: Short to ground
The controller sees the drive forward valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Winding broken down to earth
- Drive forward coil shorted by engine vibration chafing the lead at the pump
- Wire chafed through to the frame along the chassis near the drive pump, where engine vibration shakes the harness
- Dirt and water bridging a pin to ground; the drive forward plug is down at the drive pump, shaken by engine vibration
Checks
- 1Disconnect the load on the drive pump or drive valve; the code staying means a harness or module fault
- 2Meter between the signal pin and chassis with the plug apart; a reading shows the earth path, probably along the chassis near the drive pump, where engine vibration shakes the harness
- 3Push the drive stick forward and listen for the coil click at the pump, then see if the wheels turn; the analyzer output should go to supply, not stay at zero
- 4Check the lead at the pump bracket for chafing and test the forward coil to its case
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Drive Reverse Valve2 codes
JLG 33320Drive Reverse Valve: Open circuit
The controller drives the drive reverse valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Coil gone open from heat or age
- Drive reverse coil open, so the pump gives no reverse flow and the machine only goes forward
- Lead stretched or kinked until it broke at the pump mounting bracket, where a clamp can cut the sheath
- Corroded or open terminal in the plug; the drive reverse connector sits at the drive valve and shakes with the engine
Checks
- 1Read the coil resistance at the connector on the drive pump or drive valve; no reading means a burnt winding
- 2Test both wires with the plug off and flex them at the pump mounting bracket, where a clamp can cut the sheath to catch a hidden break
- 3Try it on the machine: pull the drive stick back, listen for the click at the drive valve, and watch the wheels
- 4Push the stick forward: if forward works the pump and brake are fine and only the reverse coil is open
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 33322Drive Reverse Valve: Short to ground
The controller sees the drive reverse valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Burnt turns grounding the drive reverse valve output
- Drive reverse coil shorted where a clamp has cut the lead at the pump bracket
- Signal wire rubbed bare on metal at the pump mounting bracket, where a clamp can cut the sheath
- Wet or corroded plug, since the drive reverse connector sits at the drive valve and shakes with the engine
Checks
- 1Disconnect the load on the drive pump or drive valve; the code staying means a harness or module fault
- 2Test the output wire to the chassis with the connector open; any path is the short, most likely at the pump mounting bracket, where a clamp can cut the sheath
- 3With the analyzer open, pull the drive stick back, listen for the click at the drive valve, and watch the wheels and watch the output state
- 4Look at the pump bracket clamp for a cut sheath and test the reverse coil to its case
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Drive2 codes
JLG 33331Drive: Current feedback reading too low
The measured coil current on the drive circuit is lower than commanded, so the controller cannot trust that output. The drive function may be slow, weak or locked out until it is corrected.· Real conditionReal conditionCheck soonCauses
- Coil resistance drifted high from years of heat cycling
- Voltage drop through a poor connector, since the drive coil plugs are on the pump end, shaken by engine vibration
- Low supply voltage under load from a tired battery or loose ground
- A drive coil weakened by vibration at the pump, so the pump swashplate gets less control current than asked and the machine is sluggish
Checks
- 1Ohm the coil on the drive pump or valve and compare with a good one
- 2Inspect the plug for pushed-back pins and heat marks, then measure the coil supply under command
- 3Measure the module supply with the engine loaded to see whether it sags
- 4With the analyzer open, move the drive joystick slowly and watch the drive current in the analyzer
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JLG 33410Drive: Current feedback reading lost
The measured coil current on the drive circuit is not being read at all, so the controller cannot trust that output. The drive function may be locked out until the feedback returns.· OtherOtherCheck soonCauses
- Coil open and passing no current
- Open sense wire between the coil circuit and the ground module
- Feedback sense stage failed inside the ground module
- Drive coil feedback wire open between the pump and the module, so the module sees no drive current at all and locks drive out
Checks
- 1Ohm the coil on the drive pump or valve; a good one reads a low but steady resistance
- 2Test the feedback lead from its pin on the module to the coil end for continuity
- 3Check the module and coil connectors for pushed-back or corroded pins
- 4Check in the analyzer whether any current reading appears when you move the drive joystick slowly and watch the drive current in the analyzer
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Flow control valve2 codes
JLG 33415Flow control valve: Current feedback reading too low
The measured coil current on the flow control valve circuit is lower than commanded, so the controller cannot trust that output.· Real conditionReal conditionCheck soonCauses
- Coil turns partly burnt, so the current falls short
- Voltage drop through a poor connector, since the flow control plug is on the turntable manifold, wet with oil mist
- Low supply voltage under load from a tired battery or loose ground
- Flow control coil resistance high, so boom functions slow down and cannot reach full speed
Checks
- 1Measure the resistance of the flow control valve coil on the turntable manifold with the plug off and compare with the matching coil
- 2Back-probe the coil plug while the function runs; a low reading with a good battery means voltage lost in the wiring
- 3Load test the battery and check the module ground for a voltage drop
- 4With the analyzer open, select a boom function and watch the flow control current in the analyzer
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JLG 33419Flow control valve: Current feedback reading lost
The measured coil current on the flow control valve circuit is not being read at all, so the controller cannot trust that output.· OtherOtherCheck soonCauses
- Coil open and passing no current
- Feedback lead cut by a clamp or chafed through
- Module input for this current channel damaged
- Flow control feedback lead open at the turntable manifold plug, so the module cannot see the speed control current
Checks
- 1Unplug the flow control valve coil on the turntable manifold and measure the coil resistance; an open reading means it is dead
- 2Check the current feedback wire between the coil circuit and the ground module for continuity
- 3Reseat the module connector and the coil plug and look for backed-out pins
- 4Check in the analyzer whether any current reading appears when you select a boom function and watch the flow control current in the analyzer
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Read the code to see which valve and which failure is named
- 2Command the function from the analyzer and listen for the coil click
- 3Unplug the valve and see whether the code changes
- 4Ohm the coil and inspect the harness and plug
- 5Test drive or steer slowly after the repair
Causes
- Coil failed or shorted
- Harness crushed or chafed near the axle or chassis
- Plug loose or corroded at the valve
- Output driver in the module damaged
Most common here: shorted low (5 of 18)
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
When to stop
You'll notice: The machine will not drive in one direction, will not steer one way, or drives at the wrong speed, and the code names the valve.
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
