JLG · Outputs (valves and coils)
JLG Main lift, swing and tower lift valves and current fault codes
These are the proportional solenoid coils that move the main boom and turret: lift up/down on the main control valve bank, swing left/right on the turret valve, and on tower boom machines tower lift up/down on the tower section. The ground module drives each coil and measures its current, so a short to battery, short to ground, open circuit or a current reading that is too low or lost is reported against the named coil or circuit.
More about these partsLess
Each coil has its own plug on the valve bank, so the part named in the message tells you which plug to open.
Where this code shows
Turn the key on and watch the fault lamp or platform display.
What do these codes mean?
JLG codes 334 to 33425 are all about the main lift, swing and tower lift valves and current. The most common failure type is open circuit (6 of 21); none needs an immediate stop. Start with this check: name the coil from the message, then command that direction from the analyzer and listen for the click on the valve bank.
How urgent are they?
None of the 21 codes here means stop now; all 21 can wait until the shift ends, but find the cause before the next one.
- Check soon21
What should I check first?
Name the coil from the message, then command that direction from the analyzer and listen for the click on the valve bank
Shared checks21 of 21
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Lift Up Valve2 codes
JLG 334Lift Up Valve: Open circuit
The controller drives the lift up valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Winding burnt through at one end so the coil reads open
- Lift up solenoid open, so the main cylinder never gets oil when lift up is selected
- Wire work-hardened and snapped inside its sheath where the harness bends through the turntable and passes the boom pivot
- Pin backed out or loose in the connector, because the lift up plug sits on the valve bank under the turntable covers, where hydraulic oil mist and wash water get in
Checks
- 1Unplug the lift up valve on the main control valve bank at the turntable and measure across its two pins; an open reading means a dead solenoid coil
- 2Test between the module pin and the plug section by section, beginning where the harness bends through the turntable and passes the boom pivot
- 3Try it on the machine: select lift up from the ground station and listen for the click at the lift valve bank, then see whether the boom rises
- 4Select lift down and swing as a control test: if they work, the pump and key are fine and only the lift up circuit is dead
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
JLG 33406Lift Up Valve: Short to ground
The controller sees the lift up valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Lift up valve solenoid coil shorted to its case
- Lift up coil insulation failed and now leaks to the valve body, which also pulls the lift supply down
- Earth path from a worn lead where the harness bends through the turntable and passes the boom pivot
- Green corrosion in the connector (the lift up plug sits on the valve bank under the turntable covers, where hydraulic oil mist and wash water get in)
Checks
- 1Pull the plug on the main control valve bank at the turntable and recycle EMS to see whether the code stays
- 2Look for rub marks on the harness where the harness bends through the turntable and passes the boom pivot and test any suspect length to earth
- 3Retest after the repair: select lift up from the ground station and listen for the click at the lift valve bank, then see whether the boom rises
- 4Check that the lift up cartridge is tight and not weeping oil into the coil tube, because a wet coil shorts to its case
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Lift Down Valve2 codes
JLG 335Lift Down Valve: Short to battery
The controller reads battery voltage on the lift down valve output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Output wire touching a battery-fed wire where two harness legs cross
- Lift down wire touching a supply feed in the turntable loom, so the boom can sink or hold unpredictably
- Damaged sheath near the turntable swing-ring cable path, where the lift wires share a clamp with other coils, exposing the wire to a live one
- Corrosion between pins in the plug (the lift down connector hangs lower on the bank and picks up oil seepage from the cylinder hoses)
Checks
- 1With the load off on the main control valve bank at the turntable and the key on, any reading on the output wire is the short
- 2Look for a wire crossing a live feed near the turntable swing-ring cable path, where the lift wires share a clamp with other coils, and separate or replace it
- 3With the analyzer open, select lift down at the ground controls, listen for the click, and see whether the boom starts to settle; if it is stuck up, use the emergency lowering method in the machine manual and compare the output voltage with the commanded state
- 4Keep the platform clear and the boom supported while testing; with the lift down plug off, any voltage on the wire is the short
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
JLG 336Lift Down Valve: Open circuit
The controller drives the lift down valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Broken internal lead in the solenoid coil
- Lift down solenoid open, so the boom cannot be lowered from the controls and stays up
- Lead stretched or kinked until it broke near the turntable swing-ring cable path, where the lift wires share a clamp with other coils
- Pin backed out or loose in the connector, because the lift down connector hangs lower on the bank and picks up oil seepage from the cylinder hoses
Checks
- 1Unplug the lift down valve on the main control valve bank at the turntable and measure across its two pins; an open reading means a dead solenoid coil
- 2Meter the wires end to end while someone moves the harness near the turntable swing-ring cable path, where the lift wires share a clamp with other coils
- 3Command the output from the analyzer and select lift down at the ground controls, listen for the click, and see whether the boom starts to settle; if it is stuck up, use the emergency lowering method in the machine manual
- 4If the boom is stuck high, lower it with the emergency lowering method in the machine manual before opening the valve bank
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Tower Lift Up Valve2 codes
JLG 33106Tower Lift Up Valve: Short to ground
The controller sees the tower lift up valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Coil insulation failed, leaking to the body
- Tower lift up coil shorted where the cable folds at the tower pivot
- Signal wire rubbed bare on metal at the tower pivot, where the tower cable folds with every raise
- Wet or corroded plug, since the tower lift up plug is at the tower pivot where the cable flexes with every movement
Checks
- 1Separate the connector on the boom valve bank and see whether the code goes with the load
- 2Meter between the signal pin and chassis with the plug apart; a reading shows the earth path, probably at the tower pivot, where the tower cable folds with every raise
- 3With the analyzer open, select tower lift up and listen for the solenoid click on the boom bank, then watch the tower boom rise and watch the output state
- 4Fold the tower pivot slowly while metering the up lead to the frame and watch for a reading
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JLG 33107Tower Lift Up Valve: Open circuit
The controller drives the tower lift up valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Broken internal lead in the solenoid coil
- Tower lift up coil open, so the tower boom stays down and the machine cannot reach full height
- Wire work-hardened and snapped inside its sheath at the tower pivot, where the tower cable folds with every raise
- Corroded or open terminal in the plug; the tower lift up plug is at the tower pivot where the cable flexes with every movement
Checks
- 1Read the coil resistance at the connector on the boom valve bank; no reading means a burnt winding
- 2Test both wires with the plug off and flex them at the tower pivot, where the tower cable folds with every raise to catch a hidden break
- 3Select tower lift up and listen for the solenoid click on the boom bank, then watch the tower boom rise; the analyzer should show the module sending the command
- 4Try tower lift down: if it works the circuit is alive and only the up coil is open
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Tower Lift Down Valve2 codes
JLG 33109Tower Lift Down Valve: Short to ground
The controller sees the tower lift down valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Winding broken down to earth
- Tower lift down coil shorted where the cable lies against a hose that has worn it
- Earth path from a worn lead along the tower section, where the cable lies against hoses that can chafe it
- Green corrosion in the connector (the tower lift down connector sits at the tower block, and its seal wears from flexing)
Checks
- 1Unplug the tower lift down valve on the boom valve bank; if the code clears the solenoid coil is the short, if not the wiring or module is
- 2Meter between the signal pin and chassis with the plug apart; a reading shows the earth path, probably along the tower section, where the cable lies against hoses that can chafe it
- 3Retest after the repair: select tower lift down, listen for the click and see whether the tower boom lowers
- 4Look along the tower section for a hose rubbing on the cable
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JLG 33110Tower Lift Down Valve: Open circuit
The controller drives the tower lift down valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Coil gone open from heat or age
- Tower lift down coil open, so the tower boom stays up and holds the platform at height
- Lead stretched or kinked until it broke along the tower section, where the cable lies against hoses that can chafe it
- Corroded or open terminal in the plug; the tower lift down connector sits at the tower block, and its seal wears from flexing
Checks
- 1Read the coil resistance at the connector on the boom valve bank; no reading means a burnt winding
- 2Test between the module pin and the plug section by section, beginning along the tower section, where the cable lies against hoses that can chafe it
- 3Try it on the machine: select tower lift down, listen for the click and see whether the tower boom lowers
- 4If the tower boom is stuck high, lower it with the emergency method in the machine manual before opening the valve bank
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Swing Right Valve2 codes
JLG 33118Swing Right Valve: Short to ground
The controller sees the swing right valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Burnt turns grounding the swing right valve output
- Swing right coil shorted by oil and water on the turntable bank plug
- Wire chafed through to the frame where the cable crosses the swing bearing between turntable and chassis
- Dirt and water bridging a pin to ground; the swing right plug is on the turntable bank, soaked by oil mist and washdown
Checks
- 1Unplug the swing right valve on the turntable valve bank; if the code clears the solenoid coil is the short, if not the wiring or module is
- 2Test the output wire to the chassis with the connector open; any path is the short, most likely where the cable crosses the swing bearing between turntable and chassis
- 3Swing right from the platform joystick, listen for the click on the turntable bank, and watch the turntable turn; the analyzer output should go to supply, not stay at zero
- 4Clean and dry the turntable bank plug before testing, as oil can short a good coil
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JLG 33119Swing Right Valve: Open circuit
The controller drives the swing right valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Winding burnt through at one end so the coil reads open
- Swing right coil open, so the turntable will not turn right but may swing left
- Wire work-hardened and snapped inside its sheath where the cable crosses the swing bearing between turntable and chassis
- Pin backed out or loose in the connector, because the swing right plug is on the turntable bank, soaked by oil mist and washdown
Checks
- 1Unplug the swing right valve on the turntable valve bank and measure across its two pins; an open reading means a dead solenoid coil
- 2Meter the wires end to end while someone moves the harness where the cable crosses the swing bearing between turntable and chassis
- 3Command the output from the analyzer and swing right from the platform joystick, listen for the click on the turntable bank, and watch the turntable turn
- 4Try swing left: if it works the swing motor and pump are fine and only the right coil is open
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Swing Left Valve2 codes
JLG 33122Swing Left Valve: Short to ground
The controller sees the swing left valve output pulled low while it is commanded on, so the circuit is shorted to ground. EMS must be recycled to clear it.· Shorted lowShorted lowCheck soonCauses
- Burnt turns grounding the swing left valve output
- Swing left coil shorted where the turntable cable loop rubs
- Signal wire rubbed bare on metal at the turntable cable loop that winds and unwinds as the boom swings
- Wet or corroded plug, since the swing left connector sits on the turntable block and collects oil and grime
Checks
- 1Pull the plug on the turntable valve bank and recycle EMS to see whether the code stays
- 2With the plug off, check the signal wire to the frame (it should be open), starting at the turntable cable loop that winds and unwinds as the boom swings
- 3With the analyzer open, swing left, listen for the click at the swing valve, and see if the turntable moves and watch the output state
- 4Swing slowly and watch the cable loop at the turntable for rubbing or pinching
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
JLG 33295Swing Left Valve: Open circuit
The controller drives the swing left valve output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it.· Open circuitOpen circuitCheck soonCauses
- Open winding in the coil
- Swing left coil open, so the turntable will not turn left but may swing right
- Conductor snapped in the harness at the turntable cable loop that winds and unwinds as the boom swings
- Pin backed out or loose in the connector, because the swing left connector sits on the turntable block and collects oil and grime
Checks
- 1Unplug the swing left valve on the turntable valve bank and measure across its two pins; an open reading means a dead solenoid coil
- 2Meter the wires end to end while someone moves the harness at the turntable cable loop that winds and unwinds as the boom swings
- 3Command the output from the analyzer and swing left, listen for the click at the swing valve, and see if the turntable moves
- 4Try swing right to prove the motor and pump work, then chase the left coil circuit
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Lift Valves1 code
JLG 33182Lift Valves: Short to battery
The controller reads battery voltage on the lift valves output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Output wire touching a battery-fed wire where two harness legs cross
- Lift valve output touched by a supply wire in the lift harness so one of the lift coils is held on
- Melted insulation where the lift up and lift down wires run together through the turntable
- Crushed pin touching a live neighbour; both lift coil plugs sit side by side on the bank under the turntable covers
Checks
- 1Pull the plug on the main control valve bank at the turntable, key on, and check the output wire for voltage; if it stays with the load off, suspect the module
- 2Trace the wire alongside any supply wire and look for a touch point where the lift up and lift down wires run together through the turntable
- 3Watch the analyzer output as you unplug lift up and lift down one at a time to see which coil carries the fault
- 4Plug the lift up and down coils back one at a time with the key on and watch which one makes the code return
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Lift2 codes
JLG 33287Lift: Current feedback reading too low
The measured coil current on the lift circuit is lower than commanded, so the controller cannot trust that output. The lift function may be slow, weak or locked out until it is corrected.· Real conditionReal conditionCheck soonCauses
- Resistance high in the lift valve coils from heat damage or an old winding
- Voltage drop through a poor connector, since the lift coil plugs sit on the bank under the turntable covers
- Low supply voltage under load from a tired battery or loose ground
- A lift coil with high resistance, so the lift valve opens only part way and the boom rises slowly
Checks
- 1Ohm the coil on the main valve bank at the turntable and compare with a good one
- 2Check the plug for loose or green pins and measure the voltage at the coil while the function is commanded
- 3Check battery voltage and the main ground; low supply will show up as low coil current
- 4With the analyzer open, move the lift joystick slowly and watch the lift current in the analyzer
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JLG 33417Lift: Current feedback reading lost
The measured coil current on the lift circuit is not being read at all, so the controller cannot trust that output. The lift function may be locked out until the feedback returns.· OtherOtherCheck soonCauses
- Coil open and passing no current
- Feedback pin backed out of the module connector
- Ground module reading zero on this channel after a surge
- Lift current feedback lead open between the valve bank and the module, so lift is locked out until a reading returns
Checks
- 1Take the plug off on the main valve bank at the turntable and read the coil across its pins
- 2Check the current feedback wire between the coil circuit and the ground module for continuity
- 3Reseat the module connector and the coil plug and look for backed-out pins
- 4Check in the analyzer whether any current reading appears when you move the lift joystick slowly and watch the lift current in the analyzer
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Swing Valves1 code
JLG 33412Swing Valves: Short to battery
The controller reads battery voltage on the swing valves output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Two harness legs bundled so tightly that a worn spot joins them
- Swing valve output touched by a supply wire so one swing coil is held on and the turntable may turn on its own
- Melted insulation where the swing left and swing right wires share a harness leg
- Corrosion between pins in the plug (both swing coil plugs share a harness leg on the turntable bank)
Checks
- 1With the load off on the turntable valve bank and the key on, any reading on the output wire is the short
- 2Trace the wire alongside any supply wire and look for a touch point where the swing left and swing right wires share a harness leg
- 3With the analyzer open, unplug swing left and swing right one at a time to see which carries the fault and compare the output voltage with the commanded state
- 4Keep clear of the boom and plug the swing coils back one at a time to see which makes the code return
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Tower lift2 codes
JLG 33413Tower lift: Current feedback reading too low
The measured coil current on the tower lift circuit is lower than commanded, so the controller cannot trust that output. The tower lift function may be slow, weak or locked out until it is corrected.· Real conditionReal conditionCheck soonCauses
- Resistance high in the tower lift valve coils from heat damage or an old winding
- High-resistance joint in the plug (the tower lift plugs sit on the boom bank near the tower pivot)
- Voltage sag on the module supply when the engine is cranking or loaded
- Tower lift coil resistance high from heat at the tower pivot block, so the tower boom is slow
Checks
- 1Ohm the coil on the boom valve bank and compare with a good one
- 2Back-probe the coil plug while the function runs; a low reading with a good battery means voltage lost in the wiring
- 3Load test the battery and check the module ground for a voltage drop
- 4With the analyzer open, move the tower lift control slowly and watch the tower lift current in the analyzer
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JLG 33416Tower lift: Current feedback reading lost
The measured coil current on the tower lift circuit is not being read at all, so the controller cannot trust that output. The tower lift function may be locked out until the feedback returns.· OtherOtherCheck soonCauses
- Dead winding, so there is nothing to measure
- Feedback lead cut by a clamp or chafed through
- Module input for this current channel damaged
- Tower lift feedback lead broken where the cable folds at the tower pivot, so the module reads no current
Checks
- 1Ohm the coil on the boom valve bank; a good one reads a low but steady resistance
- 2Test the sense lead for a break by flexing it while metering
- 3Inspect the module plug for a feedback pin that has worked loose
- 4Check in the analyzer whether any current reading appears when you move the tower lift control slowly and watch the tower lift current in the analyzer
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Swing2 codes
JLG 33414Swing: Current feedback reading too low
The measured coil current on the swing circuit is lower than commanded, so the controller cannot trust that output. The swing function may be slow, weak or locked out until it is corrected.· Real conditionReal conditionCheck soonCauses
- Aged winding passing less current than commanded
- Loose pin adding resistance, because the swing coil plugs sit on the turntable bank, soaked by oil mist
- Poor module ground adding drop to the return side
- Swing coil resistance high, so the swing valve opens only part way and the turntable is slow or jerks when stopping
Checks
- 1Measure the resistance of the swing valve coils on the turntable valve bank with the plug off and compare with the matching coil
- 2Inspect the plug for pushed-back pins and heat marks, then measure the coil supply under command
- 3Measure the module supply with the engine loaded to see whether it sags
- 4With the analyzer open, move the swing joystick slowly and watch the swing current in the analyzer
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
JLG 33418Swing: Current feedback reading lost
The measured coil current on the swing circuit is not being read at all, so the controller cannot trust that output. The swing function may be locked out until the feedback returns.· OtherOtherCheck soonCauses
- Open swing valve coils circuit, so no current can flow to measure
- Open sense wire between the coil circuit and the ground module
- Feedback sense stage failed inside the ground module
- Swing feedback lead broken in the turntable cable loop, so the module reads no swing current and holds swing off
Checks
- 1Take the plug off on the turntable valve bank and read the coil across its pins
- 2Test the sense lead for a break by flexing it while metering
- 3Inspect the module plug for a feedback pin that has worked loose
- 4Check in the analyzer whether any current reading appears when you move the swing joystick slowly and watch the swing current in the analyzer
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Tower Lift Valves1 code
JLG 33425Tower Lift Valves: Short to battery
The controller reads battery voltage on the tower lift valves output while it is commanded off, so the circuit is shorted to battery. EMS must be recycled to clear it.· Shorted highShorted highCheck soonCauses
- Insulation worn between the signal and a supply feed
- Tower lift valve output touched by a supply wire so a tower coil is held on
- Melted insulation where the tower lift up and down wires share a harness leg
- Wet plug bridging the signal pin to supply, since both tower lift plugs sit on the boom bank near the pivot
Checks
- 1With the tower lift valves plug off on the boom valve bank and the key on, measure the output wire to ground; any voltage means a short to supply
- 2Look for a wire crossing a live feed where the tower lift up and down wires share a harness leg, and separate or replace it
- 3With the analyzer open, unplug tower lift up and down one at a time to see which carries the fault and compare the output voltage with the commanded state
- 4Plug the tower lift up and down coils back one at a time with the key on and note which returns the code
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Shared checks
Checks, in order
- 1Name the coil from the message, then command that direction from the analyzer and listen for the click on the valve bank
- 2Unplug the named coil: if the code changes to an open circuit the coil is the cause, if it stays the harness or module is
- 3Ohm the coil and compare it with its partner on the same function
- 4Look at the harness through the turntable and boom base for rub marks, and at the plugs for green pins
- 5Move the stick slowly with the analyzer open and watch the current for that coil rise smoothly
Causes
- A coil with burnt turns, a case short or high resistance after heat or water
- Harness chafed where it bends through the turntable or passes the boom pivot
- A loose or corroded coil plug on the valve bank, giving voltage drop or an open
- A supply wire touching a coil output where two harness legs run together
Most common here: open circuit (6 of 21)
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
When to stop
You'll notice: The named movement is lost or weak: the boom will not lift or lower, the turret will not swing, or the tower section will not move.
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
