JLG · Outputs (valves and coils)
JLG Fault Code 332
Brake - open circuit
What does JLG code 332 mean?
The controller drives the brake output but feedback shows an open circuit (feedback reads high while the output is off). That function will not work; EMS must be recycled to clear it. Urgency: stop now - shut down and fix before working on. Check first: ohm the solenoid coil on the drive manifold at the chassis with the plug off and compare with a matching good coil.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Ohm the solenoid coil on the drive manifold at the chassis with the plug off and compare with a matching good coil
Then 4 more checksWhere this code shows
Turn the key on and watch the fault lamp or platform display.
Checks
0 of 5 done
Causes
- Broken internal lead in the solenoid coil
- Brake release coil open, so the brakes never get the pressure to lift and the machine stays held
- Conductor snapped in the harness along the chassis frame rails near the drive motors, where heat and road debris wear the sheathing
- Terminal worn loose in its housing (the brake valve plug sits low on the drive manifold and collects wash water and road spray)
1 more causeFewer causes
- Return wire off its ring terminal
How it failed
You'll notice: The wheels do not turn when the drive joystick is moved, even though the engine runs and the pump makes flow.
Open circuitRead from how the source describes the code
No current flows, or the signal floats - a wire, pin or coil is broken.
- Meter test
- Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
- Good result
- Near 0 Ω on each wire. The part reads its listed resistance, not OL.
When to stop
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Drive brake, traction lock, oscillating axle and dump valves
3 other codes on this part are also open circuit (3359, 3366, 33421). When they show together, start at the wiring and connector they share.
- 3-5Brake pressure problemOtherCheck soon
- 331Brake - short to batteryShorted highStop now
- 332Brake - open circuitOpen circuitStop now
- 3358Main Dump Valve - short to groundShorted lowStop now
- 3359Main Dump Valve - open circuitOpen circuitStop now
- 3360Main Dump Valve - short to batteryShorted highStop now
- 3361Brake - short to groundShorted lowStop now
- 3365Steer Dump Valve - short to groundShorted lowStop now
- 3366Steer Dump Valve - open circuitOpen circuitStop now
Show the other 7 codesHide the other codes
- 3367Steer Dump Valve - short to batteryShorted highStop now
- 8669Oscillating axle switch disagreementOtherCheck soon
- 33420Traction Lock Valve - short to batteryShorted highCheck soon
- 33421Traction Lock Valve - open circuitOpen circuitCheck soon
- 33422Traction Lock Valve - short to groundShorted lowCheck soon
- 33423Oscillating Axle Valves - short to batteryShorted highCheck soon
- 33424Oscillating Axle Valves - short to groundShorted lowCheck soon
Other JLG codes: Outputs (valves and coils)
- 3-3Driver (output) short or open circuit
- 334Lift Up Valve - open circuit
- 335Lift Down Valve - short to battery
- 336Lift Down Valve - open circuit
- 342Platform Level Up Valve - short to battery
- 343Platform Level Up Valve - short to ground
- 345Platform Level Down Valve - open circuit
- 346Platform Level Down Valve - short to battery
Related on Equipments Finder
Source
JLG 600S/660SJ Service and Maintenance Manual 3121298, section 6 (Table 6-8 Fault Code List)
This source lists 332 and its meaning. The guidance on this page is general, not taken from it.
The source covers: JLG 600S, 600SJ, 660SJ with newer module software; same DTC scheme on other JLG Control System booms, confirm in your manual.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
