Cat · Event codes
Cat Event codes (E-codes) fault codes
Event codes are operating warnings rather than circuit faults: high exhaust, torque converter or hydraulic oil temperature, low fuel, steering malfunction, a user defined shutdown, driving with the parking brake on and a clock that needs alignment. Each says what the machine saw, not which part failed.
Where this code shows
Turn the key on and check the cluster or monitor for a warning lamp.
What do these codes mean?
Cat codes E119 to E861 are all about the event codes (E-codes). 2 need an immediate stop. Start with this check: read the event description and the logged operating conditions in Cat ET.
How urgent are they?
2 of 8 codes here mean stop now; 3 can wait until the shift ends, but find the cause before the next one; 3 are information only.
- Stop now2
- Check soon3
- Info3
What should I check first?
Read the event description and the logged operating conditions in Cat ET.
Shared checks8 of 8
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Cat E119Low fuel
The transmission ECM watches the fuel level and logs this when the tank is low. The manual says the engine may stall or crank without starting.· OtherOtherInfoCauses
- Fuel level actually low
- Fuel gauge or cluster fault
- Fuel level sensor or harness fault
Checks
- 1Turn the ignition and battery disconnect on and read the fuel gauge.
- 2If the gauge shows more than a quarter tank, replace the instrument cluster.
- 3Add about 57 liters of diesel at a time and watch the gauge move.
- 4Turn the ignition and battery disconnect on again and recheck the gauge reading.
- 5Bleed the fuel system if the engine does not restart.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat E155High torque converter oil temperature
The transmission ECM monitors the torque converter temperature sensor. A warning appears and the transmission may be limited to a lower gear.· OtherOtherCheck soonCauses
- Overloaded driveline
- Low transmission oil
- Faulty temperature sensor
Checks
- 1Reduce machine load and let the transmission cool.
- 2Connect Cat ET, select transmission 924H and check for active codes.
- 3Repair any active diagnostic codes in the list before chasing the event.
- 4Check for E155 again on Cat ET once the transmission has cooled and been worked.
- 5Continue with the manual's later steps if it remains active.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat E192Steering system malfunction
The transmission ECM detected a steering system malfunction. It resets when the ignition is turned off.· OtherOtherStop nowCauses
- Primary steering oil pressure low
- Steering switch or sensor fault
- Pump or valve fault
Checks
- 1Connect Cat ET and check for active codes first.
- 2Run the engine under normal load and recheck whether the event returns.
- 3Test secondary steering with the area clear of people and obstacles.
- 4Check the primary steering oil pressure switch and its connector for faults.
- 5Repair the cause found, clear the logged event and run the machine to confirm.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat E194High exhaust temperature
The ECM estimates exhaust temperature from ambient air, intake manifold temperature and pressure, barometric pressure and engine speed. When it calculates too high it derates engine power.· Real conditionReal conditionCheck soonCauses
- Heavy long-duration load
- Restricted air intake
- Boost or intake temperature sensor fault
Checks
- 1Check for E194 on Cat ET while the engine runs under the load that set it.
- 2Reduce the work load and see whether the code clears.
- 3Check the air filter and intake ducting for restriction that raises exhaust heat.
- 4Check coolant temperature and the cooling system.
- 5Repair any sensor codes such as 172 or 1785 first.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Cat E265User defined shutdown
The engine ECM detected the engine shutdown switch is activated. The engine stalls or cranks without starting.· OtherOtherStop nowCauses
- Shutdown switch activated
- Faulty shutdown switch
- Signal circuit shorted to ground
Checks
- 1Check that the shutdown switch is not pressed or stuck.
- 2Inspect the shutdown switch connectors for corrosion and pushed-back pins.
- 3Test the shutdown switch with a meter to see whether it is stuck closed.
- 4Run open and short tests at each harness connection.
- 5Repair the harness fault found, then clear the event and test-start the engine.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat E600High hydraulic oil temperature
The ECM detects hydraulic oil too hot. The temperature gauge reads red and the manual suggests reducing the work load.· OtherOtherCheck soonCauses
- Heavy hydraulic load
- Restricted oil cooler
- Fan fault
- Sensor fault
Checks
- 1Check whether E361 is active and diagnose high coolant temperature first if it is.
- 2Repair any other active diagnostic codes before working on the event.
- 3Reduce hydraulic load and watch whether the gauge drops back to green.
- 4If it stays red, continue with the manual's later steps.
- 5Check the hydraulic oil cooler for blockage and the fan for correct operation.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat E627Machine driven with parking brake on
The transmission ECM detects the parking brake engaged while the machine travels above 1.8 mph for at least 3 seconds. Brake damage is possible.· OtherOtherInfoCauses
- Operator drove with the brake applied
- Parking brake switch fault
- Brake release circuit fault
Checks
- 1Stop the machine and release the parking brake.
- 2Connect Cat ET to the transmission ECM and verify E627 is inactive.
- 3If it stays active, repeat troubleshooting from the start.
- 4Check the parking brake switch and its code (70).
- 5Inspect the parking brake for heat damage after the code has set.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat E861Clock manual alignment required
The engine ECM's internal clock is too far from other modules. Flashing an ECM does not load clocks, so the transmission ECM sets this.· OtherOtherInfoCauses
- Engine ECM replaced or flashed
- Module clocks not synchronised
- Transmission ECM replaced
Checks
- 1Connect Cat ET to the transmission ECM and check for active codes.
- 2Repair any active diagnostic codes in the list before chasing the event.
- 3Check the engine hours on the display against the service record.
- 4Confirm whether the transmission ECM was replaced.
- 5Align the module clocks per the manual and recheck.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Read the event description and the logged operating conditions in Cat ET.
- 2For temperature events check the cooler fins, fan drive and oil levels before any sensor.
- 3For the steering event check steering oil level and hoses and look for other active codes.
- 4For driving with the parking brake on, release the brake and confirm the switch state follows the lever.
Causes
- Real overheating from a blocked cooler or low oil level
- Operating habit such as driving with the parking brake set
- Low fuel level in the tank
- Clock or setting needing a reset
When to stop
You'll notice: A warning on the display, and for the steering and shutdown events a derate or an engine stop.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E194)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E119)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E155)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E192)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E265)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E600)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E627)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E861)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
