Cat · Fuel system
Cat Fuel rail pressure and injectors fault codes
This page covers the high-pressure fuel side: the fuel rail pressure sensor and pressure control, the per-cylinder injectors, and the wastegate solenoid that shares the ECM driver outputs. The common rail needs a controlled pressure from the high pressure pump.
More about these partsLess
Each cylinder has a solenoid injector controlled by the engine ECM.
Where this code shows
Turn the key on and check the cluster or monitor for a warning lamp.
What do these codes mean?
Cat codes CID 1 FMI 02 to CID 1797 FMI 04 are all about the fuel rail pressure and injectors. The most common failure type is open circuit (7 of 19); 5 need an immediate stop. Start with this check: check the fuel level and replace the fuel filters if needed.
How urgent are they?
5 of 19 codes here mean stop now; the other 14 can wait until the shift ends, but find the cause before the next one.
- Stop now5
- Check soon14
What should I check first?
Check the fuel level and replace the fuel filters if needed.
Shared checks19 of 19
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Cat CID 1 FMI 02Fuel injector 1 data incorrect
The ECM found cylinder 1 injector data out of limits. The manual lists a wrong trim file, wrong flash file, the injector itself, or the ECM.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Incorrect injector trim file in the ECM
- Incorrect ECM flash file
- Fuel injector 1 fault
- Engine ECM
Checks
- 1If only 1-2 is active, verify the trim file matches the injector fitted.
- 2Inspect harness connectors at the injector for a clean, secure fit.
- 3Test the circuit for opens and shorts at each harness connection.
- 4Replace the injector, then the ECM if the code persists.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Cat CID 1 FMI 05Fuel injector 1 current low
The engine ECM sees abnormally low current in the injector 1 circuit, which means the solenoid is open or the path to it has high resistance.· Open circuitOpen circuitCheck soonCauses
- High resistance or open in the engine control harness
- High resistance or open in the injector jumper harness
- Open solenoid in injector 1
- Engine ECM (rare)
Checks
- 1Disconnect the injector and measure its solenoid resistance with a multimeter; an open reading condemns the injector.
- 2Test the harness from the ECM connector to the injector for continuity.
- 3Wiggle the harness while watching the code in Cat ET to find an intermittent open.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Cat CID 1 FMI 06Fuel injector 1 current high
The engine ECM sees abnormally high current in the injector 1 circuit, pointing to a short in the harness, the jumper harness or the injector coil.· Shorted lowShorted lowCheck soonCauses
- Short in the engine control harness
- Shorted injector jumper harness
- Shorted injector 1 solenoid
- Engine ECM (rare)
Checks
- 1Disconnect the injector and see whether the code changes from active to a wiring-open condition.
- 2Check the harness for pin-to-pin and pin-to-ground shorts with a multimeter.
- 3Inspect the valve-cover connector for coolant, oil or burnt pins.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Cat CID 1 FMI 07Fuel injector 1 mechanical system not responding
The engine ECM sees that injector 1 is no longer delivering the right amount of fuel. The manual first checks that the correct trim file is installed, then points at the injector.· Part or controllerPart or controllerCheck soonCauses
- Injector 1 no longer able to deliver the correct fuel amount
- Wrong trim file installed for injector 1
- Worn or sticking injector nozzle
Checks
- 1Confirm the trim file for injector 1 is the correct one before touching hardware.
- 2Run the cylinder cut-out test in Cat ET to see whether cylinder 1 contributes.
- 3Replace injector 1 if the trim file is right and the fault stays.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Cat CID 2 FMI 02Fuel injector 2 data incorrect
Same trim or flash file mismatch as CID 1 FMI 02, raised for the cylinder 2 injector.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Trim file for injector 2 not matching the fitted injector
- Injector 2 itself
Checks
- 1Compare the trim code of injector 2 with the file loaded in the ECM.
- 2Replace injector 2 only after the files check out.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Cat CID 2 FMI 05Fuel injector 2 current low
Same open or high-resistance circuit fault as CID 1 FMI 05, on the injector 2 solenoid.· Open circuitOpen circuitCheck soonCauses
- Open solenoid or jumper wire at injector 2
- Engine harness open to injector 2
Checks
- 1Measure the injector 2 solenoid resistance; an open reading condemns it.
- 2Wiggle the injector 2 harness in Cat ET to expose an intermittent open.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Cat CID 3 FMI 02Fuel injector 3 data incorrect
Same trim or flash file mismatch as CID 1 FMI 02, raised for the cylinder 3 injector.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Trim file for injector 3 not matching the fitted injector
- Injector 3 itself
Checks
- 1Compare the trim code of injector 3 with the file loaded in the ECM.
- 2Replace injector 3 only after the files check out.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Cat CID 3 FMI 05Fuel injector 3 current low
Same open or high-resistance circuit fault as CID 1 FMI 05, on the injector 3 solenoid.· Open circuitOpen circuitCheck soonCauses
- Open solenoid or jumper wire at injector 3
- Engine harness open to injector 3
Checks
- 1Measure the injector 3 solenoid resistance; an open reading condemns it.
- 2Wiggle the injector 3 harness in Cat ET to expose an intermittent open.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Cat CID 4 FMI 05Fuel injector 4 current low
Same open or high-resistance circuit fault as CID 1 FMI 05, on the injector 4 solenoid.· Open circuitOpen circuitCheck soonCauses
- Open solenoid or jumper wire at injector 4
- Engine harness open to injector 4
Checks
- 1Measure the injector 4 solenoid resistance; an open reading condemns it.
- 2Wiggle the injector 4 harness in Cat ET to expose an intermittent open.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Cat CID 4 FMI 06Fuel injector 4 current high
Same shorted-circuit fault as CID 1 FMI 06, on the injector 4 solenoid.· Shorted lowShorted lowCheck soonCauses
- Shorted solenoid or jumper wire at injector 4
- Engine harness short near injector 4
Checks
- 1Disconnect injector 4 and see whether the code turns into an open-circuit code.
- 2Check the injector 4 valve-cover connector for oil, coolant or burnt pins.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Cat CID 6 FMI 02Fuel injector 6 data incorrect
Same trim or flash file mismatch as CID 1 FMI 02, raised for the cylinder 6 injector.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Trim file for injector 6 not matching the fitted injector
- Injector 6 itself
Checks
- 1Compare the trim code of injector 6 with the file loaded in the ECM.
- 2Replace injector 6 only after the files check out.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Cat CID 6 FMI 05Fuel injector 6 current low
Same open or high-resistance circuit fault as CID 1 FMI 05, on the injector 6 solenoid.· Open circuitOpen circuitCheck soonCauses
- Open solenoid or jumper wire at injector 6
- Engine harness open to injector 6
Checks
- 1Measure the injector 6 solenoid resistance; an open reading condemns it.
- 2Wiggle the injector 6 harness in Cat ET to expose an intermittent open.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Cat CID 6 FMI 06Fuel injector 6 current high
Same shorted-circuit fault as CID 1 FMI 06, on the injector 6 solenoid.· Shorted lowShorted lowCheck soonCauses
- Shorted solenoid or jumper wire at injector 6
- Engine harness short near injector 6
Checks
- 1Disconnect injector 6 and see whether the code turns into an open-circuit code.
- 2Check the injector 6 valve-cover connector for oil, coolant or burnt pins.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Cat E396High fuel rail pressure
The engine ECM detected excessive fuel rail pressure. The 924H manual says the engine is derated until the ignition is turned off.· OtherOtherStop nowCauses
- Fuel rail pressure sensor fault (1797-3 or 1797-4)
- Fuel pump or rail pressure control fault
- Rail pressure valve solenoid problem (1779)
Checks
- 1Connect Cat ET and check for active diagnostic codes; repair them first.
- 2If E396 is not active, move to the later test step in the manual.
- 3With no codes, turn off the ignition and battery disconnect and continue testing.
- 4Check the rail pressure sensor and its connector.
- 5Run the fuel rail pump solenoid test on Cat ET.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat E398Low fuel rail pressure
The engine ECM logged an event for fuel rail pressure that is lower than the engine needs for the requested load. The manual pairs it with the rail pressure sensor and rail valve codes.· OtherOtherStop nowCauses
- Restricted fuel supply or clogged fuel filter
- Air in the fuel or low fuel level
- Fuel rail pressure valve or high pressure pump worn
Checks
- 1Check the fuel level and replace the primary and secondary fuel filters if they are dirty.
- 2Look for active 1779 or 1797 codes in Cat ET and repair them first.
- 3Bleed the fuel system and look for air or leaks on the suction side.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat CID 526 FMI 05Wastegate solenoid current low
The ECM found low current or an open in the wastegate regulator solenoid circuit. The manual lists a high resistance or open harness, or a faulty solenoid.· Open circuitOpen circuitCheck soonCauses
- High resistance or open in the engine control harness
- Faulty wastegate solenoid
- Poor connector contact at the solenoid
Checks
- 1Connect Cat ET and run the machine under load, watching for 526-5 to set.
- 2Inspect the solenoid connector for corrosion and bent pins.
- 3Measure the solenoid coil resistance and compare it with a known good unit.
- 4Test the harness for an open between the ECM and the solenoid.
- 5Replace the solenoid or repair the harness, then clear the code.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Cat CID 1779 FMI 05Fuel rail pressure valve solenoid current low
The ECM found an open or low current in the fuel rail pump solenoid circuit. The manual lists a high resistance or open harness, or a faulty fuel pump solenoid.· Open circuitOpen circuitStop nowCauses
- High resistance or open in the engine control harness
- Faulty fuel pump solenoid
- Poor connector contact at the pump
Checks
- 1Clean and secure all connections in the solenoid circuit, then see whether the code stays active.
- 2Run open and short tests at each harness connection and replace the faulty harness.
- 3Measure the solenoid coil with the plug off to find an open winding.
- 4Replace the solenoid if the harness proves good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.
Cat CID 1797 FMI 03Fuel rail pressure sensor voltage high
The fuel rail pressure sensor signal went above 4.8 V for 0.6 seconds. The manual lists an open or shorted harness, a sensor shorted to supply voltage, or the engine ECM.· Shorted highShorted highStop nowCauses
- Engine control harness open or shorted to a power source
- Fuel rail pressure sensor shorted to supply voltage
- Engine ECM
Checks
- 1Connect Cat ET and start or try to start the engine; confirm 1797-3 is active.
- 2If 262-3 or 262-4 is active, repair the 5 V supply first.
- 3Inspect and secure the sensor connector at the rail.
- 4Run open and short tests at each harness connection and replace the faulty harness.
- 5Replace the sensor then the ECM if the signal stays high.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Cat CID 1797 FMI 04Fuel rail pressure sensor voltage low
The fuel rail pressure signal sat below 0.2 V for 0.6 seconds. The manual lists a harness shorted to ground, a shorted sensor, or the ECM.· Shorted lowShorted lowStop nowCauses
- Harness signal wire shorted to ground
- Shorted fuel rail pressure sensor
- Engine ECM
Checks
- 1Start the engine with Cat ET connected and see whether 1797-4 is active.
- 2Check for 262-3 or 262-4 before anything else.
- 3Unplug the rail pressure sensor and see whether the code changes to 1797-3.
- 4If not, test the signal wire for a short to ground back to the ECM.
- 5Replace the sensor or harness, then clear and retest.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Shared checks
Checks, in order
- 1Check the fuel level and replace the fuel filters if needed.
- 2Connect Cat ET and note which cylinder and FMI is active.
- 3Check for active 262 sensor supply codes and repair them first.
- 4Inspect the injector connectors under the valve cover for oil and burnt pins.
- 5Inspect the rail sensor and valve connectors for damage.
- 6Run the cylinder cut-out test to find a weak cylinder.
- 7Bleed the fuel system and look for air or leaks.
Causes
- Wastegate solenoid coil open or its wiring damaged
- Dirty or blocked fuel filters
- Faulty injector or solenoid
- Air or water in the fuel
Most common here: open circuit (7 of 19)
Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
When to stop
You'll notice: Hard starting, a rough-running engine, a power derate or a no-start, depending on how far rail pressure is off.
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 1 FMI 02)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 1 FMI 05)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 1 FMI 06)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 1 FMI 07)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 2 FMI 02)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 2 FMI 05)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 3 FMI 02)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 3 FMI 05)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 4 FMI 05)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 4 FMI 06)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 6 FMI 02)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 6 FMI 05)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 6 FMI 06)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E396)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E398)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 526 FMI 05)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 1779 FMI 05)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 1797 FMI 03)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 1797 FMI 04)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
