Cat · Fuel system
Cat Fault Code CID 1797 FMI 03
Fuel rail pressure sensor voltage high
What does Cat code CID 1797 FMI 03 mean?
The fuel rail pressure sensor signal went above 4.8 V for 0.6 seconds. The manual lists an open or shorted harness, a sensor shorted to supply voltage, or the engine ECM. Urgency: stop now - shut down and fix before working on. Check first: connect Cat ET and start or try to start the engine; confirm 1797-3 is active.
- CID 1797
- Which component is at fault
- FMI 03
- Voltage above normal or shorted high
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Connect Cat ET and start or try to start the engine; confirm 1797-3 is active.
Then 4 more checksWhere this code shows
Turn the key on and check the cluster or monitor for a warning lamp.
Checks
0 of 5 done
Causes
- Engine control harness open or shorted to a power source
- Fuel rail pressure sensor shorted to supply voltage
- Engine ECM
How it failed
You'll notice: The engine may run rough, derate or fail to start because the ECM cannot control rail pressure.
Shorted highRead from FMI 3: voltage above normal or shorted high
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Fuel rail pressure and injectors
- CID 6 FMI 02Fuel injector 6 data incorrectErratic or implausibleCheck soon
- CID 6 FMI 05Fuel injector 6 current lowOpen circuitCheck soon
- CID 6 FMI 06Fuel injector 6 current highShorted lowCheck soon
- E396High fuel rail pressureOtherStop now
- E398Low fuel rail pressureOtherStop now
- CID 526 FMI 05Wastegate solenoid current lowOpen circuitCheck soon
- CID 1779 FMI 05Fuel rail pressure valve solenoid current lowOpen circuitStop now
- CID 1797 FMI 03Fuel rail pressure sensor voltage highShorted highStop now
- CID 1797 FMI 04Fuel rail pressure sensor voltage lowShorted lowStop now
Show the other 10 codesHide the other codes
- CID 1 FMI 02Fuel injector 1 data incorrectErratic or implausibleCheck soon
- CID 1 FMI 05Fuel injector 1 current lowOpen circuitCheck soon
- CID 1 FMI 06Fuel injector 1 current highShorted lowCheck soon
- CID 1 FMI 07Fuel injector 1 mechanical system not respondingPart or controllerCheck soon
- CID 2 FMI 02Fuel injector 2 data incorrectErratic or implausibleCheck soon
- CID 2 FMI 05Fuel injector 2 current lowOpen circuitCheck soon
- CID 3 FMI 02Fuel injector 3 data incorrectErratic or implausibleCheck soon
- CID 3 FMI 05Fuel injector 3 current lowOpen circuitCheck soon
- CID 4 FMI 05Fuel injector 4 current lowOpen circuitCheck soon
- CID 4 FMI 06Fuel injector 4 current highShorted lowCheck soon
Related on Equipments Finder
Source
This source lists CID 1797 FMI 03 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cat 924H wheel loader with C6.6 engine (engine ECM), per the 924H field maintenance manual; the same CID-FMI scheme is used on other Cat machines with C-series ECMs.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
