Cat · Event codes
Cat Fault Code E360
Low engine oil pressure
What does Cat code E360 mean?
The engine ECM detected low oil pressure while running. On the 924H the manual says the ECM derates engine power by 17 percent per second, up to 100 percent, while it is active. Urgency: stop now - shut down and fix before working on. Check first: connect Cat ET, start the engine and check for active codes; repair any first.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Connect Cat ET, start the engine and check for active codes; repair any first.
Then 4 more checksWhere this code shows
Turn the key on and check the cluster or monitor for a warning lamp.
Checks
0 of 5 done
Causes
- Low engine oil level
- Oil pump or relief valve wear
- Wrong or diluted oil
- Failed oil pressure sensor (check 100-3 and 100-4)
How it failed
You'll notice: A warning on the panel and the engine loses power fast, up to a full derate.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Low oil pressure can wreck bearings in minutes. Stop the engine and check the level before restarting; if the level is right, do not run it again until the pressure is checked with a gauge.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine sensors and sensor supply
- CID 110 FMI 04Engine coolant temperature sensor voltage lowShorted lowCheck soon
- CID 172 FMI 03Intake manifold air temperature sensor voltage highShorted highCheck soon
- CID 172 FMI 04Intake manifold air temperature sensor voltage lowShorted lowCheck soon
- CID 262 FMI 035 V sensor supply voltage highShorted highCheck soon
- E360Low engine oil pressureOtherStop now
- E361High engine coolant temperatureOtherStop now
- E539High intake manifold temperatureReal conditionCheck soon
- E1044High intake manifold pressureOtherCheck soon
- E1045Low intake manifold pressureOtherCheck soon
Show the other 8 codesHide the other codes
- CID 41 FMI 038 V sensor supply voltage highShorted highCheck soon
- CID 91 FMI 03Throttle position sensor voltage highShorted highCheck soon
- CID 91 FMI 04Throttle position sensor voltage lowShorted lowCheck soon
- CID 100 FMI 03Engine oil pressure sensor voltage highShorted highCheck soon
- CID 100 FMI 04Engine oil pressure sensor voltage lowShorted lowCheck soon
- CID 110 FMI 03Engine coolant temperature sensor voltage highShorted highCheck soon
- CID 1785 FMI 03Intake manifold pressure sensor voltage highShorted highCheck soon
- CID 1785 FMI 04Intake manifold pressure sensor voltage lowShorted lowCheck soon
Other Cat codes: Event codes
Related on Equipments Finder
Source
TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E360)
This source lists E360 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cat 924H wheel loader with C6.6 engine (engine ECM), per the 924H field maintenance manual; the same CID-FMI scheme is used on other Cat machines with C-series ECMs.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
