Cat · Engine sensors
Cat Engine sensors and sensor supply fault codes
This page covers the engine ECM sensor inputs: throttle position, oil pressure, coolant temperature, intake manifold air temperature and pressure, and the 5 V and 8 V supplies that feed them. The throttle position sensor reports pedal or lever position to the engine ECM from an 8 V supply.
More about these partsLess
The engine ECM feeds its sensors from a regulated 5 V and an 8 V supply. The oil pressure sensor tells the engine ECM how much pressure the oil pump builds. The coolant temperature sensor drives gauge, fan control and engine protection. The intake manifold air temperature sensor measures the charge air after the turbo and cooler. The intake manifold pressure sensor reports boost to the engine ECM.
Where this code shows
Turn the key on and check the cluster or monitor for a warning lamp.
What do these codes mean?
Cat codes CID 41 FMI 03 to CID 1785 FMI 04 are all about the engine sensors and sensor supply. The most common failure type is shorted high (7 of 17); 2 need an immediate stop. Start with this check: check for active 41-3 or 41-4 first and repair the 8 V supply before the sensor.
How urgent are they?
2 of 17 codes here mean stop now; the other 15 can wait until the shift ends, but find the cause before the next one.
- Stop now2
- Check soon15
What should I check first?
Check for active 41-3 or 41-4 first and repair the 8 V supply before the sensor.
Shared checks17 of 17
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Cat CID 41 FMI 038 V sensor supply voltage high
The engine ECM's 8 V sensor supply read above 8.8 V for more than one second. That supply powers the throttle position sensor, so a short to voltage here also upsets throttle readings.· Shorted highShorted highCheck soonCauses
- Engine wiring harness shorted to voltage
- Lower cab wiring harness shorted to voltage
- Engine ECM supply output fault
Checks
- 1Connect Cat ET and start or try to start the engine; confirm 41-3 is active.
- 2Turn the ignition and battery disconnect off and open the right lower cab access panels to reach the harness.
- 3Unplug the sensors on the 8 V circuit one at a time and see whether the code clears.
- 4Test the lower cab harness for a wire touching a power feed.
- 5Replace the shorted harness, then the ECM if the supply stays high with everything unplugged.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Cat CID 91 FMI 03Throttle position sensor voltage high
The engine ECM sees the throttle position signal above its upper limit. The 924H manual lists the engine harness shorted to voltage, the lower cab harness shorted to voltage, or the ECM.· Shorted highShorted highCheck soonCauses
- Engine wiring harness signal wire shorted to a supply
- Lower cab harness shorted to voltage
- Throttle sensor supply shorted into the signal
- Engine ECM
Checks
- 1Connect Cat ET and watch for 91-3 while starting or trying to start the engine.
- 2If 41-3 or 41-4 is also active, repair the 8 V supply first because it feeds this sensor.
- 3Disconnect the sensor and read signal voltage at the harness; it should drop if the harness is clean.
- 4Inspect the lower cab harness at the pedal or lever connector for pin contact and chafing.
- 5Replace the faulty harness section, then test the ECM last.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Cat CID 91 FMI 04Throttle position sensor voltage low
The throttle position signal fell below the ECM's lower limit. The manual lists the engine harness shorted to ground, the lower cab harness shorted to ground, or the engine ECM.· Shorted lowShorted lowCheck soonCauses
- Engine wiring harness signal wire shorted to ground
- Lower cab harness chafed to the frame
- Open or shorted sensor supply (41) pulling the signal down
- Engine ECM
Checks
- 1Start or try to start the engine with Cat ET connected and confirm 91-4 is active.
- 2Check for 41-3 or 41-4 and repair the 8 V supply code first if present.
- 3Unplug the throttle sensor and check the signal wire for continuity to ground.
- 4Inspect harness sections that rub on the cab floor or frame rails for rub-through.
- 5Replace the shorted harness; replace the ECM only after the harness tests pass.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Cat CID 100 FMI 03Engine oil pressure sensor voltage high
The oil pressure sensor signal went above 4.95 V for more than eight seconds. The manual lists a harness open or shorted to another supply, the sensor shorted to supply voltage, or the ECM.· Shorted highShorted highCheck soonCauses
- Engine control harness open or shorted to a power source
- Oil pressure sensor shorted to supply voltage
- Engine ECM
Checks
- 1Connect Cat ET, check for active codes and confirm 100-3 is active.
- 2If 262-3 or 262-4 is active, repair the 5 V supply first.
- 3Check that the sensor connector E-C10 is seated with no bent pins before unplugging it.
- 4Unplug the sensor and measure the harness signal pin; open or short tests at each connection find the bad wire.
- 5Replace the sensor if the harness is clean, then the ECM last.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Cat CID 100 FMI 04Engine oil pressure sensor voltage low
The oil pressure sensor signal sat below 0.1 V for more than eight seconds. The manual lists a harness shorted to ground, a shorted sensor, or the engine ECM.· Shorted lowShorted lowCheck soonCauses
- Harness signal wire shorted to ground
- Shorted oil pressure sensor
- Engine ECM
Checks
- 1Confirm 100-4 is active with the engine running on Cat ET.
- 2Verify real oil pressure with a mechanical gauge before blaming the sensor, so you do not chase a live oil fault.
- 3Unplug the sensor; if the code changes to 100-3 the sensor was shorted.
- 4If the code stays 100-4 with the sensor unplugged, test the signal wire for a short to ground.
- 5Replace the sensor or harness, then clear and rerun.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Cat CID 110 FMI 03Engine coolant temperature sensor voltage high
The coolant temperature signal went above 4.95 V for more than eight seconds. The manual lists an engine harness open or shorted to a supply, the sensor shorted to supply voltage, or the ECM.· Shorted highShorted highCheck soonCauses
- Engine harness open or shorted to a power source
- Coolant temperature sensor shorted to supply voltage
- Engine ECM
Checks
- 1Connect Cat ET and confirm 110-3 is active with the engine running, not only logged.
- 2Check for 262-3 or 262-4 first and repair the 5 V supply before touching the temperature sensor.
- 3Unplug the sensor: a signal that stays high on the harness side means an open or short in the wiring.
- 4Inspect the sensor connector for water, green corrosion and pushed-back pins.
- 5Replace the sensor, then test the ECM only after the harness tests pass.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Cat CID 110 FMI 04Engine coolant temperature sensor voltage low
The coolant temperature signal dropped below 0.2 V for more than eight seconds. The manual lists the harness shorted to ground, a shorted sensor, or the engine ECM.· Shorted lowShorted lowCheck soonCauses
- Engine control harness shorted to ground
- Coolant temperature sensor shorted internally
- Engine ECM
Checks
- 1Confirm 110-4 is active and compare the Cat ET temperature with a thermometer reading on the coolant hose.
- 2Check for 262-3 or 262-4 first, since a faulty 5 V supply can drag the signal.
- 3Unplug the sensor; if the code flips to 110-3 the sensor itself was the short.
- 4If it stays 110-4 unplugged, test the signal wire for a short to ground along the harness.
- 5Replace the failed part and clear the logged code.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Cat CID 172 FMI 03Intake manifold air temperature sensor voltage high
The intake manifold air temperature signal read above 4.95 V for more than eight seconds. The manual lists an open or shorted harness, a sensor shorted to supply voltage, or the engine ECM.· Shorted highShorted highCheck soonCauses
- Engine control harness open or shorted to a power source
- Sensor shorted to supply voltage
- Engine ECM
Checks
- 1Open the right engine access panel and inspect the intake sensor connector.
- 2Perform open and short tests on each harness connection to isolate the bad wire.
- 3Tag the harness before replacing so the routing goes back correctly.
- 4Replace the sensor, then the ECM if the signal stays high.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Cat CID 172 FMI 04Intake manifold air temperature sensor voltage low
The intake air temperature signal fell below 0.2 V for more than eight seconds. The manual lists the harness shorted to ground, a shorted sensor, or the engine ECM.· Shorted lowShorted lowCheck soonCauses
- Engine control harness shorted to ground
- Shorted intake manifold air temperature sensor
- Engine ECM
Checks
- 1Turn the ignition and battery disconnect off and unplug connector E-C7 from the sensor.
- 2If the code changes to 172-3 with it unplugged, replace the sensor.
- 3If it stays 172-4, test the signal wire for a short to ground.
- 4Replace the harness or ECM only as the tests point.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Cat CID 262 FMI 035 V sensor supply voltage high
The ECM's 5 V supply for the pressure and temperature sensors read above 5.16 V for more than one second. The manual lists a harness shorted to another power source or the ECM.· Shorted highShorted highCheck soonCauses
- Engine control harness shorted to another power source
- Engine ECM 5 V supply fault
- A shorted sensor pulling its supply pin up
Checks
- 1Connect Cat ET and confirm 262-3 is active before looking at other sensor codes.
- 2Turn off, open the right engine access panel and unplug connector E-C10 from the oil pressure sensor.
- 3Unplug the other 5 V sensors one at a time and watch for the code to clear.
- 4Test the sensor supply wire for contact with a power feed.
- 5Replace the shorted harness; the ECM is the last item.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Cat E360Low engine oil pressure
The engine ECM detected low oil pressure while running. On the 924H the manual says the ECM derates engine power by 17 percent per second, up to 100 percent, while it is active.· OtherOtherStop nowCauses
- Low engine oil level
- Oil pump or relief valve wear
- Wrong or diluted oil
- Failed oil pressure sensor (check 100-3 and 100-4)
Checks
- 1Connect Cat ET, start the engine and check for active codes; repair any first.
- 2Stop the engine if pressure is really low, then check the oil level.
- 3Verify pressure with a mechanical gauge so you know the sensor is not lying.
- 4Check the log for 100-3 or 100-4 on the oil pressure sensor.
- 5Fix the cause, run the engine and confirm E360 is inactive.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat E361High engine coolant temperature
The engine ECM saw the coolant too hot. At the first level the lamp and alarm come on, at higher levels the ECM derates engine power by one percent per second.· OtherOtherStop nowCauses
- Low coolant level or leak
- Blocked radiator or aftercooler
- Fan, belt or tensioner fault
- Air in the cooling system
- Faulty coolant temperature sensor
Checks
- 1Check for active diagnostic codes first, such as 110-3 or 110-4.
- 2Let the engine cool, then check coolant level and condition.
- 3Inspect the aftercooler and radiator for restriction.
- 4Check the fan, fan belt and tensioner for damage.
- 5Test for air bubbles in the cooling system, which show a gasket or hose leak.
- 6Check for other active event codes before replacing parts.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat E539High intake manifold temperature
The 924H manual lists the engine ECM detecting a high temperature; it warns at level one and derates power by one percent per second at level two.· Real conditionReal conditionCheck soonCauses
- Restricted aftercooler or charge air path
- Cooling fan or belt fault
- Intake air temperature sensor fault (172-3 or 172-4)
Checks
- 1Inspect the aftercooler and charge air path for blockage.
- 2Check that the cooling fan turns freely and the fan belt is in good condition.
- 3Check coolant level and condition, topping up and flushing if it is dirty.
- 4Clear the logged event and recheck under load.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Cat E1044High intake manifold pressure
The ECM detected high intake manifold air pressure. At level two it also derates engine power by 20 percent while the condition lasts.· OtherOtherCheck soonCauses
- Wastegate solenoid not opening the wastegate
- Air filter restriction logged as E172
- High exhaust temperature logged as E194
Checks
- 1If E172 (high air filter restriction) is active, diagnose that first.
- 2If E194 (high exhaust temperature) is active, diagnose that first.
- 3With no other codes, replace the wastegate solenoid.
- 4Repair any active diagnostic codes before replacing parts.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat E1045Low intake manifold pressure
The ECM detected low intake manifold air pressure. At level two it may leave the engine short of power while the condition lasts.· OtherOtherCheck soonCauses
- Turbocharger not producing boost
- Air filter restriction logged as E172
- Exhaust restriction or heat logged as E194
Checks
- 1If E172 is active, diagnose the high air filter restriction first.
- 2If E194 is active, diagnose the high exhaust temperature first.
- 3Check for diagnostic codes; if none are active replace the turbocharger.
- 4Repair any active diagnostic codes before replacing the turbo.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Cat CID 1785 FMI 03Intake manifold pressure sensor voltage high
The boost pressure signal went above 4.95 V for more than eight seconds. The manual lists an open or shorted harness, a sensor shorted to supply voltage, or the engine ECM.· Shorted highShorted highCheck soonCauses
- Engine control harness open or shorted to a power source
- Intake manifold pressure sensor shorted to supply voltage
- Engine ECM
Checks
- 1Confirm 1785-3 is active on Cat ET with the engine running.
- 2Remove the right engine access panel and inspect the pressure sensor connector.
- 3Run open and short-circuit tests at each harness connection.
- 4Unplug the sensor and recheck the signal on the harness side.
- 5Replace the sensor, then the ECM if still high.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Cat CID 1785 FMI 04Intake manifold pressure sensor voltage low
The boost pressure signal fell below 0.1 V for more than eight seconds. The manual lists a harness shorted to ground, a shorted sensor, or the engine ECM.· Shorted lowShorted lowCheck soonCauses
- Engine control harness shorted to ground
- Intake manifold pressure sensor shorted
- Engine ECM
Checks
- 1Confirm 1785-4 is active on Cat ET with the engine running.
- 2Switch off and unplug connector E-C8 from the intake manifold pressure sensor.
- 3Restart the engine; a change to 1785-3 with the sensor unplugged points at the sensor.
- 4If it stays 1785-4, test the signal wire for a short to ground back to the ECM.
- 5Replace the faulty harness, sensor or ECM and clear the code.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Shared checks
Checks, in order
- 1Check for active 41-3 or 41-4 first and repair the 8 V supply before the sensor.
- 2Unplug the sensors on the supply one at a time and watch whether the code clears.
- 3Check the oil level and condition before anything else.
- 4Check the coolant level and look for leaks.
- 5Clean the charge air cooler and check the hoses for leaks.
- 6Look for active 262 or 526 codes and repair them first.
- 7Unplug the sensor and read the signal and supply at the harness.
Causes
- Damaged throttle sensor
- Short to voltage in a sensor or the harness
- Low oil level
- Low coolant level
Most common here: shorted high (7 of 17)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: Engine speed does not follow the pedal, sits at one speed, or drops to idle.
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 41 FMI 03)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 91 FMI 03)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 91 FMI 04)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 100 FMI 03)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 100 FMI 04)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 110 FMI 03)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 110 FMI 04)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 172 FMI 03)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 172 FMI 04)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 262 FMI 03)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E360)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E361)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E539)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E1044)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (E1045)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 1785 FMI 03)
- TM 5-3805-298-23-1 Field Maintenance Manual, 924H Wheel Loader, troubleshooting tables (CID 1785 FMI 04)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
