J1939 · Turbo
SPN 102 Fault Code
Engine intake manifold 1 pressure
What does SPN 102 mean?
Boost pressure in the intake manifold, read by the manifold pressure sensor. The ECM uses it for fuel limits, turbo control and EGR calculations. How urgent it is depends on the FMI after SPN 102 - pick it below. Check first: compare the key-on, engine-off reading with barometric pressure: the two should be close, so full scale here confirms an electrical fault.
- SPN 102
- Engine intake manifold 1 pressure
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 102 - pick it below.
What should I check first?
Compare the key-on, engine-off reading with barometric pressure: the two should be close, so full scale here confirms an electrical fault
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 102?
You'll notice: Boost reads wrong, so the ECM trims fuel and the engine feels down on power with extra smoke, and the check-engine lamp may come on.
Find the number shown after SPN 102 on your display. 3 of them have their own page with causes and checks.
- 2SPN 102 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, Mack MP8, Mack MP7, PACCAR MX-13 and 1 more
- 3SPN 102 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Mack MP8, Mack MP7, PACCAR MX-13 and 1 more
- 4SPN 102 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, PACCAR MX-13
- 5SPN 102 FMI 5: Current is below normal, or the circuit is openOpen circuitMack MP8, Mack MP7, Volvo D13
- 10SPN 102 FMI 10: The value is changing at an abnormal rateErratic or implausibleCummins ISX15
- 12SPN 102 FMI 12: Bad intelligent device or componentPart or controllerMack MP8, Mack MP7, Volvo D13
- 13SPN 102 FMI 13: The value is out of calibrationPart or controllerMack MP8, Mack MP7, Volvo D13
- 14SPN 102 FMI 14: A special-instruction condition defined by the engine maker appliesOtherMack MP8, Mack MP7, Volvo D13
- 15SPN 102 FMI 15: Value is above the normal range, least severe levelReal conditionCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 16SPN 102 FMI 16: Value is above the normal range, moderately severe levelReal conditionCummins ISX15
- 17SPN 102 FMI 17: Value is below the normal range, least severe levelReal conditionCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 18SPN 102 FMI 18: Value is below the normal range, moderately severe levelReal conditionCummins ISX15
- 31SPN 102 FMI 31: A condition exists: the ECM is flagging a defined state rather than a circuit failureReal conditionCummins ISX15
Checks
0 of 5 done
When to stop
Make the machine safe before you start: on firm level ground, attachments down, key out.
How urgent SPN 102 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Signal high or open: broken or backed-out pin, an open sensor return, or the signal shorted to the 5 V reference at the intake manifold pressure sensor
- Signal low or shorted: signal wire grounded, or the 5 V reference lost, so the intake manifold pressure sensor reads at the bottom of its range
- Real condition: boost leak at a charge air cooler hose clamp or the cooler itself, so real boost is below target
- Real condition: turbo not building boost from a stuck vane, wastegate or worn turbo
1 more causeFewer causes
- Sensor: oil or soot in the sensor port, making the reading lag and jump instead of following boost smoothly
Other Turbo codes
- SPN 105Intake manifold temperature sensor
- SPN 103Turbocharger 1 speed
- SPN 641Variable geometry turbo (VGT) actuator
- SPN 642Variable geometry turbocharger actuator 2
- SPN 1127Turbocharger boost (intake manifold) pressure
- SPN 1172Turbo compressor inlet temperature sensor
- SPN 1176Turbocharger compressor inlet pressure
- SPN 1188Turbocharger wastegate actuator
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 102 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
