J1939 · Turbo
SPN 1172 Fault Code
Engine turbocharger 1 compressor intake temperature
What does SPN 1172 mean?
Air temperature at the turbo compressor inlet, read by a sensor before the compressor. The ECM uses it for boost and EGR calculations. How urgent it is depends on the FMI after SPN 1172 - pick it below. Check first: compare the inlet reading with ambient temperature on a cold-soaked engine; they should be close.
- SPN 1172
- Engine turbocharger 1 compressor intake temperature
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 1172 - pick it below.
What should I check first?
Compare the inlet reading with ambient temperature on a cold-soaked engine; they should be close
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 1172?
You'll notice: The turbo inlet temperature is misread, so boost control and charge air corrections are a little off and the check-engine lamp comes on.
Find the number shown after SPN 1172 on your display. 2 of them have their own page with causes and checks.
- 2SPN 1172 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, Detroit DD15
- 3SPN 1172 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 1 more
- 4SPN 1172 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 1 more
- 14SPN 1172 FMI 14: Compressor inlet temperature sensor has drifted within its rangeErratic or implausibleDetroit DD13 Gen 5, Detroit DD15 Gen 5
- 21SPN 1172 FMI 21: Compressor inlet temperature sensor signal is not plausibleErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
Checks
0 of 5 done
When to stop
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
How urgent SPN 1172 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Reads cold: an open circuit or a short to supply in the compressor inlet temperature sensor wiring, which the ECM reads as an extremely low temperature
- Reads hot: signal wire shorted to ground or the compressor inlet temperature sensor element shorted, which the ECM reads as an extremely high temperature
- Real condition: air inlet pipe restricted or leaking, so the air temperature at the sensor is wrong
- Real condition: sensor reading heat soaked from the turbo
1 more causeFewer causes
- Sensor: poor connector contact at the inlet pipe, which sees vibration from the turbo
Other Turbo codes
- SPN 102Intake manifold (boost) pressure
- SPN 641Variable geometry turbo (VGT) actuator
- SPN 642Variable geometry turbocharger actuator 2
- SPN 1127Turbocharger boost (intake manifold) pressure
- SPN 1176Turbocharger compressor inlet pressure
- SPN 1188Turbocharger wastegate actuator
- SPN 1209Exhaust gas pressure
- SPN 2629Turbocharger compressor outlet temperature
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 1172 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
