Deutz · Coolant, oil and fuel sensors
Deutz Fault Code SPN 100 FMI 4
Engine - Oil pressure sensor - Voltage below normal or shorted to low source
What does Deutz code SPN 100 FMI 4 mean?
The EMR4 reads the oil pressure sensor (on the engine block or oil filter housing in the main oil gallery) signal below its valid 0.5 to 4.5 V window. Urgency: stop now - shut down and fix before working on. Check first: fit a known good oil pressure sensor temporarily, if you have one, and see whether the reading moves back into range.
- SPN 100
- Engine oil pressure
- FMI 4
- Voltage below normal or shorted low
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Fit a known good oil pressure sensor temporarily, if you have one, and see whether the reading moves back into range
Then 3 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 4 done
Causes
- 5 V reference lost: open supply wire or a short on the shared 5 V line
- Oil pressure sensor failed low
- Signal wire rubbed through to ground
How it failed
You'll notice: Expect a warning lamp; the oil pressure gauge or lamp misbehaves and the EMR4 protection function can derate or even shut the engine down if it believes pressure is truly lost.
Shorted lowRead from FMI 4: voltage below normal or shorted low
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant, oil and low-pressure fuel sensors
5 other codes on this part are also shorted low (SPN 94 FMI 4, SPN 97 FMI 4, SPN 110 FMI 4, SPN 175 FMI 4 and more). When they show together, start at the wiring and connector they share.
- SPN 97 FMI 12Engine - Water in fuel sensor - Bad intelligent device or componentPart or controllerCheck soon
- SPN 100 FMI 0Engine - Oil pressure sensor - Data above normal operational range (Most severe level)Real conditionStop now
- SPN 100 FMI 1Engine - Oil pressure sensor - Data below normal operational range (Most severe level)Real conditionStop now
- SPN 100 FMI 3Engine - Oil pressure sensor - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 100 FMI 4Engine - Oil pressure sensor - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 110 FMI 0Engine - Coolant temperature sensor - Data above normal operational range (Most severe level)Real conditionStop now
- SPN 110 FMI 1Engine - Coolant temperature sensor - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 110 FMI 3Engine - Coolant temperature sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 110 FMI 4Engine - Coolant temperature sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
Show the other 15 codesHide the other codes
- SPN 94 FMI 1Engine - Fuel low pressure sensor - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 94 FMI 3Engine - Fuel low pressure sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 94 FMI 4Engine - Fuel low pressure sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 97 FMI 3Engine - Water in fuel sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 97 FMI 4Engine - Water in fuel sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 111 FMI 1Engine - Coolant level sensor - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 175 FMI 0Engine - Oil temperature - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 175 FMI 3Engine - Oil temperature - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 175 FMI 4Engine - Oil temperature - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 523618 FMI 3Machine - Transmission oil sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 523618 FMI 4Machine - Transmission oil sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 524057 FMI 2Engine - Fuel low pressure pump - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 524132 FMI 0Engine - Fuel low pressure before pump - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 524132 FMI 1Engine - Fuel low pressure before pump - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 524132 FMI 2Engine - Fuel low pressure before pump - Data erratic intermittent or incorrectErratic or implausibleCheck soon
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 13
This source lists SPN 100 FMI 4 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
