Deutz · Coolant, oil and fuel sensors
Deutz Fault Code SPN 100 FMI 1
Engine - Oil pressure sensor - Data below normal operational range (Most severe level)
What does Deutz code SPN 100 FMI 1 mean?
The oil pressure sensor (on the engine block or oil filter housing in the main oil gallery) reports a value below the allowed range. This is a plausibility limit, so the low value may be genuine rather than a wiring fault. Urgency: stop now - shut down and fix before working on. Check first: compare with its neighbouring sensors in SerDia to see whether only this value is off.
- SPN 100
- Engine oil pressure
- FMI 1
- Data below normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Compare with its neighbouring sensors in SerDia to see whether only this value is off
Then 3 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 4 done
Causes
- Hose or port feeding the sensor split or disconnected
- Sensor body cracked or its thread leaking after an oil filter service
- Oil pressure sensor drifting low or reading with an offset
How it failed
You'll notice: Warning or derate: the oil pressure gauge or lamp misbehaves and the EMR4 protection function can derate or even shut the engine down if it believes pressure is truly lost.
Real conditionRead from FMI 1: data below normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant, oil and low-pressure fuel sensors
8 other codes on this part are also real condition (SPN 94 FMI 1, SPN 100 FMI 0, SPN 110 FMI 0, SPN 110 FMI 1 and more). When they show together, start at the wiring and connector they share.
- SPN 97 FMI 3Engine - Water in fuel sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 97 FMI 4Engine - Water in fuel sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 97 FMI 12Engine - Water in fuel sensor - Bad intelligent device or componentPart or controllerCheck soon
- SPN 100 FMI 0Engine - Oil pressure sensor - Data above normal operational range (Most severe level)Real conditionStop now
- SPN 100 FMI 1Engine - Oil pressure sensor - Data below normal operational range (Most severe level)Real conditionStop now
- SPN 100 FMI 3Engine - Oil pressure sensor - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 100 FMI 4Engine - Oil pressure sensor - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 110 FMI 0Engine - Coolant temperature sensor - Data above normal operational range (Most severe level)Real conditionStop now
- SPN 110 FMI 1Engine - Coolant temperature sensor - Data below normal operational range (Most severe level)Real conditionCheck soon
Show the other 15 codesHide the other codes
- SPN 94 FMI 1Engine - Fuel low pressure sensor - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 94 FMI 3Engine - Fuel low pressure sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 94 FMI 4Engine - Fuel low pressure sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 110 FMI 3Engine - Coolant temperature sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 110 FMI 4Engine - Coolant temperature sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 111 FMI 1Engine - Coolant level sensor - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 175 FMI 0Engine - Oil temperature - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 175 FMI 3Engine - Oil temperature - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 175 FMI 4Engine - Oil temperature - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 523618 FMI 3Machine - Transmission oil sensor - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 523618 FMI 4Machine - Transmission oil sensor - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 524057 FMI 2Engine - Fuel low pressure pump - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 524132 FMI 0Engine - Fuel low pressure before pump - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 524132 FMI 1Engine - Fuel low pressure before pump - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 524132 FMI 2Engine - Fuel low pressure before pump - Data erratic intermittent or incorrectErratic or implausibleCheck soon
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 13
This source lists SPN 100 FMI 1 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
