EF Logo

Deutz · High-pressure fuel system

Deutz Common rail: metering unit, pre-feed pump, relief valve and rail pressure fault codes

The high-pressure side of the fuel system. The fuel pre-feed pump fills the supply, the fuel metering unit (FMU, SPN 523615) meters the fuel that the high-pressure pump compresses, the rail pressure sensor (SPN 157) reports the pressure and the rail pressure relief valve (PRV, SPN 523470) opens when the rail goes too high.

More about these parts

The rail pressure control codes (SPN 164, 523613) say the pressure is not where the EMR4 wants it.

FaultStopSPN 157FMI 3Deutz · Rail pressure sensor
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.

What do these codes mean?

Deutz codes SPN 157 FMI 3 to SPN 523906 FMI 12 are all about the common rail: metering unit, pre-feed pump, relief valve and rail pressure. The most common failure type is part or controller (5 of 22); 14 need an immediate stop. Start with this check: read rail pressure actual against target in SerDia while cranking and under load.

How urgent are they?

14 of 22 codes here mean stop now; the other 8 can wait until the shift ends, but find the cause before the next one.

  • Stop now14
  • Check soon8

What should I check first?

Read rail pressure actual against target in SerDia while cranking and under load

Shared checks

22 of 22

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Rail pressure sensor2 codes

    • Deutz SPN 157 FMI 3Rail pressure sensor: Voltage high / shorted high

      The EMR4 reads the rail pressure sensor (screwed into the high-pressure common rail) signal above its valid 0.5 to 4.5 V window.· Shorted high
      Stop now

      Causes

      • Open ground return wire, which pushes the signal up to the reference
      • Signal wire touching 5 V or battery in the harness
      • Sensor on the common rail leaking or damaged after fuel system work

      Checks

      1. 1Key on: measure the 5 V reference at the rail pressure sensor plug between supply and ground; 5 V present means the supply side is fine
      2. 2With key on and engine off, the SerDia rail pressure should read close to zero; a large offset means the sensor is out of range
      3. 3Look for diesel wetness around the rail and its fittings; a leak here is a safety item as well as a fault source
      4. 4Check continuity of the sensor ground wire back to the EMR4 pin
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Engine - Rail pressure sensor - Voltage above normal or shorted to high source

      Full page for SPN 157 FMI 3
    • Deutz SPN 157 FMI 4Rail pressure sensor: Voltage low / shorted low

      The EMR4 reads the rail pressure sensor (screwed into the high-pressure common rail) signal below its valid 0.5 to 4.5 V window.· Shorted low
      Stop now

      Causes

      • Sensor on the common rail leaking or damaged after fuel system work
      • Signal wire rubbed through to ground
      • 5 V reference lost: open supply wire or a short on the shared 5 V line
      • Rail pressure sensor failed low

      Checks

      1. 1Look for diesel wetness around the rail and its fittings; a leak here is a safety item as well as a fault source
      2. 2Key on: measure the 5 V reference at the rail pressure sensor plug; no reference means open supply wire or another sensor on that line pulling it down
      3. 3Unplug other sensors sharing the 5 V line one at a time to see whether the reference comes back
      4. 4With the sensor unplugged, measure resistance from the signal pin to ground; it should not be near zero
      5. 5With key on and engine off, the SerDia rail pressure should read close to zero; a large offset means the sensor is out of range
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Engine - Rail pressure sensor - Voltage below normal or shorted to low source

  • Rail pressure1 code

    • Deutz SPN 164 FMI 2Rail pressure: Erratic reading

      The EMR4 sees the rail pressure signal erratic.· Erratic or implausible
      Check soon

      Causes

      • Air in the fuel or a starved high-pressure pump
      • Failing rail pressure sensor with a noisy signal
      • Intermittent sensor connector contact
      • Worn high-pressure pump losing pressure under load

      Checks

      1. 1Bleed the low-pressure side and check for air at the suction side of the feed pump
      2. 2Compare rail pressure actual and target in SerDia while the engine is under load, not only at idle
      3. 3Wiggle the rail sensor connector and watch the live reading for dropouts
      4. 4Replace the fuel filters and re-test, because a restricted filter shows up first under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Engine - Rail pressure - Data erratic intermittent or incorrect

      Full page for SPN 164 FMI 2
  • Fuel pressure relief valve8 codes

    • Deutz SPN 523009 FMI 9Fuel pressure relief valve: Abnormal update rate timeout

      The EMR4 sees the fuel pressure relief valve (on the common rail, opening to relieve excess pressure back to tank) update at an abnormal rate or time out.· Lost message
      Check soon

      Causes

      • Interrupted wiring or connector to the sending unit
      • Sending unit not powered or in reset

      Checks

      1. 1Check the supply and ground of the sending unit with the key on
      2. 2Inspect the connector and wiring for chafe, moisture and loose pins
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

    • Deutz SPN 523009 FMI 10Fuel pressure relief valve: Abnormal rate of change

      The EMR4 sees the fuel pressure relief valve (on the common rail, opening to relieve excess pressure back to tank) change at an abnormal rate, faster or slower than the physical system can.· Erratic or implausible
      Check soon

      Causes

      • Intermittent contact causing sudden jumps
      • Sensor or part failing

      Checks

      1. 1Watch the fuel pressure relief valve value in SerDia and note jumps that do not match the machine behaviour
      2. 2Wiggle the harness and connectors while watching the live value
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

    • Deutz SPN 523470 FMI 2Fuel pressure relief valve: Erratic reading

      The EMR4 sees the pressure relief valve (PRV) on the rail (on the common rail, opening to relieve excess pressure back to tank) behave erratically against the command, which can mean a sticking part or an intermittent connection.· Erratic or implausible
      Stop now

      Causes

      • Valve coil connector corroded from fuel seepage
      • Valve seat worn or held open by dirt
      • Valve stuck open or closed from fuel contamination

      Checks

      1. 1Check the return flow from the PRV; any steady flow while the engine idles means the valve is leaking
      2. 2Check both connector halves of the pressure relief valve (PRV) on the rail for loose, bent or fretted pins
      3. 3Read rail pressure in SerDia: if it will not hold against target, a leaking relief valve is a prime suspect
      4. 4Wiggle the pressure relief valve (PRV) on the rail harness and connector while watching the live status in SerDia for dropouts
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Engine - Fuel pressure relief valve - Data erratic intermittent or incorrect

    • Deutz SPN 523470 FMI 7Fuel pressure relief valve: Not responding / out of adjustment

      The EMR4 sees the pressure relief valve (PRV) on the rail (on the common rail, opening to relieve excess pressure back to tank) not following its commanded position or movement.· Part or controller
      Stop now

      Causes

      • Valve stuck open or closed from fuel contamination
      • Valve coil connector corroded from fuel seepage
      • Valve seat worn or held open by dirt

      Checks

      1. 1Inspect for soot, oil or foreign matter around the part
      2. 2Read rail pressure in SerDia: if it will not hold against target, a leaking relief valve is a prime suspect
      3. 3Command it from SerDia and watch actual position against commanded
      4. 4Move the part by hand with the key off to see whether it is stuck
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

      Source wording:Engine - Fuel pressure relief valve - Mechanical system not responding or out of adjustment

      Full page for SPN 523470 FMI 7
    • Deutz SPN 523470 FMI 11Fuel pressure relief valve: Root cause not known

      The EMR4 logged a fault on the pressure relief valve (PRV) on the rail (on the common rail, opening to relieve excess pressure back to tank) but could not classify the cause.· Other
      Stop now

      Causes

      • Valve coil connector corroded from fuel seepage
      • Failing pressure relief valve (PRV) on the rail
      • Valve seat worn or held open by dirt
      • Intermittent wiring fault

      Checks

      1. 1Read rail pressure in SerDia: if it will not hold against target, a leaking relief valve is a prime suspect
      2. 2Inspect the pressure relief valve (PRV) on the rail plug and harness for chafed insulation, bent pins and moisture
      3. 3Measure the supply and ground at the pressure relief valve (PRV) on the rail plug with the key on to confirm it is powered
      4. 4Check the return flow from the PRV; any steady flow while the engine idles means the valve is leaking
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

    • Deutz SPN 523470 FMI 12Fuel pressure relief valve: Bad device or component

      The EMR4 judges the pressure relief valve (PRV) on the rail (on the common rail, opening to relieve excess pressure back to tank) to be a bad device, meaning the part or its driver electronics no longer respond as a working component.· Part or controller
      Stop now

      Causes

      • Driver stage in the EMR4 failing
      • Internal failure of the pressure relief valve (PRV) on the rail
      • Water or soot inside the part
      • Valve seat worn or held open by dirt

      Checks

      1. 1Measure supply voltage and ground at the pressure relief valve (PRV) on the rail connector with the key on to confirm the part is powered
      2. 2Fit a known good pressure relief valve (PRV) on the rail if you can borrow one and see whether the code clears for good
      3. 3Read rail pressure in SerDia: if it will not hold against target, a leaking relief valve is a prime suspect
      4. 4Read the pressure relief valve (PRV) on the rail status in SerDia and run any actuator test
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

      Source wording:Engine - Fuel pressure relief valve - Bad intelligent device or component

    • Deutz SPN 523470 FMI 13Fuel pressure relief valve: Out of calibration

      The EMR4 reports the pressure relief valve (PRV) on the rail (on the common rail, opening to relieve excess pressure back to tank) as out of calibration.· Part or controller
      Stop now

      Causes

      • Mechanical wear or play shifting the end positions
      • Valve coil connector corroded from fuel seepage
      • Pressure relief valve (PRV) on the rail replaced without a recalibration

      Checks

      1. 1Check the pressure relief valve (PRV) on the rail for mechanical play or a loose linkage that shifts its end positions
      2. 2Run the end-position learn or calibration routine in SerDia, if your service tool offers it for the pressure relief valve (PRV) on the rail
      3. 3Replace the pressure relief valve (PRV) on the rail if the end-position learn routine in SerDia fails repeatedly
      4. 4Read rail pressure in SerDia: if it will not hold against target, a leaking relief valve is a prime suspect
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Deutz SPN 523470 FMI 14Fuel pressure relief valve: Special instructions

      The EMR4 flags the pressure relief valve (PRV) on the rail (on the common rail, opening to relieve excess pressure back to tank) as a special instruction case.· Other
      Stop now

      Causes

      • Valve seat worn or held open by dirt
      • Valve coil connector corroded from fuel seepage
      • A running condition the EMR4 monitors

      Checks

      1. 1Read rail pressure in SerDia: if it will not hold against target, a leaking relief valve is a prime suspect
      2. 2Check the machine service manual for the special instruction
      3. 3Check the return flow from the PRV; any steady flow while the engine idles means the valve is leaking
      4. 4Read the full SerDia list and the freeze frame data
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Fuel pressure3 codes

    • Deutz SPN 523613 FMI 0Fuel pressure: Reading too high· most severe

      The EMR4 sees the monitored fuel (rail) pressure above its allowed range.· Real condition
      Stop now

      Causes

      • Fuel metering unit (FMU) on the high-pressure pump stuck open or over-delivering
      • Pressure relief valve (PRV) on the rail stuck closed
      • Rail pressure sensor reading low, so the EMR4 keeps raising pressure
      • Blocked fuel return line holding pressure up

      Checks

      1. 1Read rail pressure actual versus target in SerDia at idle; actual far above target points at an uncontrolled supply
      2. 2Check that the PRV on the rail opens and has not seized shut
      3. 3Check the FMU coil resistance and the FMU connector on the pump for contamination
      4. 4Test the rail pressure sensor against a known value with key on and engine off
      5. 5Look for a kinked or blocked return line to the tank
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Engine - Fuel pressure - Data above normal operational range (Most severe level)

    • Deutz SPN 523613 FMI 1Fuel pressure: Reading too low· most severe

      The EMR4 sees the monitored fuel (rail) pressure below its allowed range.· Real condition
      Stop now

      Causes

      • Plugged fuel filter or air in the low-pressure side starving the pump
      • Leaking injector or leaking rail connection
      • Pressure relief valve (PRV) leaking back to tank
      • High-pressure pump worn or its fuel metering unit under-delivering

      Checks

      1. 1Prime and bleed the low-pressure side, then change both fuel filters
      2. 2Check the fuel return flow from the injectors and the PRV; excess return flow means an internal leak
      3. 3Look for diesel wet spots on the rail, lines and injector fittings
      4. 4Watch rail pressure in SerDia while cranking; it should climb quickly
      5. 5Check the FMU duty cycle in SerDia; if it is maxed out the pump cannot keep up
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:Engine - Fuel pressure - Data below normal operational range (Most severe level)

      Full page for SPN 523613 FMI 1
    • Deutz SPN 523613 FMI 2Fuel pressure: Erratic reading

      The EMR4 sees the monitored rail pressure erratic or not plausible against its commanded value.· Erratic or implausible
      Check soon

      Causes

      • Air in the low-pressure fuel circuit
      • Rail pressure sensor signal intermittent from a loose connector
      • Leaking injector or relief valve making pressure wander
      • Partly blocked fuel filter

      Checks

      1. 1Bleed the low-pressure side and check the suction line for air leaks, a very common cause of swinging rail pressure
      2. 2Watch rail pressure actual in SerDia while moving the rail sensor harness, to rule out a loose connector
      3. 3Check the injector return flow for a weak or leaking injector that makes the pressure wander
      4. 4Change both fuel filters and test again, since a partly blocked filter starves the pump unevenly
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:Engine - Fuel pressure - Data erratic intermittent or incorrect

  • Fuel metering unit4 codes

    • Deutz SPN 523615 FMI 3Fuel metering unit: Voltage high / shorted high

      The EMR4 sees the output for the fuel metering unit (FMU) (on the high-pressure pump, where it meters fuel into the pump) at a voltage above normal, as if the circuit is shorted to the battery supply.· Shorted high
      Stop now

      Causes

      • Connector on the high-pressure pump soaked in diesel
      • Fuel metering unit (FMU) shorted internally
      • Connector pin touching a live pin

      Checks

      1. 1Measure the winding or coil resistance of the part
      2. 2Inspect the FMU connector and the harness where it passes the pump for diesel wetting and chafing
      3. 3With the EMR4 unplugged, measure the output wire to battery positive; it should be open
      4. 4Check rail pressure actual and target in SerDia while cranking to see whether the FMU is being driven at all
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Engine - Fuel metering unit - Voltage above normal or shorted to high source

      Full page for SPN 523615 FMI 3
    • Deutz SPN 523615 FMI 4Fuel metering unit: Voltage low / shorted low

      The EMR4 sees the output for the fuel metering unit (FMU) (on the high-pressure pump, where it meters fuel into the pump) at a voltage below normal, as if the circuit is shorted to ground.· Shorted low
      Stop now

      Causes

      • Connector on the high-pressure pump soaked in diesel
      • Fuel metering unit (FMU) winding shorted to its housing
      • Water in the connector bridging the pins

      Checks

      1. 1Unplug the fuel metering unit (FMU): if the code changes, the part is the shorted one; if it stays, look at the harness
      2. 2Check rail pressure actual and target in SerDia while cranking to see whether the FMU is being driven at all
      3. 3Measure the winding resistance of the part and look for a very low value
      4. 4Inspect the FMU connector and the harness where it passes the pump for diesel wetting and chafing
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Engine - Fuel metering unit - Voltage below normal or shorted to low source

    • Deutz SPN 523615 FMI 5Fuel metering unit: Current low / open circuit

      The EMR4 sees too little current through the fuel metering unit (FMU) (on the high-pressure pump, where it meters fuel into the pump), which means the circuit is open.· Open circuit
      Stop now

      Causes

      • Fuel metering unit (FMU) winding open
      • Connector left unplugged after earlier work
      • Broken wire or a pin pushed out of the connector

      Checks

      1. 1Inspect the FMU connector and the harness where it passes the pump for diesel wetting and chafing
      2. 2Check rail pressure actual and target in SerDia while cranking to see whether the FMU is being driven at all
      3. 3Continuity-test each wire to the matching EMR4 pin
      4. 4Measure the resistance across the fuel metering unit (FMU) terminals: infinity means an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

      Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

      Source wording:Engine - Fuel metering unit - Current below normal or open circuit

    • Deutz SPN 523615 FMI 12Fuel metering unit: Bad device or component

      The EMR4 judges the fuel metering unit (FMU) (on the high-pressure pump, where it meters fuel into the pump) to be a bad device, meaning the part or its driver electronics no longer respond as a working component.· Part or controller
      Stop now

      Causes

      • Internal failure of the fuel metering unit (FMU)
      • Water or soot inside the part
      • Driver stage in the EMR4 failing
      • Connector on the high-pressure pump soaked in diesel

      Checks

      1. 1Fit a known good fuel metering unit (FMU) if you can borrow one and see whether the code clears for good
      2. 2Check rail pressure actual and target in SerDia while cranking to see whether the FMU is being driven at all
      3. 3Read the fuel metering unit (FMU) status in SerDia and run any actuator test
      4. 4Inspect the FMU connector and the harness where it passes the pump for diesel wetting and chafing
      5. 5Measure supply voltage and ground at the fuel metering unit (FMU) connector with the key on to confirm the part is powered
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

      Source wording:Engine - Fuel metering unit - Bad intelligent device or component

  • Fuel pre feed pump4 codes

    • Deutz SPN 523906 FMI 3Fuel pre feed pump: Voltage high / shorted high

      The EMR4 sees the output for the fuel pre-feed pump (in the low-pressure fuel system, supplying the high-pressure pump) at a voltage above normal, as if the circuit is shorted to the battery supply.· Shorted high
      Check soon

      Causes

      • Fuel pre-feed pump shorted internally
      • Pump running dry or sucking air
      • Connector pin touching a live pin

      Checks

      1. 1With the EMR4 unplugged, measure the output wire to battery positive; it should be open
      2. 2Check the fuel filter and suction line for restrictions and air leaks
      3. 3Measure the winding or coil resistance of the part
      4. 4Listen for the pump running at key-on and check feed pressure in SerDia
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:Engine - Fuel pre feed pump - Voltage above normal or shorted to high source

    • Deutz SPN 523906 FMI 4Fuel pre feed pump: Voltage low / shorted low

      The EMR4 sees the output for the fuel pre-feed pump (in the low-pressure fuel system, supplying the high-pressure pump) at a voltage below normal, as if the circuit is shorted to ground.· Shorted low
      Check soon

      Causes

      • Pump running dry or sucking air
      • Output wire chafed to ground or the engine block
      • Fuel pre-feed pump winding shorted to its housing

      Checks

      1. 1Listen for the pump running at key-on and check feed pressure in SerDia
      2. 2With the EMR4 unplugged, measure the output wire to ground; it should not be low ohms
      3. 3Check the fuel filter and suction line for restrictions and air leaks
      4. 4Measure the winding resistance of the part and look for a very low value
      5. 5Unplug the fuel pre-feed pump: if the code changes, the part is the shorted one; if it stays, look at the harness
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:Engine - Fuel pre feed pump - Voltage below normal or shorted to low source

    • Deutz SPN 523906 FMI 5Fuel pre feed pump: Current low / open circuit

      The EMR4 sees too little current through the fuel pre-feed pump (in the low-pressure fuel system, supplying the high-pressure pump), which means the circuit is open.· Open circuit
      Check soon

      Causes

      • Broken wire or a pin pushed out of the connector
      • Pump running dry or sucking air
      • Connector left unplugged after earlier work

      Checks

      1. 1Listen for the pump running at key-on and check feed pressure in SerDia
      2. 2Check the fuel filter and suction line for restrictions and air leaks
      3. 3Measure the resistance across the fuel pre-feed pump terminals: infinity means an open winding
      4. 4Inspect both ends of the fuel pre-feed pump circuit (EMR4 plug and part connector) for pins pushed back in the housing
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

      Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

      Source wording:Engine - Fuel pre feed pump - Current below normal or open circuit

    • Deutz SPN 523906 FMI 12Fuel pre feed pump: Bad device or component

      The EMR4 judges the fuel pre-feed pump (in the low-pressure fuel system, supplying the high-pressure pump) to be a bad device, meaning the part or its driver electronics no longer respond as a working component.· Part or controller
      Check soon

      Causes

      • Pump running dry or sucking air
      • Water or soot inside the part
      • Internal failure of the fuel pre-feed pump

      Checks

      1. 1Check the fuel filter and suction line for restrictions and air leaks
      2. 2Listen for the pump running at key-on and check feed pressure in SerDia
      3. 3Fit a known good fuel pre-feed pump if you can borrow one and see whether the code clears for good
      4. 4Read the fuel pre-feed pump status in SerDia and run any actuator test
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

      Source wording:Engine - Fuel pre feed pump - Bad intelligent device or component

Shared checks

Checks, in order

  1. 1Read rail pressure actual against target in SerDia while cranking and under load
  2. 2With key on and engine off, rail pressure should read near zero; a large offset points at the sensor
  3. 3Change the fuel filters, bleed the low-pressure side and check the pre-feed pump delivery
  4. 4Measure the coil resistance of the metering unit and the relief valve and check their plugs
  5. 5Look for diesel wetness around the rail and fittings; a leak here is a safety item

Causes

  • Air or a restriction on the low-pressure side starving the high-pressure pump
  • Fuel metering unit coil open, shorted or its plug corroded
  • Rail sensor leaking or its connector contaminated with diesel
  • Relief valve stuck open or opened by genuine over-pressure

Most common here: part or controller (5 of 22)

Check power and ground at the module connector with the key on, then its fuses.

When to stop

You'll notice: A warning lamp or limited function.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.