Deutz · High-pressure fuel system
Deutz Fault Code SPN 164 FMI 2
Engine - Rail pressure - Data erratic intermittent or incorrect
What does Deutz code SPN 164 FMI 2 mean?
The EMR4 sees the rail pressure signal erratic. The common rail pressure swings or fails a plausibility check, so the controller cannot hold a steady pressure. Urgency: check soon - the machine may derate or limit a function. Check first: bleed the low-pressure side and check for air at the suction side of the feed pump.
- FMI 2
- Erratic or incorrect data
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Bleed the low-pressure side and check for air at the suction side of the feed pump
Then 3 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 4 done
Causes
- Air in the fuel or a starved high-pressure pump
- Failing rail pressure sensor with a noisy signal
- Intermittent sensor connector contact
- Worn high-pressure pump losing pressure under load
How it failed
You'll notice: Rough running, loss of power and sometimes a stall under load; the warning lamp comes on.
Erratic or implausibleRead from FMI 2: erratic or incorrect data
The reading jumps, drifts or disagrees with the sensors around it.
- Meter test
- Watch the live value on the service tool while you flex the harness and tap the connector.
- Good result
- A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Common rail: metering unit, pre-feed pump, relief valve and rail pressure
3 other codes on this part are also erratic or implausible (SPN 523009 FMI 10, SPN 523470 FMI 2, SPN 523613 FMI 2). When they show together, start at the wiring and connector they share.
- SPN 157 FMI 3Engine - Rail pressure sensor - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 157 FMI 4Engine - Rail pressure sensor - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 164 FMI 2Engine - Rail pressure - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 523009 FMI 9Engine - Fuel pressure relief valve - Abnormal update rate timeoutLost messageCheck soon
- SPN 523009 FMI 10Engine - Fuel pressure relief valve - Abnormal rate of changeErratic or implausibleCheck soon
- SPN 523470 FMI 2Engine - Fuel pressure relief valve - Data erratic intermittent or incorrectErratic or implausibleStop now
- SPN 523470 FMI 7Engine - Fuel pressure relief valve - Mechanical system not responding or out of adjustmentPart or controllerStop now
- SPN 523470 FMI 11Engine - Fuel pressure relief valve - Root cause not knownOtherStop now
- SPN 523470 FMI 12Engine - Fuel pressure relief valve - Bad intelligent device or componentPart or controllerStop now
Show the other 13 codesHide the other codes
- SPN 523470 FMI 13Engine - Fuel pressure relief valve - Out of calibrationPart or controllerStop now
- SPN 523470 FMI 14Engine - Fuel pressure relief valve - Special instructionsOtherStop now
- SPN 523613 FMI 0Engine - Fuel pressure - Data above normal operational range (Most severe level)Real conditionStop now
- SPN 523613 FMI 1Engine - Fuel pressure - Data below normal operational range (Most severe level)Real conditionStop now
- SPN 523613 FMI 2Engine - Fuel pressure - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 523615 FMI 3Engine - Fuel metering unit - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 523615 FMI 4Engine - Fuel metering unit - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 523615 FMI 5Engine - Fuel metering unit - Current below normal or open circuitOpen circuitStop now
- SPN 523615 FMI 12Engine - Fuel metering unit - Bad intelligent device or componentPart or controllerStop now
- SPN 523906 FMI 3Engine - Fuel pre feed pump - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 523906 FMI 4Engine - Fuel pre feed pump - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 523906 FMI 5Engine - Fuel pre feed pump - Current below normal or open circuitOpen circuitCheck soon
- SPN 523906 FMI 12Engine - Fuel pre feed pump - Bad intelligent device or componentPart or controllerCheck soon
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 30
This source lists SPN 164 FMI 2 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
