J1939 · Fuel system
SPN 164 Fault Code
Engine injection control pressure
What does SPN 164 mean?
Fuel rail pressure used for injection control, read by the rail pressure sensor. The ECM compares it with its target and regulates the high-pressure pump to match. How urgent it is depends on the FMI after SPN 164 - pick it below. Check first: compare the injection control pressure with the commanded pressure at cranking and under load.
- SPN 164
- Engine injection control pressure
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 164 - pick it below.
What should I check first?
Compare the injection control pressure with the commanded pressure at cranking and under load
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 164?
You'll notice: The ECM cannot trust the injection control pressure on a Detroit-style rail, so it limits fuelling to protect the system.
Find the number shown after SPN 164 on your display. 2 of them have their own page with causes and checks.
- 2SPN 164 FMI 2: Rail pressure sensor reading has drifted high compared with the real pressureErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 3SPN 164 FMI 3: Rail pressure sensor circuit is open or reads highShorted highDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 4SPN 164 FMI 4: Rail pressure sensor circuit is shorted to ground and reads lowShorted lowDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 5SPN 164 FMI 5: Rail pressure sensor circuit is open or stuck within rangeOpen circuitDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 15SPN 164 FMI 15: Actual rail pressure differs from the target by more than 200 bar under loadReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 20SPN 164 FMI 20: Rail pressure sensor has drifted highErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 21SPN 164 FMI 21: Rail pressure sensor has drifted lowErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
Checks
0 of 5 done
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
How urgent SPN 164 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Sensor circuit (FMI 3/4): signal wire open, shorted to the supply or to ground between the rail pressure sensor and the ECM
- Pressure error (FMI 15): actual rail pressure differs from the target by more than the limit under load, usually from supply or pump problems
- Erratic or drifting reading (FMI 2/20/21): sensor drifting high or low against the true pressure or a loose plug
- Open circuit (FMI 5): sensor plug off or pin backed out at the rail
Other Fuel system codes
Source
Detroit Diesel DD15 2017-2020 fault codes list (Diesel Laptops)
This list names SPN 164 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Detroit DD13 and DD15 (2017-2020); same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
