Deutz · High-pressure fuel system
Deutz Fault Code SPN 523470 FMI 7
Engine - Fuel pressure relief valve - Mechanical system not responding or out of adjustment
What does Deutz code SPN 523470 FMI 7 mean?
The EMR4 sees the pressure relief valve (PRV) on the rail (on the common rail, opening to relieve excess pressure back to tank) not following its commanded position or movement. The signal is fine; the part itself is not moving as it should. Urgency: stop now - shut down and fix before working on. Check first: inspect for soot, oil or foreign matter around the part.
- SPN 523470
- What is at fault
- FMI 7
- Mechanical system not responding
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Inspect for soot, oil or foreign matter around the part
Then 3 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 4 done
Causes
- Valve stuck open or closed from fuel contamination
- Valve coil connector corroded from fuel seepage
- Valve seat worn or held open by dirt
How it failed
You'll notice: Power loss or limited operation: rail pressure may spike or the engine may run in limp mode with reduced power while the valve is out of action.
Part or controllerRead from FMI 7: mechanical system not responding
The controller reports a part, module or its software as faulty or not responding.
- Meter test
- Check power and ground at the module connector with the key on, then its fuses.
- Good result
- Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Common rail: metering unit, pre-feed pump, relief valve and rail pressure
4 other codes on this part are also part or controller (SPN 523470 FMI 12, SPN 523470 FMI 13, SPN 523615 FMI 12, SPN 523906 FMI 12). When they show together, start at the wiring and connector they share.
- SPN 164 FMI 2Engine - Rail pressure - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 523009 FMI 9Engine - Fuel pressure relief valve - Abnormal update rate timeoutLost messageCheck soon
- SPN 523009 FMI 10Engine - Fuel pressure relief valve - Abnormal rate of changeErratic or implausibleCheck soon
- SPN 523470 FMI 2Engine - Fuel pressure relief valve - Data erratic intermittent or incorrectErratic or implausibleStop now
- SPN 523470 FMI 7Engine - Fuel pressure relief valve - Mechanical system not responding or out of adjustmentPart or controllerStop now
- SPN 523470 FMI 11Engine - Fuel pressure relief valve - Root cause not knownOtherStop now
- SPN 523470 FMI 12Engine - Fuel pressure relief valve - Bad intelligent device or componentPart or controllerStop now
- SPN 523470 FMI 13Engine - Fuel pressure relief valve - Out of calibrationPart or controllerStop now
- SPN 523470 FMI 14Engine - Fuel pressure relief valve - Special instructionsOtherStop now
Show the other 13 codesHide the other codes
- SPN 157 FMI 3Engine - Rail pressure sensor - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 157 FMI 4Engine - Rail pressure sensor - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 523613 FMI 0Engine - Fuel pressure - Data above normal operational range (Most severe level)Real conditionStop now
- SPN 523613 FMI 1Engine - Fuel pressure - Data below normal operational range (Most severe level)Real conditionStop now
- SPN 523613 FMI 2Engine - Fuel pressure - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 523615 FMI 3Engine - Fuel metering unit - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 523615 FMI 4Engine - Fuel metering unit - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 523615 FMI 5Engine - Fuel metering unit - Current below normal or open circuitOpen circuitStop now
- SPN 523615 FMI 12Engine - Fuel metering unit - Bad intelligent device or componentPart or controllerStop now
- SPN 523906 FMI 3Engine - Fuel pre feed pump - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 523906 FMI 4Engine - Fuel pre feed pump - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 523906 FMI 5Engine - Fuel pre feed pump - Current below normal or open circuitOpen circuitCheck soon
- SPN 523906 FMI 12Engine - Fuel pre feed pump - Bad intelligent device or componentPart or controllerCheck soon
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 16
This source lists SPN 523470 FMI 7 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
