Deutz · High-pressure fuel system
Deutz Fault Code SPN 523613 FMI 1
Engine - Fuel pressure - Data below normal operational range (Most severe level)
What does Deutz code SPN 523613 FMI 1 mean?
The EMR4 sees the monitored fuel (rail) pressure below its allowed range. The high-pressure circuit is not building or holding the pressure the engine needs for the requested load. Urgency: stop now - shut down and fix before working on. Check first: prime and bleed the low-pressure side, then change both fuel filters.
- SPN 523613
- What is at fault
- FMI 1
- Data below normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Prime and bleed the low-pressure side, then change both fuel filters
Then 4 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 5 done
Causes
- Plugged fuel filter or air in the low-pressure side starving the pump
- Leaking injector or leaking rail connection
- Pressure relief valve (PRV) leaking back to tank
- High-pressure pump worn or its fuel metering unit under-delivering
How it failed
You'll notice: Hard starting, no start, loss of power or a stall; the engine may run in limp mode while pressure stays low.
Real conditionRead from FMI 1: data below normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Common rail: metering unit, pre-feed pump, relief valve and rail pressure
1 other code on this part is also real condition (SPN 523613 FMI 0). When they show together, start at the wiring and connector they share.
- SPN 523470 FMI 12Engine - Fuel pressure relief valve - Bad intelligent device or componentPart or controllerStop now
- SPN 523470 FMI 13Engine - Fuel pressure relief valve - Out of calibrationPart or controllerStop now
- SPN 523470 FMI 14Engine - Fuel pressure relief valve - Special instructionsOtherStop now
- SPN 523613 FMI 0Engine - Fuel pressure - Data above normal operational range (Most severe level)Real conditionStop now
- SPN 523613 FMI 1Engine - Fuel pressure - Data below normal operational range (Most severe level)Real conditionStop now
- SPN 523613 FMI 2Engine - Fuel pressure - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 523615 FMI 3Engine - Fuel metering unit - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 523615 FMI 4Engine - Fuel metering unit - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 523615 FMI 5Engine - Fuel metering unit - Current below normal or open circuitOpen circuitStop now
Show the other 13 codesHide the other codes
- SPN 157 FMI 3Engine - Rail pressure sensor - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 157 FMI 4Engine - Rail pressure sensor - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 164 FMI 2Engine - Rail pressure - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 523009 FMI 9Engine - Fuel pressure relief valve - Abnormal update rate timeoutLost messageCheck soon
- SPN 523009 FMI 10Engine - Fuel pressure relief valve - Abnormal rate of changeErratic or implausibleCheck soon
- SPN 523470 FMI 2Engine - Fuel pressure relief valve - Data erratic intermittent or incorrectErratic or implausibleStop now
- SPN 523470 FMI 7Engine - Fuel pressure relief valve - Mechanical system not responding or out of adjustmentPart or controllerStop now
- SPN 523470 FMI 11Engine - Fuel pressure relief valve - Root cause not knownOtherStop now
- SPN 523615 FMI 12Engine - Fuel metering unit - Bad intelligent device or componentPart or controllerStop now
- SPN 523906 FMI 3Engine - Fuel pre feed pump - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 523906 FMI 4Engine - Fuel pre feed pump - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 523906 FMI 5Engine - Fuel pre feed pump - Current below normal or open circuitOpen circuitCheck soon
- SPN 523906 FMI 12Engine - Fuel pre feed pump - Bad intelligent device or componentPart or controllerCheck soon
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 16
This source lists SPN 523613 FMI 1 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
