Deutz · Exhaust aftertreatment (SCR)
Deutz Collective faults and power reduction (Main and Secondary ECU) fault codes
On a twin-controller engine an SCR, DEF or hardware fault on one controller is reported to the other as a collective fault, and after it has stayed open the inducement logic cuts power in steps. The codes name which controller raised the collective fault and which error triggered it (DEF tank, SCR, dosing, reverting valve), and the power reduction steps and announcements (SPN 524190, 524191, 524230 to 524232, 524267).
More about these partsLess
They are consequences of another fault, not first causes.
Where to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
What do these codes mean?
Deutz codes SPN 524190 FMI 14 to SPN 524267 FMI 14 are all about the collective faults and power reduction (Main and Secondary ECU). None needs an immediate stop. Start with this check: open the fault list of the other controller first, because every code here follows from an entry there.
How urgent are they?
None of the 26 codes here means stop now; 25 can wait until the shift ends, but find the cause before the next one; 1 is information only.
- Check soon25
- Info1
What should I check first?
Open the fault list of the other controller first, because every code here follows from an entry there
Shared checks26 of 26
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Engine - Power reduction step 11 code
Deutz SPN 524190 FMI 14Engine - Power reduction step 1: Special instructions
The EMR4 flags engine power reduction step 1 as special instructions. The controller has started a first stage of derating because of a monitored fault. Deutz list: KWP code 1891, blink code 272. Step 1 of the power reduction has been reached: the engine is now limited in the first stage, and the countdown toward step 2 is running.· OtherOtherCheck soonCauses
- An active aftertreatment or emission fault
- A protection fault such as a temperature limit
- DEF quality or level warning
Checks
- 1Read all active codes in SerDia; this entry accompanies a root-cause fault, so find that first
- 2Fix the root-cause fault and clear the codes, since the derate lifts when the cause is gone
- 3Check the DEF level and quality if SCR faults are active
- 4Check the aftertreatment sensors for plausibility before replacing parts
- 5Read which fault started the countdown and repair that fault before the second step is reached.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Engine - Power reduction step 21 code
Deutz SPN 524191 FMI 14Engine - Power reduction step 2: Special instructions
The EMR4 flags engine power reduction step 2 as special instructions. The controller has moved to a second, deeper stage of derating. Deutz list: KWP code 1892, blink code 273. Step 2 of the power reduction has been reached, the deeper limit, which also reduces the maximum torque the machine can call for.· Lost messageLost messageCheck soonCauses
- An unresolved emission or protection fault
- DEF empty or poor quality
- Persistent aftertreatment failure
Checks
- 1Read all active codes in SerDia and find the original fault that led to this deeper derate
- 2Check the DEF level and quality with a refractometer, since empty or poor DEF often causes this step
- 3Check the aftertreatment sensors (NOx, temperature, pressure) for plausibility
- 4Fix the root cause, then clear the codes and confirm full power returns
- 5Repair the fault that started the reduction, then confirm in SerDia that the step counter falls back.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Exhaust aftertreatment - Secondary collective error triggered by DEF tank error Main ECU1 code
Deutz SPN 524201 FMI 11Exhaust aftertreatment - Secondary collective error triggered by DEF tank error Main ECU: Root cause not known
The Secondary and Main controllers exchange status, and the EMR4 logged an event for the secondary collective error triggered by DEF tank error Main ECU (on engines with a Main and a Secondary ECU, raised after a Main ECU SCR or DEF error) with a cause it could not name. It is usually a consequence of another fault on the other controller. Deutz list: KWP code 1942, blink code 3-1-3. The Secondary ECU raised a collective error because the Main ECU reported a DEF tank error, so the first fault is in the tank unit on the Main side.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the stored faults of the other controller and start with the oldest
- 2Fix that fault, then clear both controllers and test run the engine
- 3Read the DEF tank level, temperature and quality faults on the Main ECU.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Exhaust aftertreatment - Collective fault on Secondary ECU triggered by SCR failure Main5 codes
Deutz SPN 524202 FMI 11Exhaust aftertreatment - Collective fault on Secondary ECU triggered by SCR failure Main: Root cause not known
The Secondary and Main controllers exchange status, and the EMR4 logged an event for the collective fault on Secondary ECU triggered by SCR failure Main (on engines with a Main and a Secondary ECU, raised after a Main ECU SCR or DEF error) with a cause it could not name. It is usually a consequence of another fault on the other controller. Deutz list: KWP code 1943, blink code 3-1-3. The Secondary ECU raised a collective fault because the Main ECU saw an SCR failure; the catalyst, dosing or NOx faults on the Main side are the first fault.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the stored faults of the other controller and start with the oldest
- 2Fix that fault, then clear both controllers and test run the engine
- 3Read the SCR, dosing and NOx faults stored on the Main ECU.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524204 FMI 11Exhaust aftertreatment - Collective fault on Secondary ECU triggered by SCR failure Main: Root cause not known
Same fault as SPN 524202 FMI 11 for the Collective fault on Secondary ECU triggered by SCR failure Main message. The Secondary ECU raised a collective fault because the Main ECU saw an SCR failure; the catalyst, dosing or NOx faults on the Main side are the first fault. Deutz list: KWP code 1945, blink code 3-1-3.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the SCR, dosing and NOx faults stored on the Main ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524205 FMI 11Exhaust aftertreatment - Collective fault on Secondary ECU triggered by SCR failure Main: Root cause not known
Same fault as SPN 524202 FMI 11 for the Collective fault on Secondary ECU triggered by SCR failure Main message. The Secondary ECU raised a collective fault because the Main ECU saw an SCR failure; the catalyst, dosing or NOx faults on the Main side are the first fault. Deutz list: KWP code 1946, blink code 3-1-3.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the SCR, dosing and NOx faults stored on the Main ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524239 FMI 11Exhaust aftertreatment - Collective fault on Secondary ECU triggered by SCR failure Main: Root cause not known
Same fault as SPN 524202 FMI 11 for the Collective fault on Secondary ECU triggered by SCR failure Main message. The Secondary ECU raised a collective fault because the Main ECU saw an SCR failure; the catalyst, dosing or NOx faults on the Main side are the first fault. Deutz list: KWP code 1980, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the SCR, dosing and NOx faults stored on the Main ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524248 FMI 11Exhaust aftertreatment - Collective fault on Secondary ECU triggered by SCR failure Main: Root cause not known
Same fault as SPN 524202 FMI 11 for the Collective fault on Secondary ECU triggered by SCR failure Main message. The Secondary ECU raised a collective fault because the Main ECU saw an SCR failure; the catalyst, dosing or NOx faults on the Main side are the first fault. Deutz list: KWP code 1989, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the SCR, dosing and NOx faults stored on the Main ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Exhaust aftertreatment - Collective fault on Secondary ECU triggered DEF tank failure Main1 code
Deutz SPN 524203 FMI 11Exhaust aftertreatment - Collective fault on Secondary ECU triggered DEF tank failure Main: Root cause not known
The Secondary and Main controllers exchange status, and the EMR4 logged an event for the collective fault on Secondary ECU triggered DEF tank failure Main (on engines with a Main and a Secondary ECU, raised after a Main ECU SCR or DEF error) with a cause it could not name. It is usually a consequence of another fault on the other controller. Deutz list: KWP code 1944, blink code 3-1-3. The Secondary ECU raised a collective fault because the Main ECU saw a DEF tank failure.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the stored faults of the other controller and start with the oldest
- 2Fix that fault, then clear both controllers and test run the engine
- 3Check the DEF tank unit, heater and level faults on the Main ECU.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Exhaust aftertreatment - Collective fault on Secondary ECU triggered by DEF dosing failure Main1 code
Deutz SPN 524206 FMI 11Exhaust aftertreatment - Collective fault on Secondary ECU triggered by DEF dosing failure Main: Root cause not known
The Secondary and Main controllers exchange status, and the EMR4 logged an event for the collective fault on Secondary ECU triggered by DEF dosing failure Main (on engines with a Main and a Secondary ECU, raised after a Main ECU SCR or DEF error) with a cause it could not name. It is usually a consequence of another fault on the other controller. Deutz list: KWP code 1947, blink code 3-1-3. The Secondary ECU raised a collective fault because the Main ECU saw a DEF dosing failure, so look at the dosing module and pump on the Main side.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the stored faults of the other controller and start with the oldest
- 2Fix that fault, then clear both controllers and test run the engine
- 3Read the DEF metering unit and pump faults on the Main ECU.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Exhaust aftertreatment - Hardware failure on Secondary ECU activates power reduction1 code
Deutz SPN 524230 FMI 11Exhaust aftertreatment - Hardware failure on Secondary ECU activates power reduction: Root cause not known
The Secondary and Main controllers exchange status, and the EMR4 logged an event for the hardware failure on Secondary ECU activates power reduction (on engines with a Main and a Secondary ECU) with a cause it could not name. It is usually a consequence of another fault on the other controller. Deutz list: KWP code 1971, blink code 3-1-5. The Secondary ECU reports a hardware failure of its own and requested a power reduction, so its internal electronics are the suspect.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the stored faults of the other controller and start with the oldest
- 2Fix that fault, then clear both controllers and test run the engine
- 3Check supply, ground and connectors of the Secondary ECU first, then have the controller tested.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Exhaust aftertreatment - SCR failure on Secondary ECU activates power reduction2 codes
Deutz SPN 524231 FMI 11Exhaust aftertreatment - SCR failure on Secondary ECU activates power reduction: Root cause not known
The Secondary and Main controllers exchange status, and the EMR4 logged an event for the SCR failure on Secondary ECU activates power reduction (on engines with a Main and a Secondary ECU) with a cause it could not name. It is usually a consequence of another fault on the other controller. Deutz list: KWP code 1972, blink code 3-1-5. An SCR failure on the Secondary ECU started a power reduction, so the SCR parts it controls are the first fault.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the stored faults of the other controller and start with the oldest
- 2Fix that fault, then clear both controllers and test run the engine
- 3Read the SCR faults stored on the Secondary ECU.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524232 FMI 11Exhaust aftertreatment - SCR failure on Secondary ECU activates power reduction: Root cause not known
Same fault as SPN 524231 FMI 11 for the SCR failure on Secondary ECU activates power reduction message. An SCR failure on the Secondary ECU started a power reduction, so the SCR parts it controls are the first fault. Deutz list: KWP code 1973, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the SCR faults stored on the Secondary ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Exhaust aftertreatment - Collective fault on Main ECU triggered by SCR failure Secondary5 codes
Deutz SPN 524249 FMI 11Exhaust aftertreatment - Collective fault on Main ECU triggered by SCR failure Secondary: Root cause not known
The Secondary and Main controllers exchange status, and the EMR4 logged an event for the collective fault on Main ECU triggered by SCR failure Secondary (on engines with a Main and a Secondary ECU, raised after a Secondary ECU SCR or DEF error) with a cause it could not name. It is usually a consequence of another fault on the other controller. Deutz list: KWP code 1990, blink code 3-1-5. The Main ECU raised a collective fault because the Secondary ECU saw an SCR failure, so the catalyst or NOx parts on the Secondary side come first.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the stored faults of the other controller and start with the oldest
- 2Fix that fault, then clear both controllers and test run the engine
- 3Read the SCR and NOx faults stored on the Secondary ECU.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524251 FMI 11Exhaust aftertreatment - Collective fault on Main ECU triggered by SCR failure Secondary: Root cause not known
Same fault as SPN 524249 FMI 11 for the Collective fault on Main ECU triggered by SCR failure Secondary message. The Main ECU raised a collective fault because the Secondary ECU saw an SCR failure, so the catalyst or NOx parts on the Secondary side come first. Deutz list: KWP code 1992, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the SCR and NOx faults stored on the Secondary ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524254 FMI 11Exhaust aftertreatment - Collective fault on Main ECU triggered by SCR failure Secondary: Root cause not known
Same fault as SPN 524249 FMI 11 for the Collective fault on Main ECU triggered by SCR failure Secondary message. The Main ECU raised a collective fault because the Secondary ECU saw an SCR failure, so the catalyst or NOx parts on the Secondary side come first. Deutz list: KWP code 1995, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the SCR and NOx faults stored on the Secondary ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524257 FMI 11Exhaust aftertreatment - Collective fault on Main ECU triggered by SCR failure Secondary: Root cause not known
Same fault as SPN 524249 FMI 11 for the Collective fault on Main ECU triggered by SCR failure Secondary message. The Main ECU raised a collective fault because the Secondary ECU saw an SCR failure, so the catalyst or NOx parts on the Secondary side come first. Deutz list: KWP code 1998, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the SCR and NOx faults stored on the Secondary ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524258 FMI 11Exhaust aftertreatment - Collective fault on Main ECU triggered by SCR failure Secondary: Root cause not known
Same fault as SPN 524249 FMI 11 for the Collective fault on Main ECU triggered by SCR failure Secondary message. The Main ECU raised a collective fault because the Secondary ECU saw an SCR failure, so the catalyst or NOx parts on the Secondary side come first. Deutz list: KWP code 1999, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the SCR and NOx faults stored on the Secondary ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Exhaust aftertreatment - Reverting valve failure on Secondary ECU triggered by collective fault Main1 code
Deutz SPN 524252 FMI 11Exhaust aftertreatment - Reverting valve failure on Secondary ECU triggered by collective fault Main: Root cause not known
The Secondary and Main controllers exchange status, and the EMR4 logged an event for the reverting valve failure on Secondary ECU triggered by collective fault Main (on engines with a Main and a Secondary ECU, raised after a Main ECU SCR or DEF error) with a cause it could not name. It is usually a consequence of another fault on the other controller. Deutz list: KWP code 1993, blink code 3-1-5. The reverting valve, which reverses DEF flow to empty the lines, failed on the Secondary ECU and raised a collective fault on the Main ECU.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the stored faults of the other controller and start with the oldest
- 2Fix that fault, then clear both controllers and test run the engine
- 3Check the reverting valve and its circuit on the Secondary side.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Exhaust aftertreatment - Collective fault on Main ECU triggered by DEF failure Secondary6 codes
Deutz SPN 524253 FMI 11Exhaust aftertreatment - Collective fault on Main ECU triggered by DEF failure Secondary: Root cause not known
The Secondary and Main controllers exchange status, and the EMR4 logged an event for the collective fault on Main ECU triggered by DEF failure Secondary (on engines with a Main and a Secondary ECU, raised after a Secondary ECU SCR or DEF error) with a cause it could not name. It is usually a consequence of another fault on the other controller. Deutz list: KWP code 1994, blink code 3-1-5. The Main ECU raised a collective fault because the Secondary ECU saw a DEF failure, so the pump, line, heater or tank on the Secondary side come first.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the stored faults of the other controller and start with the oldest
- 2Fix that fault, then clear both controllers and test run the engine
- 3Read the DEF pump, heater and tank faults stored on the Secondary ECU.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524255 FMI 11Exhaust aftertreatment - Collective fault on Main ECU triggered by DEF failure Secondary: Root cause not known
Same fault as SPN 524253 FMI 11 for the Collective fault on Main ECU triggered by DEF failure Secondary message. The Main ECU raised a collective fault because the Secondary ECU saw a DEF failure, so the pump, line, heater or tank on the Secondary side come first. Deutz list: KWP code 1996, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the DEF pump, heater and tank faults stored on the Secondary ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524256 FMI 11Exhaust aftertreatment - Collective fault on Main ECU triggered by DEF failure Secondary: Root cause not known
Same fault as SPN 524253 FMI 11 for the Collective fault on Main ECU triggered by DEF failure Secondary message. The Main ECU raised a collective fault because the Secondary ECU saw a DEF failure, so the pump, line, heater or tank on the Secondary side come first. Deutz list: KWP code 1997, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the DEF pump, heater and tank faults stored on the Secondary ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524259 FMI 11Exhaust aftertreatment - Collective fault on Main ECU triggered by DEF failure Secondary: Root cause not known
Same fault as SPN 524253 FMI 11 for the Collective fault on Main ECU triggered by DEF failure Secondary message. The Main ECU raised a collective fault because the Secondary ECU saw a DEF failure, so the pump, line, heater or tank on the Secondary side come first. Deutz list: KWP code 2000, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the DEF pump, heater and tank faults stored on the Secondary ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524260 FMI 11Exhaust aftertreatment - Collective fault on Main ECU triggered by DEF failure Secondary: Root cause not known
Same fault as SPN 524253 FMI 11 for the Collective fault on Main ECU triggered by DEF failure Secondary message. The Main ECU raised a collective fault because the Secondary ECU saw a DEF failure, so the pump, line, heater or tank on the Secondary side come first. Deutz list: KWP code 2001, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the DEF pump, heater and tank faults stored on the Secondary ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Deutz SPN 524261 FMI 11Exhaust aftertreatment - Collective fault on Main ECU triggered by DEF failure Secondary: Root cause not known
Same fault as SPN 524253 FMI 11 for the Collective fault on Main ECU triggered by DEF failure Secondary message. The Main ECU raised a collective fault because the Secondary ECU saw a DEF failure, so the pump, line, heater or tank on the Secondary side come first. Deutz list: KWP code 2002, blink code 3-1-5.· OtherOtherCheck soonCauses
- The original fault is stored on the other controller
- Interrupted CAN link or supply between the two controllers
Checks
- 1Read the DEF pump, heater and tank faults stored on the Secondary ECU.
- 2Read the stored faults of the other controller and start with the oldest
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Exhaust aftertreatment - Announcement trigger power reduction step 21 code
Deutz SPN 524267 FMI 14Exhaust aftertreatment - Announcement trigger power reduction step 2: Special instructions
The EMR4 flags the announcement trigger power reduction step 2 (in the EMR4 inducement logic) as a special instruction case. This is an informational or conditional event rather than a standard wiring fault. Deutz list: KWP code 2007, blink code 273. This code is the warning that step 2 of the power reduction is about to start; the power is not yet cut but will be if nothing is done.· OtherOtherInfoCauses
- A running condition that the EMR4 monitors has been reached
- An earlier fault left a stored special instruction
Checks
- 1Read the full SerDia list and the freeze frame data
- 2Check the machine service manual for the instruction that belongs to this condition
- 3Use the time of the announcement to clear the underlying DEF or SCR fault before power drops.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Open the fault list of the other controller first, because every code here follows from an entry there
- 2Repair the DEF tank, SCR or dosing fault you find, then clear both controllers
- 3If the entry returns with nothing on the other controller, check the link between them
- 4Check the power reduction counter in SerDia, then run the engine under load and confirm full power returns
Causes
- An SCR, DEF tank, dosing or reverting valve fault stored on the other controller and passed on
- CAN link interrupted, so the entry never cleared
- One controller cleared without the other, leaving a stale collective entry
- A warning ignored long enough to escalate to power reduction
When to stop
You'll notice: A warning lamp and, if the fault stays, reduced engine power until the original fault on the other controller is repaired.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
