Deutz · ECU hardware
Deutz Fault Code SPN 523612 FMI 12
Engine - ECU - Bad intelligent device or component
What does Deutz code SPN 523612 FMI 12 mean?
The EMR4 reports itself as a bad intelligent device. An internal self-test has failed, so the controller is considered defective. Urgency: stop now - shut down and fix before working on. Check first: check the ECU connector and housing for water and corrosion.
- SPN 523612
- What is at fault
- FMI 12
- Bad intelligent device or component
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Check the ECU connector and housing for water and corrosion
Then 3 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 4 done
Causes
- Internal hardware failure in the EMR4
- Voltage spike from a jump-start or alternator fault
- Water ingress into the ECU housing
- Failed flash or software
How it failed
You'll notice: The engine may refuse to start or shut down, and cycling the key does not clear the code.
Part or controllerRead from FMI 12: bad intelligent device or component
The controller reports a part, module or its software as faulty or not responding.
- Meter test
- Check power and ground at the module connector with the key on, then its fuses.
- Good result
- Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: EMR4 controller, memory, supply and immobilizer
8 other codes on this part are also part or controller (SPN 630 FMI 12, SPN 1079 FMI 13, SPN 1080 FMI 13, SPN 523601 FMI 13 and more). When they show together, start at the wiring and connector they share.
- SPN 523330 FMI 14Engine - Immobilizer - Special instructionsOtherCheck soon
- SPN 523601 FMI 13Engine - ECU Sensor supply voltage 3 - Out of calibrationPart or controllerCheck soon
- SPN 523612 FMI 3Engine - ECU - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 523612 FMI 4Engine - ECU - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 523612 FMI 12Engine - ECU - Bad intelligent device or componentPart or controllerStop now
- SPN 523612 FMI 14Engine - ECU - Special instructionsOtherCheck soon
- SPN 523704 FMI 12Engine - Engine controller 3 - Bad intelligent device or componentPart or controllerCheck soon
- SPN 523935 FMI 12Engine - Engine controller 3 - Bad intelligent device or componentPart or controllerCheck soon
- SPN 523936 FMI 12Engine - Engine controller 3 - Bad intelligent device or componentPart or controllerCheck soon
Show the other 16 codesHide the other codes
- SPN 168 FMI 0Machine - Battery voltage - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 168 FMI 1Machine - Battery voltage - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 168 FMI 2Machine - Battery voltage - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 168 FMI 3Machine - Battery voltage - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 168 FMI 4Machine - Battery voltage - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 630 FMI 12Engine - ECU calibration memory - Bad intelligent device or componentPart or controllerStop now
- SPN 1079 FMI 13Engine - Sensor supply voltage - Out of calibrationPart or controllerCheck soon
- SPN 1080 FMI 13Engine - Sensor supply voltage 2 - Out of calibrationPart or controllerCheck soon
- SPN 1136 FMI 0Engine - ECU temperature - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 523008 FMI 1Engine - Manipulation monitoring - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 523008 FMI 2Engine - Manipulation monitoring - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 524052 FMI 11Engine - Dataset Main and Secondary ECU not identical - Root cause not knownOtherCheck soon
- SPN 524068 FMI 2Engine - ECU Main Secondary identical - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 524233 FMI 11Engine - ECU EEPROM error Secondary - Root cause not knownPart or controllerCheck soon
- SPN 524277 FMI 11Engine - ECU afterun too often not waited - Root cause not knownOtherCheck soon
- SPN 524278 FMI 11Engine - ECU afterun too often consecutive not waited - Root cause not knownOtherCheck soon
Other Deutz codes: ECU hardware
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 6
This source lists SPN 523612 FMI 12 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
