EF Logo

Deutz · Exhaust aftertreatment (SCR)

Deutz Fault Code SPN 3361 FMI 4

Exhaust aftertreatment - DEF metering unit - Voltage below normal or shorted to low source

What does Deutz code SPN 3361 FMI 4 mean?

The EMR4 sees the output for the DEF metering valve (dosing valve) (at the exhaust pipe in front of the SCR catalyst, injecting DEF) at a voltage below normal, as if the circuit is shorted to ground. Urgency: check soon - the machine may derate or limit a function. Check first: check the dosing valve for crystal deposits at the nozzle and for a spray pattern during a dosing test.

FaultCheckSPN 3361FMI 4Deutz · Exhaust aftertreatment (SCR)
FMI 4
Voltage below normal or shorted low

Can I keep running with it?

Check soon

The machine may derate or limit a function. Find the cause before the next shift.

What should I check first?

Check the dosing valve for crystal deposits at the nozzle and for a spray pattern during a dosing test

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.

Checks

0 of 5 done

Causes

  • Water in the connector bridging the pins
  • DEF metering valve (dosing valve) winding shorted to its housing
  • Dosing nozzle blocked by crystallised DEF

How it failed

You'll notice: Expect a warning lamp; DEF cannot be injected, so NOx is not reduced; the SCR lamp comes on and power is reduced after a countdown.

Shorted lowRead from FMI 4: voltage below normal or shorted low

The signal sits at or near zero volts - less than a working sensor can send.

ControllerPartSupplySignalGround
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.
Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good result
Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

When to stop

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Same part, other failures: DEF pump, metering unit and suction unit

3 other codes on this part are also shorted low (SPN 3361 FMI 6, SPN 4375 FMI 4, SPN 4376 FMI 4). When they show together, start at the wiring and connector they share.

Show the other 13 codes
All 22 DEF pump, metering unit and suction unit codes on one page

Source

DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 22

This source lists SPN 3361 FMI 4 and its meaning. The guidance on this page is general, not taken from it.

The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.