J1939 · Aftertreatment - SCR/DEF
SPN 3361 Fault Code
Aftertreatment 1 diesel exhaust fluid dosing unit
What does SPN 3361 mean?
The unit that pressurises and meters DEF into the exhaust, with its pump, valves and sensors. The aftertreatment control uses it to dose the SCR system. How urgent it is depends on the FMI after SPN 3361 - pick it below. Check first: run the DEF dosing or purge test with the service tool and listen for the pump and the valve clicking.
- SPN 3361
- Aftertreatment 1 diesel exhaust fluid dosing unit
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 3361 - pick it below.
What should I check first?
Run the DEF dosing or purge test with the service tool and listen for the pump and the valve clicking
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 3361?
You'll notice: The DEF dosing unit has reported an error or failed its self-check, so DEF is not injected into the exhaust.
Find the number shown after SPN 3361 on your display.
- 1SPN 3361 FMI 1: The automatic self-check of the DEF dosing system was not completedReal conditionDetroit DD13 Gen 5, Detroit DD15 Gen 5
- 2SPN 3361 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15
- 3SPN 3361 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Detroit DD15
- 4SPN 3361 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15
- 5SPN 3361 FMI 5: Current is below normal, or the circuit is openOpen circuitCummins ISX15, Detroit DD15
- 11SPN 3361 FMI 11: A fault exists but the ECM cannot identify its causeOtherCummins ISX15
- 12SPN 3361 FMI 12: Bad intelligent device or componentPart or controllerCummins ISX15
- 31SPN 3361 FMI 31: The DEF dosing unit reports an errorReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 3361 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Dosing unit power, ground or CAN wiring fault: corroded plug, chafed lead or blown fuse on the dosing module supply
- Dosing valve nozzle blocked by crystallised DEF, so the unit cannot deliver and flags a flow error
- DEF frozen in the unit or its lines after a cold soak, with the heater not thawing it
- Internal failure in the dosing unit pump, valve driver or pressure sensor
Other Aftertreatment - SCR/DEF codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 3361 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
