EF Logo

J1939 · Aftertreatment - SCR/DEF

SPN 5394 Fault Code

Aftertreatment 1 diesel exhaust fluid dosing valve

What does SPN 5394 mean?

The valve that injects metered DEF into the exhaust stream, driven by the dosing controller. The control watches its circuit and response. How urgent it is depends on the FMI after SPN 5394 - pick it below. Check first: run the dosing test and watch the valve current and the pressure change as it pulses.

FaultActiveSPN 5394FMI --J1939 engine ECU
SPN 5394
Aftertreatment 1 diesel exhaust fluid dosing valve
FMI ?
How it failed - the number after the SPN

Can I keep running with it?

Depends on the FMI

How urgent it is depends on the FMI after SPN 5394 - pick it below.

What should I check first?

Run the dosing test and watch the valve current and the pressure change as it pulses

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a J1939-capable scan tool to the 9-pin diagnostic port.

Which FMI shows after SPN 5394?

You'll notice: The DEF dosing valve is not opening and closing as commanded, so too little or too much DEF reaches the exhaust.

Find the number shown after SPN 5394 on your display.

  • 0SPN 5394 FMI 0: Value is above the normal range, most severe levelReal conditionMack MP8, Mack MP7, Volvo D13
  • 1SPN 5394 FMI 1: Value is below the normal range, most severe levelReal conditionMack MP8, Mack MP7, Volvo D13
  • 2SPN 5394 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15
  • 3SPN 5394 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Mack MP8, Mack MP7, Volvo D13
  • 4SPN 5394 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Mack MP8, Mack MP7, Volvo D13
  • 5SPN 5394 FMI 5: Current is below normal, or the circuit is openOpen circuitCummins ISX15, Mack MP8, Mack MP7, PACCAR MX-13 and 1 more
  • 7SPN 5394 FMI 7: The mechanical part is not responding or is out of adjustmentPart or controllerCummins ISX15, PACCAR MX-13
  • 14SPN 5394 FMI 14: A special-instruction condition defined by the engine maker appliesOtherMack MP8, Mack MP7, Volvo D13
  • 17SPN 5394 FMI 17: Value is below the normal range, least severe levelReal conditionMack MP8, Mack MP7, Volvo D13

Checks

0 of 5 done

When to stop

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

How urgent SPN 5394 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Causes

  • Dosing valve coil open or shorted, or its plug corroded, so the ECM sees a wrong current
  • Valve tip clogged with crystallised DEF, restricting the spray
  • Valve stuck open or closed from contamination in the DEF
  • DEF supply pressure too low or air in the line, so the valve cannot dose correctly

Source

Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)

This list names SPN 5394 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.

The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.