J1939 · Aftertreatment - SCR/DEF
SPN 3364 Fault Code
Aftertreatment 1 diesel exhaust fluid quality
What does SPN 3364 mean?
A measure of the DEF concentration and condition, from a quality sensor in the tank or inferred from NOx. The aftertreatment control uses it to catch diluted or wrong fluid. How urgent it is depends on the FMI after SPN 3364 - pick it below. Check first: check the DEF sample against clean DEF with a refractometer; good fluid with a quality fault points to the sensor or its circuit.
- SPN 3364
- Aftertreatment 1 diesel exhaust fluid quality
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 3364 - pick it below.
What should I check first?
Check the DEF sample against clean DEF with a refractometer; good fluid with a quality fault points to the sensor or its circuit
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 3364?
You'll notice: The ECM cannot judge DEF quality, so it may warn of poor fluid and then start inducement, with a lamp and derate even if the fluid is good.
Find the number shown after SPN 3364 on your display. 3 of them have their own page with causes and checks.
- 1SPN 3364 FMI 1: DEF quality final warning, so the ECM has judged the fluid improperReal conditionDetroit DD15
- 2SPN 3364 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15
- 3SPN 3364 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, PACCAR MX-13
- 4SPN 3364 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, PACCAR MX-13
- 9SPN 3364 FMI 9: Abnormal update rate: the signal or message is late or missingLost messageCummins ISX15
- 10SPN 3364 FMI 10: DEF quality data is updating at an abnormal rateErratic or implausibleCummins ISX15
- 11SPN 3364 FMI 11: A fault exists but the ECM cannot identify its causeOtherCummins ISX15
- 13SPN 3364 FMI 13: The value is out of calibrationPart or controllerCummins ISX15
- 15SPN 3364 FMI 15: Value is above the normal range, least severe levelReal conditionCummins ISX15
- 17SPN 3364 FMI 17: DEF quality warning: the fluid is judged improperReal conditionDetroit DD15
- 18SPN 3364 FMI 18: Value is below the normal range, moderately severe levelReal conditionCummins ISX15
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 3364 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Signal high or open: open signal or return wire, or the signal touching a supply wire, at the DEF quality sensor
- Signal low or shorted: signal wire grounded, or the supply to the DEF quality sensor lost
- Real condition: diluted or contaminated DEF that really is poor quality
- Real condition: wrong fluid in the tank after a top-up
1 more causeFewer causes
- Sensor: air bubbles or sloshing in the tank giving a noisy quality reading
Other Aftertreatment - SCR/DEF codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 3364 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
