Deutz · Exhaust aftertreatment (SCR)
Deutz Fault Code SPN 4375 FMI 3
Exhaust aftertreatment - DEF pump - Voltage above normal or shorted to high source
What does Deutz code SPN 4375 FMI 3 mean?
The EMR4 sees the output for the DEF pump (in the SCR dosing module that pumps DEF (AdBlue) to the dosing valve) at a voltage above normal, as if the circuit is shorted to the battery supply. The controller cannot drive the actuator correctly. Urgency: check soon - the machine may derate or limit a function. Check first: measure the winding or coil resistance of the part.
- FMI 3
- Voltage above normal or shorted high
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Measure the winding or coil resistance of the part
Then 3 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 4 done
Causes
- Output wire shorted to battery positive
- DEF pump shorted internally
- Connector pin touching a live pin
How it failed
You'll notice: Expect a warning lamp; DEF cannot be pumped to the dosing valve, so NOx rises; the SCR lamp comes on and power may be reduced after a countdown.
Shorted highRead from FMI 3: voltage above normal or shorted high
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DEF pump, metering unit and suction unit
2 other codes on this part are also shorted high (SPN 3361 FMI 3, SPN 4376 FMI 3). When they show together, start at the wiring and connector they share.
- SPN 3361 FMI 4Exhaust aftertreatment - DEF metering unit - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 3361 FMI 6Exhaust aftertreatment - DEF metering unit - Current above normal or grounded circuitShorted lowCheck soon
- SPN 3361 FMI 7Exhaust aftertreatment - DEF metering unit - Mechanical system not responding or out of adjustmentPart or controllerCheck soon
- SPN 4374 FMI 13Exhaust aftertreatment - DEF metering valve - Out of calibrationPart or controllerCheck soon
- SPN 4375 FMI 3Exhaust aftertreatment - DEF pump - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 4375 FMI 4Exhaust aftertreatment - DEF pump - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 4375 FMI 5Exhaust aftertreatment - DEF pump - Current below normal or open circuitOpen circuitCheck soon
- SPN 4376 FMI 3Exhaust aftertreatment - DEF reverse valve - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 4376 FMI 4Exhaust aftertreatment - DEF reverse valve - Voltage below normal or shorted to low sourceShorted lowCheck soon
Show the other 13 codesHide the other codes
- SPN 3361 FMI 3Exhaust aftertreatment - DEF metering unit - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 4376 FMI 5Exhaust aftertreatment - DEF reverse valve - Current below normal or open circuitOpen circuitCheck soon
- SPN 4376 FMI 12Exhaust aftertreatment - DEF reverse valve - Bad intelligent device or componentPart or controllerCheck soon
- SPN 523668 FMI 11Exhaust aftertreatment - Hardware failure temperature sensor DEF suction unit - Root cause not knownOtherCheck soon
- SPN 523669 FMI 11Exhaust aftertreatment - Hardware failure quality sensor DEF suction unit - Root cause not knownOtherCheck soon
- SPN 523670 FMI 11Exhaust aftertreatment - Hardware failure level sensor DEF suction unit - Root cause not knownOtherCheck soon
- SPN 523720 FMI 2Exhaust aftertreatment - Heater DEF metering unit - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 523720 FMI 8Exhaust aftertreatment - Heater DEF metering unit - Abnormal frequency or pulse width or periodErratic or implausibleCheck soon
- SPN 524067 FMI 0Exhaust aftertreatment - DEF pump temperature - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 524067 FMI 1Exhaust aftertreatment - DEF pump temperature - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 524067 FMI 2Exhaust aftertreatment - DEF pump temperature - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 524141 FMI 7Exhaust aftertreatment - DEF metering valve - Mechanical system not responding or out of adjustmentPart or controllerCheck soon
- SPN 524282 FMI 11Exhaust aftertreatment - Hardware failure temperature sensor DEF suction unit - Root cause not knownOtherCheck soon
Other Deutz codes: Exhaust aftertreatment (SCR)
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 24
This source lists SPN 4375 FMI 3 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
