Deutz · Exhaust aftertreatment (DPF/DOC)
Deutz Fault Code SPN 3251 FMI 0
Exhaust aftertreatment - DPF differential pressure - Data above normal operational range (Most severe level)
What does Deutz code SPN 3251 FMI 0 mean?
The DPF differential pressure (across the diesel particulate filter) reports a value above the allowed range. This is a plausibility limit, so the high value may be genuine rather than a wiring fault. Urgency: check soon - the machine may derate or limit a function. Check first: check the real value against a mechanical gauge or second reading before touching the DPF differential pressure.
- FMI 0
- Data above normal, most severe
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the real value against a mechanical gauge or second reading before touching the DPF differential pressure
Then 4 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 5 done
Causes
- A heavily loaded or ash-plugged DPF causes a genuine high differential pressure; check the regeneration history
- Hose or port feeding the sensor blocked with dirt
- Cracked or missing filter substrate leaking exhaust past the element
How it failed
You'll notice: Warning or derate: the EMR4 sees a pressure drop across the DPF that is out of range; the DPF lamp can light and power can be reduced until regeneration or service is done.
Real conditionRead from FMI 0: data above normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DPF differential pressure, DPF and DOC temperature, and DPF load
6 other codes on this part are also real condition (SPN 3251 FMI 1, SPN 3699 FMI 0, SPN 4765 FMI 0, SPN 4766 FMI 0 and more). When they show together, start at the wiring and connector they share.
- SPN 3248 FMI 4Exhaust aftertreatment - Temperature after DPF - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 3251 FMI 0Exhaust aftertreatment - DPF differential pressure - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 3251 FMI 1Exhaust aftertreatment - DPF differential pressure - Data below normal operational range (Most severe level)Real conditionCheck soon
- SPN 3253 FMI 2Exhaust aftertreatment - DPF differential pressure - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 3253 FMI 3Exhaust aftertreatment - DPF differential pressure - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 3253 FMI 4Exhaust aftertreatment - DPF differential pressure - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 3699 FMI 0Exhaust aftertreatment - Passive regeneration - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 3699 FMI 2Exhaust aftertreatment - Passive regeneration - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 4765 FMI 0Exhaust aftertreatment - Temperature upstream DOC - Data above normal operational range (Most severe level)Real conditionCheck soon
Show the other 15 codesHide the other codes
- SPN 4766 FMI 0Exhaust aftertreatment - Temperature downstream DOC - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 4768 FMI 2Exhaust aftertreatment - Temperature sensor before DOC - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 4768 FMI 3Exhaust aftertreatment - Temperature sensor before DOC - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 4768 FMI 4Exhaust aftertreatment - Temperature sensor before DOC - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 4769 FMI 2Exhaust aftertreatment - Temperature sensor after DOC - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 4769 FMI 3Exhaust aftertreatment - Temperature sensor after DOC - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 4769 FMI 4Exhaust aftertreatment - Temperature sensor after DOC - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 524018 FMI 14Exhaust aftertreatment - DPF regeneration request - Special instructionsOtherInformation
- SPN 524022 FMI 14Exhaust aftertreatment - Soot load - Special instructionsOtherInformation
- SPN 524024 FMI 11Exhaust aftertreatment - DOC temperature difference - Root cause not knownOtherCheck soon
- SPN 524134 FMI 0Exhaust aftertreatment - DPF ash load - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 524135 FMI 0Exhaust aftertreatment - DPF soot load - Data above normal operational range (Most severe level)Real conditionCheck soon
- SPN 524135 FMI 14Exhaust aftertreatment - DPF soot load - Special instructionsOtherInformation
- SPN 524283 FMI 12Exhaust aftertreatment - Swapped hoses for differential pressure sensor DPF - Bad intelligent device or componentPart or controllerCheck soon
- SPN 524284 FMI 12Exhaust aftertreatment - DOC removed - Bad intelligent device or componentPart or controllerCheck soon
Other Deutz codes: Exhaust aftertreatment (DPF/DOC)
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 15
This source lists SPN 3251 FMI 0 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
