EF Logo

Genie · Hydraulic coil and motor controller faults (H)

Genie Outrigger and platform extension deck coils fault codes

On the GS-3232 the outrigger extend and retract coils move all four outriggers together, and one extra coil per corner (left front, left rear, right front, right rear) lets the leveling routine move each leg on its own. On the GS-2646AV the power extension deck has extend, retract and enable valve coils on the PED harness.

More about these parts

The GCON ECM drives every one of these coils and reports shorts to either side of the battery and opens.

FaultCheckH049Genie · Outrigger and platform extension deck coils
Code shows hereFAULTH049

Where this code shows

Scissors: read the code on the platform LED display or the ground control LCD.

What do these codes mean?

Genie codes H049 to H115 are all about the outrigger and platform extension deck coils. Most are shorted high faults; 14 need an immediate stop. Start with this check: measure across the coil named by the code and compare it with the other coils of the same group; one outlier is the failed coil.

How urgent are they?

14 of 22 codes here mean stop now; the other 8 can wait until the shift ends, but find the cause before the next one.

  • Stop now14
  • Check soon8

What should I check first?

Measure across the coil named by the code and compare it with the other coils of the same group; one outlier is the failed coil.

Shared checks

22 of 22

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Genie H049Outrigger extend coil: short to battery negative

    The ECM sees the outrigger extend coil circuit with a short to battery negative.· Shorted high
    Check soon

    Causes

    • Outrigger extend coil: signal wire rubbed through to chassis ground, or the winding shorted to its housing
    • ECM driver output failed (rare)

    Checks

    1. 1Unplug the outrigger extend coil connector and cycle the key: if the code turns into the open-circuit one, the harness is clean and the coil is shorted. With the GCON plugs off, J1-7 (ground) to the coil pin must read above 5k ohm.
    2. 2Try outrigger retract: if it still works, the fault is limited to the extend coil circuit.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H050Outrigger extend coil: open circuit

    The ECM sees the outrigger extend coil circuit with a open circuit.· Open circuit
    Check soon

    Causes

    • Outrigger extend coil: coil winding burnt open, a broken wire or a pin backed out of the connector
    • ECM driver output failed (rare)

    Checks

    1. 1Measure across the outrigger extend coil terminals: an open reading means a failed coil, while a good coil with this code points at a broken wire. With the GCON plugs off, continuity from the ECM pin to the coil should be close to 0 ohm; reseat the connector and look for green corrosion on the pins.
    2. 2Try outrigger retract: if it still works, the fault is limited to the extend coil circuit.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Genie H051Outrigger extend coil: short to battery positive

    Same failure as H049 (short to supply), here on the outrigger extend coil: short to battery positive.· Shorted high
    Stop now

    Causes

    • Outrigger extend coil: signal wire touching a live supply wire, or the winding shorted to supply
    • ECM driver output failed (rare)

    Checks

    1. 1Unplug the outrigger extend coil connector: if the code changes to the open-circuit one, the coil or its plug caused the short. With the GCON plugs off, J1-12 (driver power) to the coil pin must read above 50k ohm; check the harness bundle for chafing against supply wires.
    2. 2Try outrigger retract: if it still works, the fault is limited to the extend coil circuit.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H052Outrigger retract coil: short to battery negative

    Same failure as H049 (short to supply), here on the outrigger retract coil: short to battery negative.· Shorted high
    Check soon

    Causes

    • Outrigger retract coil: signal wire rubbed through to chassis ground, or the winding shorted to its housing
    • ECM driver output failed (rare)

    Checks

    1. 1Unplug the outrigger retract coil connector and cycle the key: if the code turns into the open-circuit one, the harness is clean and the coil is shorted. With the GCON plugs off, J1-7 (ground) to the coil pin must read above 5k ohm.
    2. 2Try outrigger extend: if it still works, the fault is limited to the retract coil circuit.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H053Outrigger retract coil: open circuit

    Same failure as H050 (open circuit), here on the outrigger retract coil.· Open circuit
    Check soon

    Causes

    • Outrigger retract coil: coil winding burnt open, a broken wire or a pin backed out of the connector
    • ECM driver output failed (rare)

    Checks

    1. 1Measure across the outrigger retract coil terminals: an open reading means a failed coil, while a good coil with this code points at a broken wire. With the GCON plugs off, continuity from the ECM pin to the coil should be close to 0 ohm; reseat the connector and look for green corrosion on the pins.
    2. 2Try outrigger extend: if it still works, the fault is limited to the retract coil circuit.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Genie H054Outrigger retract coil: short to battery positive

    Same failure as H049 (short to supply), here on the outrigger retract coil: short to battery positive.· Shorted high
    Stop now

    Causes

    • Outrigger retract coil: signal wire touching a live supply wire, or the winding shorted to supply
    • ECM driver output failed (rare)

    Checks

    1. 1Unplug the outrigger retract coil connector: if the code changes to the open-circuit one, the coil or its plug caused the short. With the GCON plugs off, J1-12 (driver power) to the coil pin must read above 50k ohm; check the harness bundle for chafing against supply wires.
    2. 2Try outrigger extend: if it still works, the fault is limited to the retract coil circuit.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H057Left front outrigger coil: short to battery positive

    Same failure as H049 (short to supply), here on the left front outrigger coil: short to battery positive.· Shorted high
    Stop now

    Causes

    • Left front coil signal wire touching a live supply wire at the outrigger
    • Left front coil winding shorted to supply

    Checks

    1. 1Unplug the left front outrigger coil connector: if the code changes to the open-circuit one, the coil or its plug caused the short. With the GCON plugs off, J1-12 (driver power) to the coil pin must read above 50k ohm; check the harness bundle for chafing against supply wires. Do the same for the other three corners if this code repeats.
    2. 2Measure the coil and compare it with the other three corner coils, which are the same part; one outlier is the failed coil.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H060Left rear outrigger coil: short to battery positive

    Same fault as H057 on the left rear outrigger coil: the ECM sees its circuit shorted to battery positive.· Shorted high
    Stop now

    Causes

    • Left rear outrigger coil or its plug damaged
    • Harness fault on the left rear circuit

    Checks

    1. 1Measure the left rear outrigger coil and compare it with the other corners.
    2. 2Check the left rear circuit with the GCON plugs off for continuity and for shorts to ground or supply.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H063Right front outrigger coil: short to battery positive

    Same fault as H057 on the right front outrigger coil: the ECM sees its circuit shorted to battery positive.· Shorted high
    Stop now

    Causes

    • Right front outrigger coil or its plug damaged
    • Harness fault on the right front circuit

    Checks

    1. 1Measure the right front outrigger coil and compare it with the other corners.
    2. 2Check the right front circuit with the GCON plugs off for continuity and for shorts to ground or supply.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H066Right rear outrigger coil: short to battery positive

    Same fault as H057 on the right rear outrigger coil: the ECM sees its circuit shorted to battery positive.· Shorted high
    Stop now

    Causes

    • Right rear outrigger coil or its plug damaged
    • Harness fault on the right rear circuit

    Checks

    1. 1Measure the right rear outrigger coil and compare it with the other corners.
    2. 2Check the right rear circuit with the GCON plugs off for continuity and for shorts to ground or supply.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H074Left front outrigger coil: short or open

    Same failure as H050 (open circuit), here on the left front outrigger coil: short or.· Shorted high
    Check soon

    Causes

    • Left front coil winding shorted or open
    • Harness fault between the ECM and the left front coil

    Checks

    1. 1Measure across the left front outrigger coil terminals and compare with a good corner coil; because this code does not say which fault, a good coil sends you to the harness.
    2. 2With the GCON plugs off, check the circuit for continuity to the ECM and for shorts to ground or supply, and look for chafing on the harness near the valve.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H075Left rear outrigger coil: short or open

    Same fault as H074 on the left rear outrigger coil: the ECM sees its circuit shorted or open.· Other
    Check soon

    Causes

    • Left rear outrigger coil or its plug damaged
    • Harness fault on the left rear circuit

    Checks

    1. 1Measure the left rear outrigger coil and compare it with the other corners.
    2. 2Check the left rear circuit with the GCON plugs off for continuity and for shorts to ground or supply.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie H076Right front outrigger coil: short or open

    Same fault as H074 on the right front outrigger coil: the ECM sees its circuit shorted or open.· Other
    Check soon

    Causes

    • Right front outrigger coil or its plug damaged
    • Harness fault on the right front circuit

    Checks

    1. 1Measure the right front outrigger coil and compare it with the other corners.
    2. 2Check the right front circuit with the GCON plugs off for continuity and for shorts to ground or supply.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie H077Right rear outrigger coil: short or open

    Same fault as H074 on the right rear outrigger coil: the ECM sees its circuit shorted or open.· Other
    Check soon

    Causes

    • Right rear outrigger coil or its plug damaged
    • Harness fault on the right rear circuit

    Checks

    1. 1Measure the right rear outrigger coil and compare it with the other corners.
    2. 2Check the right rear circuit with the GCON plugs off for continuity and for shorts to ground or supply.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie H106Platform extend coil: short to battery negative

    Same failure as H049 (short to supply), here on the platform extend coil: short to battery negative.· Shorted high
    Stop now

    Causes

    • Platform extend coil: signal wire rubbed through to chassis ground, or the winding shorted to its housing
    • ECM driver output failed (rare)

    Checks

    1. 1Unplug the platform extend coil connector and cycle the key: if the code turns into the open-circuit one, the harness is clean and the coil is shorted. With the GCON plugs off, J1-7 (ground) to the coil pin must read above 5k ohm.
    2. 2Follow the PED harness along the deck pivot, where it flexes every time the deck moves, and flex it while watching the meter on the extend coil.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H107Platform extend coil: open circuit

    Same failure as H050 (open circuit), here on the platform extend coil.· Open circuit
    Stop now

    Causes

    • Platform extend coil: coil winding burnt open, a broken wire or a pin backed out of the connector
    • ECM driver output failed (rare)

    Checks

    1. 1Measure across the platform extend coil terminals: an open reading means a failed coil, while a good coil with this code points at a broken wire. With the GCON plugs off, continuity from the ECM pin to the coil should be close to 0 ohm; reseat the connector and look for green corrosion on the pins.
    2. 2Follow the PED harness along the deck pivot, where it flexes every time the deck moves, and flex it while watching the meter on the extend coil.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Genie H108Platform extend coil: short to battery positive

    Same failure as H049 (short to supply), here on the platform extend coil: short to battery positive.· Shorted high
    Stop now

    Causes

    • Platform extend coil: signal wire touching a live supply wire, or the winding shorted to supply
    • ECM driver output failed (rare)

    Checks

    1. 1Unplug the platform extend coil connector: if the code changes to the open-circuit one, the coil or its plug caused the short. With the GCON plugs off, J1-12 (driver power) to the coil pin must read above 50k ohm; check the harness bundle for chafing against supply wires.
    2. 2Follow the PED harness along the deck pivot, where it flexes every time the deck moves, and flex it while watching the meter on the extend coil.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H109Platform retract coil: short to battery negative

    Same failure as H049 (short to supply), here on the platform retract coil: short to battery negative.· Shorted high
    Stop now

    Causes

    • Platform retract coil: signal wire rubbed through to chassis ground, or the winding shorted to its housing
    • ECM driver output failed (rare)

    Checks

    1. 1Unplug the platform retract coil connector and cycle the key: if the code turns into the open-circuit one, the harness is clean and the coil is shorted. With the GCON plugs off, J1-7 (ground) to the coil pin must read above 5k ohm.
    2. 2Compare the retract coil reading with the extend coil on the same valve; the two should be close, and a large gap names the faulty one.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H110Platform retract coil: open circuit

    Same failure as H050 (open circuit), here on the platform retract coil.· Open circuit
    Stop now

    Causes

    • Platform retract coil: coil winding burnt open, a broken wire or a pin backed out of the connector
    • ECM driver output failed (rare)

    Checks

    1. 1Measure across the platform retract coil terminals: an open reading means a failed coil, while a good coil with this code points at a broken wire. With the GCON plugs off, continuity from the ECM pin to the coil should be close to 0 ohm; reseat the connector and look for green corrosion on the pins.
    2. 2Compare the retract coil reading with the extend coil on the same valve; the two should be close, and a large gap names the faulty one.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Genie H111Platform retract coil: short to battery positive

    Same failure as H049 (short to supply), here on the platform retract coil: short to battery positive.· Shorted high
    Stop now

    Causes

    • Platform retract coil: signal wire touching a live supply wire, or the winding shorted to supply
    • ECM driver output failed (rare)

    Checks

    1. 1Unplug the platform retract coil connector: if the code changes to the open-circuit one, the coil or its plug caused the short. With the GCON plugs off, J1-12 (driver power) to the coil pin must read above 50k ohm; check the harness bundle for chafing against supply wires.
    2. 2Compare the retract coil reading with the extend coil on the same valve; the two should be close, and a large gap names the faulty one.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H114Platform enable coil: short to battery positive

    Same failure as H049 (short to supply), here on the platform enable coil: short to battery positive.· Shorted high
    Stop now

    Causes

    • Platform enable coil: signal wire touching a live supply wire, or the winding shorted to supply
    • ECM driver output failed (rare)

    Checks

    1. 1Unplug the platform enable coil connector: if the code changes to the open-circuit one, the coil or its plug caused the short. With the GCON plugs off, J1-12 (driver power) to the coil pin must read above 50k ohm; check the harness bundle for chafing against supply wires.
    2. 2Command extend and retract in turn: if neither moves the deck, the enable coil circuit is the common fault.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie H115Platform enable coil: short circuit

    The ECM sees the PED platform enable circuit shorted; it cannot say to which side of the battery.· Short circuit
    Stop now

    Causes

    • Platform enable coil winding shorted or open
    • Harness fault to the enable coil in the PED harness
    • ECM driver output failed (rare)

    Checks

    1. 1Measure across the platform enable coil terminals and compare with the extend and retract coils on the same deck valve.
    2. 2With the GCON plugs off, check the enable circuit for continuity to the ECM and for shorts to ground or supply, then look for chafing at the deck pivot.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.

    Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.

Shared checks

Checks, in order

  1. 1Measure across the coil named by the code and compare it with the other coils of the same group; one outlier is the failed coil.
  2. 2Inspect the harness at the outrigger, or at the deck pivot for the PED, for chafing and crush damage.
  3. 3Unplug the coil and cycle the key: a short code that turns into the open-circuit code means the wire is clean and the coil is shorted.
  4. 4With the GCON plugs off, measure from J1-7 (ground) to the coil pin, which should read above 5k ohm, and from J1-12 (driver power) to the coil pin, which should read above 50k ohm.
  5. 5Replace the ECM only after the coil and wiring are proven good.

Causes

  • Coil for the named outrigger or deck valve damaged or wet
  • Harness chafed at the outrigger or where the PED harness flexes at the deck pivot
  • Connector pin loose or corroded
  • GCON ECM driver damaged (rare)

Most codes here: shorted high (14 of 22)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: The outriggers or the deck will not move, or all functions except platform down are blocked.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.