Genie · Sensor and limit switch faults (F)
Genie Fault Code F034
Height sensor not calibrated
What does Genie code F034 mean?
The height sensor settings are not calibrated for stowed and maximum height. All functions are blocked until the calibration is done. Urgency: stop now - shut down and fix before working on. Check first: run the height sensor calibration for stowed and maximum height from the service menu.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Run the height sensor calibration for stowed and maximum height from the service menu.
Then 3 more checksWhere this code shows
Scissors: read the code on the platform LED display or the ground control LCD.
Checks
0 of 4 done
Causes
- New or replaced height sensor
- New ECM or reflashed software without calibration
- Calibration lost after a software reset
- Sensor mounting moved after a repair
How it failed
You'll notice: Every function is blocked until the stowed and maximum platform heights are calibrated into the controller.
Part or controllerRead from how the source describes the code
The controller reports a part, module or its software as faulty or not responding.
- Meter test
- Check power and ground at the module connector with the key on, then its fuses.
- Good result
- Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Sensors and limit switches
2 other codes on this part are also part or controller (F035, F036). When they show together, start at the wiring and connector they share.
- F020Left rear outrigger sensor shorted to battery positiveShorted highCheck soon
- F021Left rear outrigger sensor shorted to battery negativeShorted highCheck soon
- F022Right rear outrigger sensor shorted to battery positiveShorted highCheck soon
- F023Right rear outrigger sensor shorted to battery negativeShorted highCheck soon
- F034Height sensor not calibratedPart or controllerStop now
- F035Height sensor below calibrated stowed valuePart or controllerStop now
- F036Height sensor above calibrated maximumPart or controllerStop now
- F072Function cutout sensor supply faultShorted highStop now
- F073Deck sensor supply faultShorted highStop now
Show the other 17 codesHide the other codes
- F001Up limit switch shortedOtherCheck soon
- F003Down limit switch shortedShorted highCheck soon
- F005Pothole limit switch shortedShorted highCheck soon
- F007Chassis tilt switch shortedShorted highCheck soon
- F008Overload transducer shorted highShorted highStop now
- F009Overload transducer shorted lowShorted lowStop now
- F010Platform height sensor shorted highShorted highCheck soon
- F011Platform height sensor shorted lowShorted lowCheck soon
- F012Level pitch sensor shorted to battery positiveShorted highStop now
- F013Level pitch sensor shorted to battery negativeShorted highStop now
- F014Level roll sensor shorted to battery positiveShorted highStop now
- F015Level roll sensor shorted to battery negativeShorted highStop now
- F016Left front outrigger sensor shorted to battery positiveShorted highCheck soon
- F017Left front outrigger sensor shorted to battery negativeShorted highCheck soon
- F018Right front outrigger sensor shorted to battery positiveShorted highCheck soon
- F019Right front outrigger sensor shorted to battery negativeShorted highCheck soon
- F129Tilt sensor mismatch (UTS)Real conditionStop now
Related on Equipments Finder
Source
This source lists F034 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Genie GS-1530/1532/1930/1932/2032/2632 slab scissors with SmartLink (GSDS) controls.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
