Genie · Control system fault codes (ALC-500 red/yellow LED)
Genie ALC-500 boom angle, load cell, limit switches and overload relays fault codes
These ALC-500 codes cover the inputs and safety outputs of the boom system: the boom angle sensor (error sources 24 and 26), the platform load cell for the overload system (76), the extend/retract limit switches (34 and 46), the drive enable override and platform level switches (44 and 45), and the overload cutout relays CR54, CR55 and CR56 that cut boom functions and the engine. Two further codes report a controller software mismatch and a lost hour meter.
Where this code shows
Scissors: read the code on the platform LED display or the ground control LCD.
What do these codes mean?
Genie codes 24-11 to 103-12 are all about the aLC-500 boom angle, load cell, limit switches and overload relays. Most are real condition faults; 12 need an immediate stop. Start with this check: check the wiring and connector of the named sensor, switch or relay for damage and corrosion.
How urgent are they?
12 of 25 codes here mean stop now; 12 can wait until the shift ends, but find the cause before the next one; 1 is information only.
- Stop now12
- Check soon12
- Info1
What should I check first?
Check the wiring and connector of the named sensor, switch or relay for damage and corrosion.
Shared checks25 of 25
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Genie 24-11Angle sensor at 5.0 V
The boom angle sensor reads 5.0 V. Boom speed is reduced and the alarm sounds until the sensor is repaired.· OtherOtherCheck soonCauses
- Angle sensor wiring shorted high
- Angle sensor failed
- Sensor connector corroded or loose
Checks
- 1Check the angle sensor connector at the boom pivot for water and loose pins.
- 2Measure the sensor signal to ground; it should change within 0.5-4.5 V as the boom moves, not stay at 5 V.
- 3Check the sensor has a good ground and a 5 V reference.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie 24-12Angle sensor value too high
The angle sensor reads too high. Reduced speed function applies and the alarm sounds.· Real conditionReal conditionCheck soonCauses
- Angle sensor wiring open or shorted
- Angle sensor failed
- Connector corroded
Checks
- 1Check the angle sensor connector and wiring.
- 2Measure the signal at several boom angles.
- 3Calibrate or replace the sensor.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 24-15Angle sensor value too low
The angle sensor reads too low. Reduced speed function applies and the alarm sounds.· Real conditionReal conditionCheck soonCauses
- Angle sensor wiring open or shorted
- Angle sensor failed
- Connector corroded
Checks
- 1Check the angle sensor connector and wiring.
- 2Measure the signal at several boom angles.
- 3Calibrate or replace the sensor.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 24-16Angle sensor value at 0 V
The angle sensor signal is at 0 V. Reduced speed function applies and the alarm sounds.· OtherOtherCheck soonCauses
- Angle sensor wiring open or shorted
- Angle sensor failed
- Connector corroded
Checks
- 1Check the angle sensor connector and wiring.
- 2Measure the signal at several boom angles.
- 3Calibrate or replace the sensor.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie 24-17Angle sensor not calibrated
The boom angle sensor is not calibrated and boom speed is reduced. It usually follows a sensor or controller replacement.· OtherOtherCheck soonCauses
- Angle sensor replaced without calibration
- Controller reset or software updated
- Calibration data lost
- Sensor mounting moved
Checks
- 1Run the boom angle sensor calibration from the service menu with the boom in the position the procedure calls for.
- 2Check the sensor mounting is tight and in its original position.
- 3After calibration, read the angle on the service screen and compare it with the real boom angle.
- 4Replace the angle sensor if it fails calibration or the reading does not follow the boom angle.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie 24-31Angle sensor invalid setup
The boom angle sensor setup is invalid. The alarm beeps for 1 second and the boom must retract into the safe envelope before it can continue.· Lost messageLost messageCheck soonCauses
- Angle sensor not set up after replacement
- Calibration lost or corrupted
- Sensor mounting moved or loose
Checks
- 1Calibrate the angle sensor from the service menu.
- 2Check the sensor bracket and fasteners are tight.
- 3Retract the boom into the safe envelope as prompted.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Genie 26-19Angle sensor cross check out of range
The two boom angle readings disagree, meaning the angle sensor cross check is out of range. Speed is reduced and the boom must retract into the safe envelope.· OtherOtherCheck soonCauses
- Angle sensor fault
- Wiring fault on one angle signal
- Sensor connector corroded
Checks
- 1Check both angle signals on the service screen; they should agree within the manual's tolerance.
- 2Inspect the sensor connector and wiring at the boom pivot for water and chafing.
- 3Check the sensor mounting is tight and not moved.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie 34-31Extend/retract limit switch invalid setup
The extend/retract limit switch setup is invalid and the alarm beeps for 1 second. In 1000 lb mode the boom must be fully retracted before lowering; 500 lb mode operates normally.· OtherOtherCheck soonCauses
- Limit switch not set up or misadjusted
- Extend/retract or fully stowed switch faulty
- Switch connector or wiring fault
Checks
- 1Fully retract the boom, then lower it, as the controller requires.
- 2Check the extend/retract and fully stowed limit switches are adjusted and clean.
- 3Meter each switch; it should change state as the boom retracts and extends.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie 34-36Extend/retract limit switch cross check fault
The primary boom retract limit switches disagree. The Overload LED is on, functions are cut and the engine shuts down. Auxiliary functions still work except extend.· Real conditionReal conditionStop nowCauses
- Primary boom retracted limit switch LS1 fault
- Safety limit switch LS5 fault
- Wiring fault on one of the limit switch circuits
Checks
- 1Check LS1 and LS5 for damage, correct adjustment and a clean mounting.
- 2With the boom retracted, expect 0 V at C42LS of LS1 and 12 V at C166LS of LS5.
- 3Extend the boom a small amount and recheck; both voltages should swap.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 44-21Drive enable override switch fault
The drive enable override switch is faulted, so the override direction is frozen at neutral. The fault clears after the switch is repaired and power is cycled.· OtherOtherCheck soonCauses
- Override switch stuck or broken
- Open wire between the override switch and the platform controller
- Water in the platform control box
Checks
- 1Move the drive enable override switch through its positions and check it springs back to neutral.
- 2Meter the switch contacts in each position; only the selected direction should close.
- 3Inspect the switch wiring and connector in the platform control box for water.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie 45-21Platform level switch fault
The platform level switch is faulted, so platform level is frozen at neutral. The fault clears after the switch is repaired and power is cycled.· OtherOtherCheck soonCauses
- Level switch jammed or worn out
- Open wire or loose pin at the level switch plug
- Corrosion in the platform control box
Checks
- 1Operate the platform level switch both ways and check it springs back by itself.
- 2Meter the level switch contacts; only the selected direction should close.
- 3Look at the level switch connector inside the platform box for green corrosion.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie 46-21Primary extend/retract switch fault
The primary extend/retract switch is faulted. Platform extend/retract is frozen at neutral until power is cycled with the problem corrected.· OtherOtherCheck soonCauses
- Extend/retract switch stuck or wiring shorted
- Switch connector corroded
Checks
- 1Check the switch and its wiring in the platform box.
- 2Power up the controller after repair.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie 75-34Primary and secondary controller software mismatch
The software in the primary and secondary controllers does not match. The Overload LED is on, functions are cut and the engine shuts down; auxiliary functions work except extend.· Part or controllerPart or controllerStop nowCauses
- Wrong software in the secondary microcontroller
- Controller replaced with a different software version
- Interrupted software update
- Mixed software packages loaded
Checks
- 1Read the software part numbers of the primary and secondary controllers on the service screen.
- 2Install the correct software part number and version in the secondary controller.
- 3Confirm the software matches the machine model.
- 4Replace the controller if it will not take the correct software.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Genie 76-12Platform load cell overloaded
The platform load cell reads overload. The Overload LED is on, functions are cut and the engine shuts down; auxiliary functions work except extend.· Real conditionReal conditionStop nowCauses
- Platform overloaded
- Load cell cable damaged
- CAN circuit open or shorted
- Load cell fault or loss of power
Checks
- 1Remove the load and cycle power; check the code clears with the platform empty.
- 2Check the load cell cable for damage along its length.
- 3Check the CAN circuit for an open or short; the manual gives 60 ohm between CAN high and low.
- 4Check for power and ground at the load cell connector with the key on.
- 5Replace the load cell if the overload reading stays with the platform empty.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 76-13Platform load cell no response
The platform load cell is not answering on the CAN bus. The Overload LED is on and functions are disabled with engine shutdown; auxiliary functions work except extend.· Lost messageLost messageStop nowCauses
- CAN bus circuit open or short
- Load cell cable damaged
- No power at the load cell
Checks
- 1Check the CAN bus circuit for an open or short.
- 2Check for cable damage to the load cell and for power at the load cell.
- 3Confirm the load cell is properly pre-loaded and free of obstructions.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Genie 76-15Platform load cell value too low
The platform load cell reads too low. The Overload LED is on and functions are disabled with engine shutdown; auxiliary functions work except extend.· Real conditionReal conditionStop nowCauses
- Load cell not properly pre-loaded
- Load cell cable damaged
- Obstruction at the load cell
Checks
- 1Confirm the platform load cell is properly pre-loaded and free of obstructions.
- 2Check for cable damage to the load cell.
- 3Calibrate the load cell.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 76-17Platform load cell not calibrated
The platform load cell is not calibrated. The Overload LED is on and the machine is restricted; with zero load calibrated but gain not, it runs with reduced capacity.· Real conditionReal conditionStop nowCauses
- Load cell replaced or not calibrated
- Controller reset or software updated
- Calibration data lost
Checks
- 1Calibrate the load cell with the correct test load per the service manual.
- 2Confirm the load cell is properly pre-loaded and free of obstructions.
- 3Check the load cell cable and connector for damage.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 76-21Platform load cell internal status fault
The platform load cell reports an internal status fault. The alarm sounds, the Overload LED is on and functions are disabled with engine shutdown.· Real conditionReal conditionStop nowCauses
- Load cell damaged inside
- Load cell cable damaged
Checks
- 1Inspect the load cell for damage.
- 2Cycle power off then on; replace the load cell if the fault persists.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 76-31Platform load cell invalid setup
The platform load cell has an invalid setup. The alarm sounds, the Overload LED is on and functions are disabled with engine shutdown.· Real conditionReal conditionStop nowCauses
- Load cell calibrated with the wrong load
- Load cell replaced and not set up
Checks
- 1Calibrate the load cell with the proper load.
- 2Replace the load cell if calibration fails.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 76-36Platform load cell cross check fault
The platform load cell fails the cross check against the second sensor. The alarm sounds, the Overload LED is on and functions are disabled with engine shutdown.· Real conditionReal conditionStop nowCauses
- Load cell damaged
- Cable or connector fault
Checks
- 1Inspect the load cell for damage.
- 2Cycle power off then on; replace the load cell if the fault persists.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 79-13Hour meter no response
Communication with the hour meter is lost. The machine functions normally, but the hour meter does not update until the link is restored.· OtherOtherInfoCauses
- Hour meter power or ground fault
- CAN bus fault between the controller and hour meter
- Loose or corroded hour meter connector
- Failed hour meter
Checks
- 1Check power and ground at the hour meter connector with the key on.
- 2Check the CAN bus circuit for an open or short.
- 3With power off, measure resistance between CAN high and CAN low; the manual gives 60 ohm.
- 4Inspect the hour meter connector for water and corrosion.
- 5Replace the hour meter if power, ground and CAN are good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Genie 82-21Overload recovery fault
The platform was overloaded and the machine is being operated on auxiliary power. The fault stays until a reset is done.· Real conditionReal conditionCheck soonCauses
- Platform overloaded while on auxiliary power
- Reset not done
Checks
- 1Enter the reset code using calibration mode.
- 2Remove excess weight from the platform.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 102-12Overload cutout relay: 12 V present when off
The controller sees 12 V from the overload cutout relays when they should be off. The Overload LED is on, functions are cut and the engine shuts down.· Real conditionReal conditionStop nowCauses
- Overload cutout relay CR54 or CR55 stuck closed
- Harness short to 12 V at SCON C41-6
- Relay contacts welded
Checks
- 1Check for 0 V at SCON C41-6 with the relays off; the manual expects 0 V.
- 2Replace CR54 or CR55 if terminal 87 shows 12 V with terminals 85 and 86 not energised.
- 3Check the harness for a short to 12 V on the relay output wire.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 102-15Overload function cutout relay: 0 V when on
The SCON sees 0 VDC from CR54 or CR55 terminal 87 when terminals 85 and 86 are energised. The alarm sounds, the Overload LED is on and functions are disabled with engine shutdown.· Real conditionReal conditionStop nowCauses
- CR54 or CR55 relay failed
- Open in the harness to SCON C41-6
Checks
- 1Check for 0 VDC at SCON C41-6; it should read 12 VDC.
- 2Replace CR54 or CR55 and check the harness for an open.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Genie 103-12Overload engine cutout relay: input seen when off
The controller sees an input from TB21 while engine cutout relay CR56 is not energised. The Overload LED is on, functions are cut and the engine shuts down.· Real conditionReal conditionStop nowCauses
- Overload engine cutout relay CR56 stuck closed
- Short from TB21 in the harness to SCON C42-2
- Relay contacts welded
Checks
- 1Replace CR56 if terminal 87 shows voltage with the relay not energised.
- 2Check the harness between TB21 and SCON C42-2 for a short to supply.
- 3Check there is no voltage at SCON C42-2 with the relay off.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Check the wiring and connector of the named sensor, switch or relay for damage and corrosion.
- 2Read the live value in the service menu with the boom in a known position and compare it with the cross-check sensor.
- 3Calibrate the sensor or load cell after repair, following the manual.
- 4Check the relay and its supply voltage against the commanded state, then cycle the key switch to clear the code.
Causes
- Sensor or switch wiring open or shorted
- Sensor out of calibration after replacement
- Relay contacts or relay supply not matching the commanded state
- Primary and secondary controller software or readings that disagree
Most codes here: real condition (13 of 25)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: Boom speed is reduced, the boom must retract into the safe envelope, or the Overload LED comes on with functions disabled and the engine shut down.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
