EF Logo

Genie · Platform load sense faults (S-60 HC)

Genie Load sense load cell, relays and system checks fault codes

The S-60 HC load sense controllers watch the platform load cell (error source 41 operational, 42 safety), drive the power relays and directional relays (error source 12 types 23 to 26) and report system checks as error source 12: safety envelope, load limit, CAN link, sensor power and sensor activity.

FaultStopLS 12-11Genie · Load sense load cell, relays and system checks
Code shows hereFAULTLS 12-11

Where this code shows

Scissors: read the code on the platform LED display or the ground control LCD.

What do these codes mean?

Genie codes LS 12-11 to LS 42-21 are all about the load sense load cell, relays and system checks. The most common failure type is real condition (6 of 25); 21 need an immediate stop. Start with this check: check the load cell wiring and connector and write down the reading before moving on.

How urgent are they?

21 of 25 codes here mean stop now; 4 are information only.

  • Stop now21
  • Info4

What should I check first?

Check the load cell wiring and connector and write down the reading before moving on.

Shared checks

25 of 25

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Genie LS 12-11Safety envelope reached

    The boom has reached the edge of its safe envelope.· Other
    Stop now

    Causes

    • Boom moved beyond the safe envelope
    • Load and reach combination too severe

    Checks

    1. 1Use the recovery switch and APU from the ground controls to bring the boom within the envelope.
    2. 2Retract or lower the boom to stowed.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie LS 12-12Platform load greater than limit

    The platform load is above the allowed limit.· Other
    Stop now

    Causes

    • Platform overloaded
    • Load cell reading too high

    Checks

    1. 1Remove weight from the platform until the load is below 1250 lb (567 kg).
    2. 2Recalibrate the load cell if the reading stays high with an empty platform.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie LS 12-13CAN communication failure

    The load sense controllers have lost CAN communication.· Lost message
    Stop now

    Causes

    • CAN bus wiring open or shorted
    • Controller connector loose

    Checks

    1. 1Repair the CAN bus wiring and connections.
    2. 2Check termination resistance on the CAN bus.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Genie LS 12-14Sensor power failure

    The load sense controllers report a failure of the supply to the sensors.· Other
    Stop now

    Causes

    • Sensor supply wire open or shorted
    • Controller power output failed

    Checks

    1. 1Check sensor power and ground at the sensors.
    2. 2Repair the system wiring and connections.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie LS 12-21Angle sensor not active

    The boom angle sensor is not producing a usable signal.· Other
    Stop now

    Causes

    • Angle sensor not connected to the boom
    • Angle sensor failed

    Checks

    1. 1Inspect the boom angle sensor for proper operation and connection to the boom.
    2. 2Replace the sensor if needed.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie LS 12-22String potentiometer not active

    The string potentiometer is not producing a usable signal.· Other
    Stop now

    Causes

    • String potentiometer not connected to the boom
    • String potentiometer failed

    Checks

    1. 1Inspect the string potentiometer for proper operation and connection to the boom.
    2. 2Replace the string potentiometer if needed.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie LS 12-23Power relay output short high

    A power relay output is shorted high.· Shorted high
    Stop now

    Causes

    • Relay wiring shorted to voltage
    • Relay damaged

    Checks

    1. 1Repair the system wiring and connections; relay wiring open or shorted to voltage.
    2. 2Check the relay and its socket.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie LS 12-24Power relay output short low

    A power relay output is shorted low.· Shorted low
    Stop now

    Causes

    • Relay wiring shorted to ground
    • Relay damaged

    Checks

    1. 1Repair the system wiring and connections; relay wiring open or shorted to ground.
    2. 2Check the relay and its socket.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Genie LS 12-25Directional relay output short high

    A directional relay output is shorted high.· Shorted high
    Stop now

    Causes

    • Relay wiring open or shorted to voltage
    • Relay damaged

    Checks

    1. 1Repair the system wiring and connections.
    2. 2Check the relay and its socket.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie LS 12-26Directional relay output short low

    A directional relay output is shorted low.· Shorted low
    Stop now

    Causes

    • Relay wiring open or shorted to ground
    • Relay damaged

    Checks

    1. 1Repair the system wiring and connections.
    2. 2Check the relay and its socket.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Genie LS 41-5Load cell (operational): sensor tolerance fault

    Load cell (operational): The reading is outside the sensor tolerance band without being a clean short or open.· Real condition
    Stop now

    Causes

    • Load cell (operational): sensor drifted, damaged or mechanically misaligned, so it still reports but outside tolerance
    • Wiring or connector fault on this channel

    Checks

    1. 1Compare the live reading with the real position of the boom (angle, length or platform load); a steady offset points at the sensor or its mounting, a reading that jumps when the harness is moved points at the connector.
    2. 2Remove excess weight from the platform and check for binding of the overload linkage before suspecting the load cell, and make sure the platform is not reverse loaded.
    3. 3Cycle the key switch after the repair and confirm the code does not return; the safety channel of the same sensor is cross-checked against this one, so a repair here can also clear its twin code.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie LS 41-11Load cell (operational): output short high

    Load cell (operational): The sensor output is stuck at the top of its range, as if shorted high.· Shorted high
    Stop now

    Causes

    • Load cell (operational): signal wire shorted to the sensor supply
    • Wiring or connector fault on this channel

    Checks

    1. 1Unplug the sensor and read its signal pin with the key on; supply voltage there means the harness is shorted high, while a normal reading means the sensor itself is pinned.
    2. 2Remove excess weight from the platform and check for binding of the overload linkage before suspecting the load cell, and make sure the platform is not reverse loaded.
    3. 3Cycle the key switch after the repair and confirm the code does not return; the safety channel of the same sensor is cross-checked against this one, so a repair here can also clear its twin code.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Genie LS 41-12Load cell (operational): value too high

    Load cell (operational): The sensor value is above the allowed window but not necessarily at the very top.· Real condition
    Stop now

    Causes

    • Load cell (operational): open sensor ground or a partly shorted signal wire letting the value float up
    • Wiring or connector fault on this channel

    Checks

    1. 1Read the value across the working range; a value that is high everywhere but still moves points at an open ground or a worn sensor rather than a hard short.
    2. 2Remove excess weight from the platform and check for binding of the overload linkage before suspecting the load cell, and make sure the platform is not reverse loaded.
    3. 3Cycle the key switch after the repair and confirm the code does not return; the safety channel of the same sensor is cross-checked against this one, so a repair here can also clear its twin code.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie LS 41-15Load cell (operational): value too low

    Load cell (operational): The sensor value is below the allowed window but not necessarily at zero.· Real condition
    Stop now

    Causes

    • Load cell (operational): weak or high-resistance sensor supply, or a partly grounded signal wire
    • Wiring or connector fault on this channel

    Checks

    1. 1Check the sensor supply voltage at the plug first, since a low supply drags the whole reading down.
    2. 2Remove excess weight from the platform and check for binding of the overload linkage before suspecting the load cell, and make sure the platform is not reverse loaded.
    3. 3Cycle the key switch after the repair and confirm the code does not return; the safety channel of the same sensor is cross-checked against this one, so a repair here can also clear its twin code.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie LS 41-16Load cell (operational): output short low

    Load cell (operational): The sensor output is stuck at the bottom of its range, as if shorted low.· Shorted low
    Stop now

    Causes

    • Load cell (operational): signal wire shorted to ground or the sensor supply lost
    • Wiring or connector fault on this channel

    Checks

    1. 1Check the signal wire for continuity to ground with the sensor unplugged; an open and a short to ground both read low but need different repairs.
    2. 2Remove excess weight from the platform and check for binding of the overload linkage before suspecting the load cell, and make sure the platform is not reverse loaded.
    3. 3Cycle the key switch after the repair and confirm the code does not return; the safety channel of the same sensor is cross-checked against this one, so a repair here can also clear its twin code.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Genie LS 41-17Load cell (operational): not calibrated

    Load cell (operational): The sensor has no calibration stored, so the boom range of motion is limited.· Part or controller
    Info

    Causes

    • Load cell (operational): sensor replaced or calibration lost after a reset
    • Controller reprogrammed or the sensor plug reseated during the repair

    Checks

    1. 1Run the platform load sense calibration for this sensor through its full range, then confirm the code is gone.
    2. 2Remove excess weight from the platform and check for binding of the overload linkage before suspecting the load cell, and make sure the platform is not reverse loaded.
    3. 3Cycle the key switch after the repair and confirm the code does not return; the safety channel of the same sensor is cross-checked against this one, so a repair here can also clear its twin code.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Genie LS 41-18Load cell (operational): just calibrated

    Load cell (operational): The sensor was just calibrated; this status is used to clear diagnostic codes and clears itself.· Real condition
    Info

    Causes

    • Load cell (operational): calibration just completed
    • Status reported once after the calibration routine and cleared on the next power cycle

    Checks

    1. 1This status needs no repair: cycle the power and confirm it does not return.
    2. 2Remove excess weight from the platform and check for binding of the overload linkage before suspecting the load cell, and make sure the platform is not reverse loaded.
    3. 3Cycle the key switch after the repair and confirm the code does not return; the safety channel of the same sensor is cross-checked against this one, so a repair here can also clear its twin code.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie LS 42-5Load cell (safety): sensor tolerance fault

    Same fault as LS 41-5, on the safety load cell channel; read both channels.· Other
    Stop now

    Causes

    • Safety channel wiring or connector fault
    • Safety sensor element drifted or damaged

    Checks

    1. 1Read both channels together.
    2. 2Repair the safety wiring, then cycle power.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie LS 42-11Load cell (safety): output short high

    Same fault as LS 41-11, on the safety load cell channel; read both channels.· Other
    Stop now

    Causes

    • Safety channel wiring or connector fault
    • Safety sensor element drifted or damaged

    Checks

    1. 1Read both channels together.
    2. 2Repair the safety wiring, then cycle power.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie LS 42-12Load cell (safety): value too high

    Same fault as LS 41-12, on the safety load cell channel; read both channels.· Real condition
    Stop now

    Causes

    • Safety channel wiring or connector fault
    • Safety sensor element drifted or damaged

    Checks

    1. 1Read both channels together.
    2. 2Repair the safety wiring, then cycle power.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie LS 42-15Load cell (safety): value too low

    Same fault as LS 41-15, on the safety load cell channel; read both channels.· Real condition
    Stop now

    Causes

    • Safety channel wiring or connector fault
    • Safety sensor element drifted or damaged

    Checks

    1. 1Read both channels together.
    2. 2Repair the safety wiring, then cycle power.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Genie LS 42-16Load cell (safety): output short low

    Same fault as LS 41-16, on the safety load cell channel; read both channels.· Other
    Stop now

    Causes

    • Safety channel wiring or connector fault
    • Safety sensor element drifted or damaged

    Checks

    1. 1Read both channels together.
    2. 2Repair the safety wiring, then cycle power.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie LS 42-17Load cell (safety): not calibrated

    Same fault as LS 41-17, on the safety load cell channel; read both channels.· Other
    Info

    Causes

    • Safety channel wiring or connector fault
    • Safety sensor element drifted or damaged

    Checks

    1. 1Read both channels together.
    2. 2Repair the safety wiring, then cycle power.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie LS 42-18Load cell (safety): just calibrated

    Same fault as LS 41-18, on the safety load cell channel; read both channels.· Other
    Info

    Causes

    • Safety channel wiring or connector fault
    • Safety sensor element drifted or damaged

    Checks

    1. 1Read both channels together.
    2. 2Repair the safety wiring, then cycle power.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Genie LS 42-21Load cell (safety): inconsistent

    Same fault as LS 41-21, on the safety load cell channel; read both channels.· Other
    Stop now

    Causes

    • Safety channel wiring or connector fault
    • Safety sensor element drifted or damaged

    Checks

    1. 1Read both channels together.
    2. 2Repair the safety wiring, then cycle power.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Check the load cell wiring and connector and write down the reading before moving on.
  2. 2Remove excess weight from the platform and check for binding of the overload linkage.
  3. 3Check the relay and its socket against the wiring diagram, and measure the relay output voltage on and off.
  4. 4Replace the load cell if the fault persists, then calibrate the overload system.

Causes

  • Load cell wiring open or shorted
  • Platform overloaded or reverse loaded
  • Load cell not calibrated or failed
  • Relay wiring shorted high or low, or relay damaged

Most common here: real condition (6 of 25)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: Power relays disengage, the boom stops or its range of motion is limited.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.