EF Logo

J1939 · Fuel system

SPN 1347 Fault Code

Fuel pump pressurizing assembly

What does SPN 1347 mean?

The high-pressure fuel pump assembly that builds common-rail pressure, with its metering driver switched by the ECM. How urgent it is depends on the FMI after SPN 1347 - pick it below. Check first: measure the metering solenoid resistance at the pump connector and compare it with the manual range.

FaultActiveSPN 1347FMI --J1939 engine ECU
SPN 1347
Fuel pump pressurizing assembly
FMI ?
How it failed - the number after the SPN

Can I keep running with it?

Depends on the FMI

How urgent it is depends on the FMI after SPN 1347 - pick it below.

What should I check first?

Measure the metering solenoid resistance at the pump connector and compare it with the manual range

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a J1939-capable scan tool to the 9-pin diagnostic port.

Which FMI shows after SPN 1347?

You'll notice: Rail pressure may not build, so the engine can crank without starting, lose power or stall, and the ECM may shut it down on low pressure.

Find the number shown after SPN 1347 on your display.

  • 3SPN 1347 FMI 3: Fuel pump pressurizing assembly signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, PACCAR MX-13
  • 4SPN 1347 FMI 4: Fuel pump pressurizing assembly signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, PACCAR MX-13
  • 5SPN 1347 FMI 5: Current in the Fuel pump pressurizing assembly circuit is below normal, or the circuit is openOpen circuitPACCAR MX-13
  • 6SPN 1347 FMI 6: Current in the Fuel pump pressurizing assembly circuit is above normal, or the circuit is groundedShorted lowPACCAR MX-13
  • 7SPN 1347 FMI 7: The Fuel pump pressurizing assembly is not responding or is out of adjustmentPart or controllerCummins ISX15
  • 16SPN 1347 FMI 16: Fuel pump pressurizing assembly is above the normal range, moderately severe levelReal conditionPACCAR MX-13
  • 18SPN 1347 FMI 18: Fuel pump pressurizing assembly is below the normal range, moderately severe levelReal conditionPACCAR MX-13
  • 20SPN 1347 FMI 20: Fuel pump pressurizing assembly has drifted highErratic or implausiblePACCAR MX-13
  • 21SPN 1347 FMI 21: Fuel pump pressurizing assembly has drifted lowErratic or implausiblePACCAR MX-13

Checks

0 of 5 done

When to stop

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

How urgent SPN 1347 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Causes

  • Pump metering solenoid open or shorted
  • Pump pigtail damaged at the pump
  • Low-pressure supply restricted, so the pump cannot hold rail pressure
  • Worn high-pressure pump

Source

Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)

This list names SPN 1347 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.

The source covers: Cummins ISX15, PACCAR MX-13; same SPN on other J1939 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.