J1939 · Aftertreatment - SCR/DEF
SPN 3226 Fault Code
Aftertreatment 1 outlet NOx
What does SPN 3226 mean?
Nitrogen oxide level in the exhaust leaving the SCR, measured by the downstream NOx sensor. The ECM uses it to check SCR performance and DEF dosing. How urgent it is depends on the FMI after SPN 3226 - pick it below. Check first: check the downstream sensor connector and lead along the tailpipe for corrosion and chafing.
- SPN 3226
- Aftertreatment 1 outlet NOx
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 3226 - pick it below.
What should I check first?
Check the downstream sensor connector and lead along the tailpipe for corrosion and chafing
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 3226?
You'll notice: The NOx sensor after the SCR is faulty or unreliable, so the ECM cannot confirm that the SCR is cutting NOx.
Find the number shown after SPN 3226 on your display. 6 of them have their own page with causes and checks.
- 2SPN 3226 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 3SPN 3226 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highDetroit DD15, Mack MP8, Mack MP7, Volvo D13
- 4SPN 3226 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15
- 5SPN 3226 FMI 5: Current is below normal, or the circuit is openOpen circuitMack MP8, Mack MP7, Volvo D13
- 8SPN 3226 FMI 8: Outlet NOx sensor operation is not stable, or its reading is stuckErratic or implausibleDetroit DD13 Gen 5, Detroit DD15 Gen 5, PACCAR MX-13
- 9SPN 3226 FMI 9: Abnormal update rate: the signal or message is late or missingLost messageCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 10SPN 3226 FMI 10: The value is changing at an abnormal rateErratic or implausibleCummins ISX15
- 11SPN 3226 FMI 11: A fault exists but the ECM cannot identify its causeOtherCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 12SPN 3226 FMI 12: Bad intelligent device or componentPart or controllerMack MP8, Mack MP7, Volvo D13
- 13SPN 3226 FMI 13: The value is out of calibrationPart or controllerCummins ISX15, Mack MP8, Mack MP7, PACCAR MX-13 and 1 more
- 14SPN 3226 FMI 14: A special-instruction condition defined by the engine maker appliesOtherMack MP8, Mack MP7, Volvo D13
- 16SPN 3226 FMI 16: Outlet NOx sensor data is not rational and has drifted highReal conditionPACCAR MX-13
- 20SPN 3226 FMI 20: Outlet NOx sensor has drifted, or its oxygen pump is out of range highErratic or implausibleCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 1 more
- 21SPN 3226 FMI 21: Outlet NOx sensor has drifted, or its oxygen pump is out of range lowErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 31SPN 3226 FMI 31: A condition exists: the ECM is flagging a defined state rather than a circuit failureReal conditionMack MP8, Mack MP7, Volvo D13
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 3226 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Circuit fault at the downstream sensor plug near the tailpipe: road spray, corrosion or a chafed lead
- Downstream NOx sensor failed, aged or coated with DEF residue or soot
- Tailpipe or silencer joint leak near the sensor, pulling air into the sample
- Sensor module supply, ground or CAN fault
Other Aftertreatment - SCR/DEF codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 3226 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
