EF Logo

J1939 · Aftertreatment - SCR/DEF

SPN 5848 Fault Code

SCR intermediate ammonia sensor

What does SPN 5848 mean?

Ammonia (NH3) sensor placed between SCR catalyst stages. It lets the control module see ammonia slip and trim the dose. How urgent it is depends on the FMI after SPN 5848 - pick it below. Check first: read the NH3 sensor value at warm idle and see whether it is pinned or follows load.

FaultActiveSPN 5848FMI --J1939 engine ECU
SPN 5848
SCR intermediate ammonia sensor
FMI ?
How it failed - the number after the SPN

Can I keep running with it?

Depends on the FMI

How urgent it is depends on the FMI after SPN 5848 - pick it below.

What should I check first?

Read the NH3 sensor value at warm idle and see whether it is pinned or follows load

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a J1939-capable scan tool to the 9-pin diagnostic port.

Which FMI shows after SPN 5848?

You'll notice: The controller cannot fine-tune dosing, so SCR efficiency or ammonia slip codes can follow.

Find the number shown after SPN 5848 on your display.

  • 2SPN 5848 FMI 2: SCR intermediate ammonia sensor data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, PACCAR MX-13
  • 3SPN 5848 FMI 3: SCR intermediate ammonia sensor signal voltage is above normal, or the circuit is shorted to a high sourceShorted highPACCAR MX-13
  • 4SPN 5848 FMI 4: SCR intermediate ammonia sensor signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, PACCAR MX-13
  • 5SPN 5848 FMI 5: Current in the SCR intermediate ammonia sensor circuit is below normal, or the circuit is openOpen circuitPACCAR MX-13
  • 7SPN 5848 FMI 7: The SCR intermediate ammonia sensor is not responding or is out of adjustmentPart or controllerCummins ISX15
  • 9SPN 5848 FMI 9: Abnormal update rate: the SCR intermediate ammonia sensor data is late or not arrivingLost messageCummins ISX15, PACCAR MX-13
  • 10SPN 5848 FMI 10: SCR intermediate ammonia sensor is changing at an abnormal rateErratic or implausibleCummins ISX15, PACCAR MX-13
  • 11SPN 5848 FMI 11: Fault for SCR intermediate ammonia sensor with a root cause that is not knownOtherPACCAR MX-13
  • 12SPN 5848 FMI 12: Failure inside the device or component that handles the SCR intermediate ammonia sensorPart or controllerCummins ISX15
  • 13SPN 5848 FMI 13: The SCR intermediate ammonia sensor value is out of calibrationPart or controllerCummins ISX15, PACCAR MX-13
  • 16SPN 5848 FMI 16: SCR intermediate ammonia sensor is above the normal range, moderately severe levelReal conditionPACCAR MX-13
  • 19SPN 5848 FMI 19: Network data received for the SCR intermediate ammonia sensor is in errorLost messagePACCAR MX-13
  • 20SPN 5848 FMI 20: SCR intermediate ammonia sensor has drifted highErratic or implausiblePACCAR MX-13
  • 21SPN 5848 FMI 21: SCR intermediate ammonia sensor has drifted lowErratic or implausiblePACCAR MX-13

Checks

0 of 5 done

When to stop

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

How urgent SPN 5848 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Causes

  • Sensor probe fouled or aged
  • Sensor control unit failed
  • Exhaust heat damage to the sensor lead
  • Connector corrosion

Source

Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)

This list names SPN 5848 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.

The source covers: Cummins ISX15, PACCAR MX-13; same SPN on other J1939 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.