J1939 · Aftertreatment - SCR/DEF
SPN 1761 Fault Code
Aftertreatment 1 DEF tank level
What does SPN 1761 mean?
Level of diesel exhaust fluid (DEF) in the tank, read by a level sensor in the tank or the dosing unit. How urgent it is depends on the FMI after SPN 1761 - pick it below. Check first: look into the tank and compare the real level with the gauge; a full tank reading empty confirms a sender or circuit fault.
- SPN 1761
- Aftertreatment 1 DEF tank level
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 1761 - pick it below.
What should I check first?
Look into the tank and compare the real level with the gauge; a full tank reading empty confirms a sender or circuit fault
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 1761?
You'll notice: The DEF gauge reads wrong or shows empty on a tank that has fluid, so the ECM may start a low-DEF warning or an inducement derate for no reason.
Find the number shown after SPN 1761 on your display. 3 of them have their own page with causes and checks.
- 1SPN 1761 FMI 1: Value is below the normal range, most severe levelReal conditionCummins ISX15, PACCAR MX-13
- 2SPN 1761 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 3SPN 1761 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 5 more
- 4SPN 1761 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 2 more
- 5SPN 1761 FMI 5: Current is below normal, or the circuit is openOpen circuitMack MP8, Mack MP7, Volvo D13
- 9SPN 1761 FMI 9: Abnormal update rate: the signal or message is late or missingLost messageCummins ISX15
- 10SPN 1761 FMI 10: The value is changing at an abnormal rateErratic or implausibleCummins ISX15
- 11SPN 1761 FMI 11: A fault exists but the ECM cannot identify its causeOtherCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 13SPN 1761 FMI 13: The value is out of calibrationPart or controllerCummins ISX15
- 14SPN 1761 FMI 14: A special-instruction condition defined by the engine maker appliesOtherMack MP8, Mack MP7, Volvo D13
- 17SPN 1761 FMI 17: Value is below the normal range, least severe levelReal conditionCummins ISX15
- 18SPN 1761 FMI 18: Value is below the normal range, moderately severe levelReal conditionCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 19SPN 1761 FMI 19: The DEF tank level message arrived in error over CANLost messagePACCAR MX-13
- 31SPN 1761 FMI 31: DEF tank level is very low (level 3 condition)Real conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
Checks
0 of 5 done
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
How urgent SPN 1761 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Signal high or open: open signal or return wire, or the signal touching a supply wire, at the DEF tank level sensor
- Signal low or shorted: signal wire grounded, or the supply to the DEF tank level sensor lost
- Real condition: tank low or empty so the low-level reading is real
- Real condition: sender unit float stuck or contaminated
1 more causeFewer causes
- Sensor: sloshing fluid in a part-empty tank making the float reading jump
Other Aftertreatment - SCR/DEF codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 1761 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
