J1939 · Aftertreatment - DPF
SPN 3610 Fault Code
Aftertreatment 1 diesel particulate filter outlet pressure
What does SPN 3610 mean?
Exhaust pressure at the DPF outlet, read by a pressure sensor. The ECM uses it, with the inlet reading, to calculate pressure drop and soot load. How urgent it is depends on the FMI after SPN 3610 - pick it below. Check first: with the engine off, read the outlet pressure: it should be near ambient, and a full-scale value points to the circuit.
- SPN 3610
- Aftertreatment 1 diesel particulate filter outlet pressure
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 3610 - pick it below.
What should I check first?
With the engine off, read the outlet pressure: it should be near ambient, and a full-scale value points to the circuit
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 3610?
You'll notice: The DPF outlet pressure is misread, so the ECM cannot judge the filter state or exhaust backpressure, and it can derate or block regeneration with a lamp on.
Find the number shown after SPN 3610 on your display. 2 of them have their own page with causes and checks.
- 2SPN 3610 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 2 more
- 3SPN 3610 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Detroit DD15, Detroit DD13, PACCAR MX-13
- 4SPN 3610 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13, PACCAR MX-13
- 10SPN 3610 FMI 10: The value is changing at an abnormal rateErratic or implausibleCummins ISX15
- 12SPN 3610 FMI 12: DPF outlet pressure reading is not plausiblePart or controllerDetroit DD13 Gen 5, Detroit DD15 Gen 5
- 16SPN 3610 FMI 16: DPF outlet pressure data is erratic or incorrect at key-on or in operationReal conditionPACCAR MX-13
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 3610 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Signal high or open: broken or backed-out pin, an open sensor return, or the signal shorted to the 5 V reference at the DPF outlet pressure sensor
- Signal low or shorted: signal wire grounded, or the 5 V reference lost, so the DPF outlet pressure sensor reads at the bottom of its range
- Real condition: exhaust restriction after the DPF, or a real leak at the tap
- Real condition: damaged DPF can or clamp causing a false pressure reading
1 more causeFewer causes
- Sensor: condensate in the outlet hose making the reading bounce
Other Aftertreatment - DPF codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 3610 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
